Installation Manual Showerhead this wall Showerhead this wall MODEL: L2BSE Shower MODEL: L2BTE Tub Installation Video (scan me) NOTE: Ÿ Installation procedures are the same for tub or shower height units Ÿ The images in this manual show an arrangement with the showerhead to the right. The same instructions apply for the opposite orientation where the examples would be reversed.
READ ENTIRE MANUAL BEFORE INSTALLATION AND OPERATION Warnings and General Shower Door Information CAUTION SAFETY WARNINGS: HEAVY CAUTION EYE PROTECTION REQUIRED SHARP GLASS FRAGILE EYEWARE READ AND FOLLOW INSTRUCTIONS: Failure to follow all instructions, warnings and guidelines may result in serious injury or death, may cause water damage, and will void the terms of your warranty.
Sizing Guide H W W Opening LBSE 60 x 76 LBSE 48 x 76 LBTE 60 x 76 LB_E XX x YY Fits Widths (W) 56"-60" 44"-48" 56"-60" (XX-4)" - XX" 24"-28" 18"-22" 24"-28" Height (H) 76" 76" 60" (XX/2)-2" YY" Clear Opening
Exploded View 9 10 1 13 2 3 14 4L 4R 5 8 7 12 6 15 NOTE Four vinyl inserts come pre-inserted into the wall profiles 10mm 11 19mm 16 VN.4309.CLR.076 HA.3313.
Parts List 1 2 3 Outside Glass Door Header Bracket HA.3311 x2 4L The Left Wall Profile HA.3305 Outside Roller HA.3301 x2 6 The Right Wall Profile HA.3305 x1 5 4R x1 GL.CLR.L2BSE-24 7/8x75-3/8-V1 GL.CLR.L2BSE-30 7/8x75-3/8-V1 GL.CLR.L2BSE-30 7/8x59-3/8-V1 x1 x2 Handles HA.2709 8 7 Inside Glass Door Splash Guard HA.3207 x1 9 Header HA.3303 x1 Inside Roller HA.3302 x1 Screw M5x60 BP.5015 x2 3mm Hex Key HA.2709 10mm and 19mm Wrench BP.
Model Specific Instruction 1/2” Out-of-Plumb adjustment per side. Threshold must be level within 1/4”. Verify walls and threshold with a level to ensure proper fitment. 3” minimum threshold* *If threshold is below 3” see Alternate D Detail on page 6. NOTE This model is reversible for right-hand or left-hand door installation. The right-hand door installation is shown as an example throughout this manual.
Guideline Placement Detail D Typical Bottom Guide Inside of shower Outside of shower Silicone bead VHB tape 3/8” A Threshold D 3” Flat width of threshold B Alternate Detail D Threshold Guideline (A to B) The “flat width” of the threshold does not include rounded edges. Measure 3/8” from the front of the threshold to the back, this will be the Threshold Guideline for the front of the splash guard. Draw this line from A to B and record the distance.
READ THIS FIRST BEFORE BEGINNING INSTALLATION TO HELP AVOID FUTURE WATER DAMAGE R E Sealing Screws and Anchors: Follow these steps when drilling, anchoring or screwing into a vertical, horizontal or sloped surface of a tub, shower, wall or ceiling, otherwise moisture damage can occur: 1. Drill hole and evacuate all debris 2. Insert silicone into the hole 3. 4. 5. If using an anchor: a. Insert anchor (cut anchor shoulder off if it interferes with part being attached) b.
Install Wall Jambs 3. Place the Left Wall Profile (4L) and the Right Wall Profile (4R) against the two walls, make sure that the Wall Profiles are vertical to the floor. 4 NOTE: Refer to the "Proper Backing" bullet on Page 2. Mark down the predrilled holes on the Wall Profiles. Please see Fig 3 for details Fig 3 4. Drill the holes in the wall using a 3/8” drill bit and apply silicone sealant into the holes, insert the 5/16” Wall Anchors (14). Please see Fig 4 for details a. b. c.
Install Header Brackets 5. Secure the Wall Profiles (4R)(4L) and the Header Brackets (1) to the walls with M5x60 Screws (12). a. Note: colored screws go in bottom holes Remember to apply the adhesive clear plastic Header Bracket Seal to back of Header Bracket The slots in the Wall Profiles (4R)(4L) and the Header Brackets (1) allow for adjustability. 1 When installing these components, ensure the heads of the screws are in the middle of the slots. Adjustments may be required in step 6. c. b.
Install Header a. 1 9 W b. 1 9 6. Measure from wall to wall at the height of the Header Brackets (1). Cut Header (9) to W - 1 1/2” and insert into Header Brackets (1). Please see Fig 6 for details c. e. d. 1A 1A f.
Level the Header Fig 7 7. Ensure that the Header (9) is level. If an adjustment needs to be made, return to step 5 and use the slots in the Header Block (1) and Wall Profiles (4) to fix alignment.
Install Center Guide a. 7 6 b. 7 6 d. c. e. 15 8. Place the Bottom Guide (7) to the Splash Guard (6), now mark down the hole on the Bottom Guide (7) . Drill the hole in the Splash Guard with a 5/16" drill bit and apply silicone into the hole, and then insert the 1/4” Wall Anchor (15).
Install Center Guide a. 12 7 b. Fig 9 9. Install the Bottom Guide (7) to the shower base using the M4x30 Screw (12).
Install Inside Rollers a. 10 NOTE Shower Door rotated to show inside view 10 10A 10 10B b. 5 10 c. 8 8 5 10. Install the Inside Rollers (10) and a Handle (5) to the Inside Glass Door (8).
Install Outside Rollers a. NOTE 2 Shower Door rotated to show outside view 2 2C 2 2A 2B b. 2 3 5 c. Fig 11 11. Install the Outside Rollers (2) and a Handle (5) to the Outside Glass Door (3).
Roller/Panel Detail 3 8 7 Steps 12 and 13 involve hanging the shower doors on the Header (9). The figure above can be used to gain an understanding of how the parts will come together in these steps.
Install Inside Panel NOTE Shower Enclosure rotated to show inside view on the right side of this page 8 a. 8 c. 10 b. d. 8 Fig 12 12. Hang the Glass Door Assembly to the Header (9) and then make sure that the rollers are fully seated in the track. If the notches for the rollers do not line up exactly with the rollers on your door, you can place both rollers in the track one at a time.
Install Outside Panel 9 2 13. Hang the Glass Door Assembly to the Header (9) and then make sure that the roller is rolling against the track of the Header (9). 3 Please see Fig 13 for details b. a. 3 3 7 c.
Panel/Roller Adjustment 2 a. 2B 2B b. Fig 14 2A 14. Adjust the Outside Rollers (2) to ensure that the Outside Glass Door (3) is aligned with the Left Wall Profile (4L). c.
Panel/Roller Adjustment NOTE 10 a. 10B 10B Shower Enclosure rotated to show inside view b. 15. Adjust the Inside Rollers (10) to ensure that the Inside Glass Door (8) is aligned with the Right Wall Profile (4R).
Caulk Unit with Silicone Sealant Fig 16 16. Remove any painters tape used during installation and clean surfaces with denatured alcohol. Apply a continuous bead of high quality, clear 100% silicone on the outside of the unit where it meets the wall and threshold. Specifically, run the silicone down the Wall Profiles (4L)(4R) at the wall, and along the Splash Guard (6) at the threshold.
This page intentionally left blank.
This page intentionally left blank.
