Installation Guide

ManualsBrandsHolcam ManualsAlcove Shower DoorsLuna 58-1/16 in. - 60 in. W x 74 in. H Frameless Bypassing Sliding Shower Door in Oil Rubbed Bronze

This installation sheet is a required component in Parts Bag BP.5011

FIRST STEPS - Identify the model number of your unit.

- Look on the white shipping label on the outer cardboard box.

- Model number on label should correspond to one listed above.

3/8” Door Models: NBSE/NBTE or LBSE/LBTE

Installation Instructions for

Required Tools

* Pencil or water soluble felt pen

* Hacksaw with 24 tooth blade

* Metal file (smooth sharp edges)

* Tape measure

* Clear 100% Silicone (recommended)

* #2 Phillips Screw driver

* 1/4” drill bit carbide for tile

* Caulking gun

* Drill, electric or battery

* 4 ft. Level

* Rubber mallet

* Razor knife

NOTE:

Ÿ Installation procedures are the same for tub or shower height units

Ÿ The images in this manual show an arrangement with the showerhead to the left. The same

instructions apply for the opposite orientation where the examples would be reversed.

NBSE/LBSE NBTE/LBTE

MM.5073

rev041019

Summary of content (8 pages)

PAGE 1
Installation Instructions for 3/8” Door Models: NBSE/NBTE or LBSE/LBTE FIRST STEPS - Identify the model number of your unit. - Look on the white shipping label on the outer cardboard box. - Model number on label should correspond to one listed above. NBSE/LBSE NBTE/LBTE NOTE: Ÿ Installation procedures are the same for tub or shower height units Ÿ The images in this manual show an arrangement with the showerhead to the left.
PAGE 2
Thank you for purchasing this outstanding product! This booklet will help you install your units safely and successfully. READ - Warnings and General Shower Door Information on this page before beginning installation SAFETY WARNINGS: HEAVY CAUTION SHARP GLASS FRAGILE Follow instructions: Instructions must be read and followed carefully to reduce the risk of serious injury during and after installation. Any deviation from these instructions can create safety hazards.
PAGE 3
Parts Diagram for NBSE, NBTE, LBSE or LBTE (Install procedure is the same regardless of height of unit) 3b Page 3 3g 3c 3h 3f 8 1 6 3a 7 9 12 3h 6 12 7 3b 9 3f 7 3h - Hex Keys 4 3a 3c 3g 8 5 10 11 15 12 3mm 3mm 15 5mm 3d 14 2 14 3e 13 13 Parts List ITEM PART # 1 HA.3230 DESCRIPTION QTY 60” Header Bar (72”-HA.3231) 1 ITEM PART # 4 GLASS DESCRIPTION Outside Panel QTY 1 2 HA.3212 Center Guide 1 5 GLASS Inside Panel 1 3 BP.5011 Part Bag 1 6 HA.
PAGE 4
Installation Instructions All Models a. With a level, determine the vertical threshold outage as shown in Illustration 1. Maximum recommended vertical threshold outage from side to side is ¼”. Illustration #1 STEP 1 - EVALUATE THRESHOLD Page 4 b. Mark high side and low side of threshold. The first header block will be installed on the high side. a. Mark the location of the center of the threshold. b. Draw overall unit centerline on threshold and walls.
PAGE 5
Installation Instructions All Models a. Your Header Bar may already be cut to size. To check, measure wall to wall just below the Header Block and subtract ¾”. If your header is not this length, find the difference between the overall length of the Header Bar and your measurement. Remove half of this difference from each end of the Header Bar (Illustration 4).
PAGE 6
Installation Instructions All Models a. Starting with the Inside Panel, mount two Roller assemblies as shown in Illustration 7. The side of the panel with the wheels will be oriented to the outside of the shower. Illustration #7 STEP 8 - INSTALL SLIDING PANELS Showerhead Wall d. Mount both wheels onto the Outside Panel using the same procedure as above. The side of the panel with the wheels will be oriented to the inside of the shower.
PAGE 7
Installation Instructions All Models Illustration #10 Page 7 STEP 11 - INSTALL AND ADJUST ANTI JUMPS a. Assemble two Anti Jumps onto each glass panel so that they are snug but not tight. b. Rotate outer cam/cap with the provided 3mm hex keys as demonstrated in Illustration 10 to raise or lower Anti Jumps until they are approximately 1/16” from the bottom of the Header Bar. ANTI JUMP Glass Panel Adjust Anti Jump to create a 1/16”gap to the Header Bar 1/16” c.
PAGE 8
Installation Instructions All Models a. Measure the distance between the wall and the nearest side of the Center Guide, see Illustration 13. b. Cut Soft Sill to this dimension. Illustration #13 STEP 13 - INSTALL SOFT SILL Page 8 Threshold wall c. Repeat for the other side of the Center Guide. Soft Sill NOTE: Clean adhesion surface with alcohol and dry thoroughly. e. Repeat for second piece of Soft Sill. STEP 14 - SILICONE a.