72" INDY ™ INDOOR / OUTDOOR FAN DC WET CEILING FAN INSTRUCTION MANUAL
WE WANT YOU TO LOVE YOUR NEW FAN SO WE’RE HERE IF YOU HAVE A QUESTION, NEED SOME HELP OR WANT TO CHAT ABOUT OUR PRODUCTS. SEND SUGGESTIONS OUR WAY TOO—WE’RE ALWAYS LOOKING TO MAKE YOUR EXPERIENCE WITH HINKLEY A POSITIVE ONE. > SERVICE@HINKLEY.COM > 800.HINKLEY > LET’S SEE THAT HINKLEY STYLE @HINKLEY #HINKLEYSTYLE This manual contains complete instructions for the installation and operation of this fan. It has been designed to make the installation process as easy as possible.
TABLE OF CONTENTS 02 GENERAL INSTALLATION & OPERATING INSTRUCTIONS 11 BLADE ATTACHMENT 03 IMPORTANT SAFETY PRECAUTIONS 12 INSTALLATION OF LOWER COVER 03 TOOLS & MATERIALS REQUIRED 13 OPERATION 04 UNPACKING YOUR FAN 15 CARE AND CLEANING 05 PREPARATION 15 TROUBLESHOOTING 05 INSTALLING THE HANGING BRACKET 16 ENERGY GUIDE 06 HANGING THE FAN 16 SPECIFICATIONS 08 ELECTRICAL CONNECTIONS 16 SMART BY BOND 10 FINISHING THE INSTALLATION WARNING: Read and follow these instructions care
GENERAL INSTALLATION & OPERATION INSTRUCTIONS 1 To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning. 2 To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring. All electrical connections must be made in accordance with local codes, ordinances and/or the National Electric Code.
IMPORTANT SAFETY PRECAUTIONS WARNINGS: • Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting. • Support directly from building structure. • To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked "acceptable for fan support" and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced.
UNPACKING YOUR FAN UNPACK YOUR FAN AND CHECK THE CONTENTS. • Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing. Remove all parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged. • Examine all parts.
PREPARATION PREPARATION: Verify you have all parts before beginning the installation. Check foam insert closely for missing parts. Remove motor from packing. To avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor box. DO NOT LAY MOTOR HOUSING ON ITS SIDE AS THIS COULD RESULT IN SHIFTING OF MOTOR IN DECORATIVE ENCLOSURE.
HANGING THE FAN 1 2 Remove ball from downrod by loosening set screw in the side of the ball. Slide ball down and remove ball pin; remove ball. (Fig. 1) Carefully support fan body (motor) in its styrofoam packing with the mounting collar (where the wires come out) facing upward. 3 Loosen the two security set screws and remove the downrod pin instead of hitch pin from the coupling on top of the motor assembly. (Fig.
REMEMBER to turn off the power before you begin. Safety Cable To properly install your ceiling fan, follow the steps below. 6 7 8 9 Ball Moisture Cap Slip the yoke cover, trim ring and canopy onto the downrod. (Fig. 3) Cross Pin Slide the hanger ball onto the downrod, insert the cross pin through the downrod and tighten. Tighten the set screw. Hanger Ball Ground Wire Hook-up (3) Wires Feed wires through holes in rubber ball moisture cap and slide cap down over top of ball. (Fig.
ELECTRICAL CONNECTIONS ELECTRICAL CONNECTIONS: Be sure electricity is turned off at the main power box before wiring. 1 OUTLET BOX Disconnect the power and remove the existing wall plate and switch from the wall junction box. (Fig. 1) SWITCH SCREWS WALL PLATE SCREWS WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse or breaker box before wiring.
Connect the black wire from the switch to the black wire from the wall outlet box. BLACK 3 2 Connect second black wire from switch to the black wire from the wall outlet box feeding to fan installation. 3 Connect the yellow/green striped wire form the switch to the ground terminal on the wall outlet box. 1 BLACK BLACK 2 Ground Conductor Outlet Box 4 WHITE GREEN 1 BLACK b. Connecting the wires from the wall switch to the wires from the wall outlet box. (Fig.
FINISHING THE INSTALLATION 1 Tuck connections neatly into ceiling outlet box. 2 Slide the canopy up to mounting bracket and place the key hole on the canopy over the screw on the mounting bracket, turn canopy until it locks in place at the narrow section of the key holes. 3 Ceiling Fan Outlet Box Hanger Bracket Align the circular hole on canopy with the remaining hole on the mounting bracket, secure by tightening the two set screws.
INSTALLATION OF THE BLADES Blade Arm Screw & rubber washer Blade 1 Place blade over blade arm and align blade with mounting holes in blade arms. Repeat this procedure without tightening the screw until all 3 screws and nuts have been started into the blade arm (Fig. 1). 2 Tighten each screw starting with center screw. 3 Fasten blade assembly to motor with provided screws and lock lockwashers by uses Blade Arm Wrench. (Fig. 1) Repeat procedure for remaining blades.
INSTALLATION OF LOWER COVER NOTE: Mounting Hub Lower Cover 12 | hinkley.com Be sure the power is off before installing. 1 Attach the lower cover to the mounting hub by turn the cover clockwise until tight. 2 Turn the power on.
OPERATION Restore power to ceiling fan and test for properoperation. The fan 4-speed control is used to set the fan speed as follows: = Turns the fan off 1 = High Speed 2 = Medium High Speed 3 = Medium Speed 4 = Low Speed Speed settings for warm or cool weather depend on factors such as the room size, ceiling height, number of fans, etc. 4 3 2 1 ©2019 Hinkley Lighting, Inc. | hinkley.
Summer Mode and Winter Mode Operation 1 IMPORTANT: To prevent damage or cause injury, be sure that fan is switched to off and blades have stopped moving completely before attempting to change direction of rotation. 2 The reverse switch is located on the top of the motor housing. Slide the switch to the right for winter mode operation. Slide the switch to the left for summer mode operation. Make sure switch is not stuck between forward and reverse positions.
CARE AND CLEANING Periodically it may be necessary to re-tighten blade to blade arm screws or blade arm to motor screws to prevent clicking or humming sound during operation. This is especially true in climates with broad temperature and humidity ranges. When dusting the blades, you must support the blade to prevent bending - no pressure should be applied to the blades. If you experience any flaws in the operation of your fan, please check the following points.
ENERGY GUIDE SPECIFICATIONS AVERAGE PERFORMANCE AND ENERGY INFORMATION Estimated Yearly Energy Cost $11 $3 PERFORMANCE SPECIFICATIONS Airflow 4,465 Cubic Feet Per Minute $34 Cost Range of Similar Models (19” – 84”) • The higher the airflow, the more air the fan will move • Airflow Efficiency: 115 Cubic Feet Per Minute Per Watt • Based on 12 cents per kWh and 6.
HINKLEY IS PROUD TO PROVIDE YOU WITH CEILING FAN PRODUCTS THAT ENHANCE YOUR SPACE WITH COMFORT, PURPOSE AND STYLE. AS A FAMILY COMPANY, WE ARE COMMITTED TO DESIGN, PERFORMANCE AND QUALITY, AND WHAT’S IMPORTANT TO YOU IS PARAMOUNT TO US. FOR A COMPLETE ASSORTMENT OF OUR PRODUCTS AND SOURCE BOOKS, VISIT HINKLEY.COM.
INSTALLATION OF SAFETY CABLE SUPPORT Attach the wood screw and the flat washer to the ceiling joist as shown (do not fully tighten). Slide the cable clamp onto the safety cable from the fan. Loop the safety cable around the wood screw that was just attached to ceiling joist. Feed the end of the cable into the clamp and pull as much cable through as possible. Firmly tighten screw in the clamp. Cut off excess cable.
GLOBAL HEADQUARTERS 33000 Pin Oak Parkway | Avon Lake, Ohio 44012 T (440) 653 5500 | F (440) 653 5555 | hinkley.
72" INDY ™ VENTILADOR LED INTERIOR / EXTERIOR DC WET MANUAL DE INSTRUCCIONES EN ESPAÑOL
QUEREMOS QUE AMES A TU NUEVO VENTILADOR ASÍ QUE ESTAMOS AQUÍ SI TIENE UNA PREGUNTA, NECESITA AYUDA O QUIERE HABLAR SOBRE NUESTROS PRODUCTOS. ENVÍE SUGERENCIAS NUESTRO CAMINO TAMBIÉN: SIEMPRE ESTAMOS BUSCANDO HACER QUE SU EXPERIENCIA CON HINKLEY SEA POSITIVA. > SERVICE@HINKLEY.COM > 800.HINKLEY > VAMOS A ESE ESTILO HINKLEY@HINKLEY #HINKLEYSTYLE Este manual contiene instrucciones completas para la instalación y operación de este ventilador.
Tabla de contenido 02 INSTRUCCIONES GENERALES DE INSTALACIÓN Y OPERACIÓN 11 ACCESORIO DE HOJA 03 PRECAUCIONES IMPORTANTES DE SEGURIDAD 12 INSTALACIÓN DE LA CUBIERTA INFERIOR 03 HERRAMIENTAS Y MATERIALES REQUERIDOS 13 OPERACIÓN 04 DESEMBALAJE TU VENTILADOR 15 CUIDADO Y LIMPIEZA 05 PREPARACIÓN 15 SOLUCIÓN DE PROBLEMAS 05 INSTALANDO EL SOPORTE COLGANTE 16 GUÍA DE ENERGÍA 06 COLGANDO EL VENTILADOR 16 ESPECIFICACIONES 08 CONEXIONES ELÉCTRICAS 16 INTELIGENTE POR BONO 10 ACABADO DE
INSTRUCCIONES GENERALES DE INSTALACIÓN Y OPERACIÓN 1 2 Para garantizar el éxito de la instalación, asegúrese de leer las instrucciones y revisar los diagramas a fondo antes de comenzar Para evitar posibles descargas eléctricas, asegúrese de que la electricidad esté apagada en la caja de alimentación principal antes de realizar el cableado. Todas las conexiones eléctricas deben realizarse de acuerdo con los códigos, ordenanzas locales y / o el Código Eléctrico Nacional.
PRECAUCIONES IMPORTANTES DE SEGURIDAD ADVERTENCIAS: • Desconecte la energía quitando el fusible o apagando el interruptor de circuito antes de instalar el ventilador y / o la iluminación opcional. • Apoyo directo desde la estructura del edificio. • Para reducir el riesgo de incendio, descarga eléctrica o lesiones personales, monte en la caja de salida marcada como "aceptable para soporte del ventilador" y use los tornillos de montaje provistos con la caja de salida.
DESEMBALAJE TU VENTILADOR DESEMBALA TU VENTILADOR Y COMPRUEBA EL CONTENIDO • No deseche la caja de cartón. Si alguna vez es necesario reemplazar o reparar la garantía, el ventilador debe devolverse en su embalaje original. Retire todas las piezas y hardware. No coloque la carcasa del motor sobre un costado, o la carcasa decorativa puede moverse, doblarse o dañarse. • Examinar todas las partes.
PREPARACIÓN PREPARACIÓN: Verifique que tenga todas las piezas antes de comenzar la instalación. Revise el inserto de espuma de cerca por si faltan piezas. Retire el motor de la empaquetadura. Para evitar daños en el acabado, ensamble el motor sobre una superficie acolchada suave o use el inserto de espuma original en la caja del motor. NO COLOQUE LA VIVIENDA DEL MOTOR EN SU LADO ya QUE ESTO PODRÍA RESULTAR EN EL CAMBIO DEL MOTOR EN UNA CUBIERTA DECORATIVA.
COLGANDO EL VENTILADOR 1 2 3 4 5 Retire la bola de la varilla aflojando el tornillo de fijación en el costado de la bola. Deslice la bola hacia abajo y retire el pasador; quitar la pelota (Figura 1) Pin cruzado Sostenga con cuidado el cuerpo del ventilador (motor) en su embalaje de espuma de poliestireno con el collar de montaje (de donde salen los cables) hacia arriba.
RECUERDA apagar la corriente antes de comenzar. Para instalar correctamente su ventilador de techo, siga los pasos a continuación. 6 Deslice la cubierta del yugo, el anillo de ajuste y el dosel sobre la varilla. (Fig. 3) 7 Deslice la bola de suspensión en la varilla, inserte el pasador transversal a través de la varilla y apriete. Apriete el tornillo de fijación.
CONEXIONES ELÉCTRICAS CONEXIONES ELÉCTRICAS: Asegúrese de que la electricidad esté apagada en la caja de alimentación principal antes de realizar el cableado. 1 CAJA DE SALIDA Desconecte la alimentación y retire la placa de pared existente y cambie de la caja de conexiones de pared.
Conecte el segundo cable negro del interruptor al cable negro de la caja de salida de pared que alimenta a la instalación del ventilador. 3 Conecte el cable rayado amarillo / verde del interruptor al terminal de tierra en la caja de toma de corriente. Negra 3 2 1 Verde 2 Conductor de tierra Caja de salida 4 Negra Blanca Conecte el cable negro del interruptor al cable negro de la caja de toma de corriente.
ACABADO DE LA INSTALACIÓN 1 2 3 Meta las conexiones cuidadosamente en la caja de salida del techo. Deslice la cubierta hacia el soporte de montaje y coloque el orificio de la llave en la cubierta sobre el tornillo del soporte de montaje, gire la cubierta hasta que encaje en su lugar en la sección estrecha de los agujeros de la llave. Alinee el orificio circular en el dosel con el orificio restante en el soporte de montaje, asegure apretando los dos tornillos de fijación.
INSTALACIÓN DE LAS CUCHILLAS Tornillo y arandela de goma Brazo de la cuchilla Espada Nuez Fig. 1 1 Coloque la cuchilla sobre el brazo de la cuchilla y alinee la cuchilla con los agujeros de montaje en los brazos de la cuchilla. Repita este procedimiento sin apretar el tornillo hasta que los 3 tornillos y tuercas hayan comenzado en el brazo de la cuchilla (Fig. 1). 2 Apriete cada tornillo comenzando con el tornillo central.
INSTALACIÓN DE LA CUBIERTA INFERIOR NOTA: Asegúrese de que la energía esté apagada antes de instalar. 1 Fije la cubierta inferior al cubo de montaje girando la tapa en sentido horario hasta que quede apretada. 2 Encienda la corriente. ¡Su ventilador de techo Hinkley ya está listo para disfrutar! 2 Cubo de montaje Cubierta inferior 12 | hinkley.
OPERACIÓN Restaure la energía al ventilador de techo y pruebe la operación correcta. El control de 4 velocidades del ventilador se utiliza para configurar la velocidad del ventilador de la siguiente manera: = Apaga el ventilador o ff 1 = alta velocidad 2 = velocidad media alta 3 = velocidad media 4 = baja velocidad Los ajustes de velocidad para clima cálido o frío dependen de factores como el tamaño de la habitación, la altura del techo, la cantidad de ventiladores, etc.
Modo verano y funcionamiento en modo invierno 1 2 IMPORTANTE: Para evitar daños o causar lesiones, asegúrese de que el ventilador esté apagado y las aspas hayan dejado de moverse por completo antes de intentar cambiar la dirección de rotación. El interruptor de inversión se encuentra en la parte superior de la carcasa del motor. Deslice el interruptor hacia la derecha para la operación en modo invierno. Deslice el interruptor hacia la izquierda para la operación en modo verano.
CUIDADO Y LIMPIEZA Periódicamente puede ser necesario volver a apretar los tornillos de la cuchilla al brazo de la cuchilla o del brazo de la cuchilla a los tornillos del motor para evitar que se escuche un clic o un zumbido durante el funcionamiento. Esto es especialmente cierto en climas con amplios rangos de temperatura y humedad. Cuando desempolve las cuchillas, debe sostener la cuchilla para evitar que se doble; no se debe aplicar presión a las cuchillas.
ESPECIFICACIONES GUÍA DE ENERGÍA INFORMACIÓN MEDIA DE DESEMPEÑO Y ENERGÍA ESPECIFICACIONES DE RENDIMIENTO Estimated Yearly Energy Cost $5 $3 $34 Cost Range of Similar Models (19” – 84”) Airflow 3,597 ALTA VELOCIDAD BAJA VELOCIDAD Flujo de aire (CFM) 6425 2244 Cubic Feet Per Minute Energía usada (vations) 62.6 11.
HINKLEY SE ENCUENTRA ORGULLOSO DE PROPORCIONARLE PRODUCTOS PARA VENTILADORES DE TECHO QUE MEJORAN SU ESPACIO CON COMODIDAD, PROPÓSITO Y ESTILO. COMO EMPRESA FAMILIAR, ESTAMOS COMPROMETIDOS CON EL DISEÑO, EL RENDIMIENTO Y LA CALIDAD, Y LO QUE ES IMPORTANTE PARA USTED ES PARAMOUNT PARA NOSOTROS. PARA UN SURTIDO COMPLETO DE NUESTROS PRODUCTOS Y FUENTES DE LIBROS, VISITA HINKLEY.COM.
INSTALACIÓN DE SEGURIDAD SOPORTE DE CABLE Fije el tornillo para madera y la arandela plana a la viga del techo como se muestra (no apriete completamente). Deslice la abrazadera del cable sobre el cable de seguridad desde el ventilador. Pase el cable de seguridad alrededor del tornillo de madera que se acaba de conectar a la viga del techo. Introduzca el extremo del cable en la abrazadera y pase la mayor cantidad de cable posible. Apriete firmemente el tornillo en la abrazadera. Cortar el exceso de cable.
GLOBAL HEADQUARTERS 33000 Pin Oak Parkway | Avon Lake, Ohio 44012 T (440) 653 5500 | F (440) 653 5555 | hinkley.
72" INDY ™ VENTILATEUR LED INTÉRIEUR / EXTÉRIEUR DC WET MANUEL D'INSTRUCTIONS POUR VENTILATEUR DE PLAFOND EN FRANÇAIS
NOUS VOULONS VOUS AIMER VOTRE NOUVEAU FAN NOUS SOMMES ICI SI VOUS AVEZ UNE QUESTION, BESOIN D'UNE AIDE OU VOULEZ CHAT SUR NOS PRODUITS. ENVOYER DES SUGGESTIONS NOTRE FAÇON AUSSI - NOUS CHERCHONS TOUJOURS À FAIRE DE VOTRE EXPÉRIENCE AVEC HINKLEY UNE POSITIVE. > SERVICE@HINKLEY.COM > 800.HINKLEY > LET’S SEE THAT HINKLEY STYLE @HINKLEY #HINKLEYSTYLE Ce manuel contient des instructions complètes pour l'installation et le fonctionnement de ce ventilateur.
TABLE DES MATIÈRES 02 INSTRUCTIONS GÉNÉRALES D'INSTALLATION ET DE FONCTIONNEMENT 11 ATTACHEMENT DE LAME 03 PRÉCAUTIONS DE SÉCURITÉ IMPORTANTES 12 INSTALLATION DU COUVERCLE INFÉRIEUR 03 OUTILS ET MATÉRIAUX REQUIS 13 OPÉRATION 04 DÉBALLAGE DE VOTRE VENTILATEUR 15 ENTRETIEN ET NETTOYAGE 05 PRÉPARATION 15 DÉPANNAGE 05 INSTALLATION DU SUPPORT DE SUSPENSION 16 GUIDE ÉNERGÉTIQUE 06 ACCROCHER LE VENTILATEUR 16 CARACTÉRISTIQUES 08 CONNECTIONS ELECTRIQUES 16 SMART BY BOND 10 FIN DE L
INSTRUCTIONS GÉNÉRALES D'INSTALLATION ET DE FONCTIONNEMENT 1 2 3 4 5 Pour assurer le succès de l'installation, assurez-vous de lire les instructions et de lire attentivement les schémas avant de commencer. Pour éviter tout choc électrique, assurez-vous que l'électricité est coupée sur le boîtier d'alimentation principal avant le câblage. Toutes les connexions électriques doivent être effectuées conformément aux codes locaux, aux ordonnances et / ou au National Electric Code.
PRÉCAUTIONS DE SÉCURITÉ IMPORTANTES AVERTISSEMENTS: • Coupez l'alimentation en retirant le fusible ou en fermant le disjoncteur avant d'installer le ventilateur et / ou l'éclairage en option. • Support directement à partir de la structure du bâtiment. • Pour réduire le risque d'incendie, d'électrocution ou de blessure, montez sur la boîte de sortie marquée "acceptable pour le support du ventilateur" et utilisez les vis de montage fournies avec la boîte de sortie.
DÉBALLAGE DE VOTRE VENTILATEUR DÉBALLER VOTRE FAN ET VÉRIFIER LE CONTENU • Ne jetez pas le carton. Si un remplacement ou une réparation sous garantie est nécessaire, le ventilateur doit être retourné dans son emballage d'origine. Retirez toutes les pièces et le matériel. Ne posez pas le boîtier du moteur sur le côté, sinon le boîtier décoratif pourrait se déplacer, être plié ou endommagé. • Examinez toutes les pièces.
PRÉPARATION : PRÉPARATION: Vérifiez que vous disposez de toutes les pièces avant de commencer l'installation. Vérifiez soigneusement l'insert en mousse pour les pièces manquantes. Retirez le moteur de l'emballage. Pour éviter d'endommager la fi nition, assemblez le moteur sur une surface rembourrée ou utilisez l'insert en mousse d'origine dans le boîtier du moteur. NE POSEZ PAS DE LOGEMENT DE MOTEUR SUR LE CÔTÉ, CELA POURRAIT ENTRAÎNER LE DÉPLACEMENT DU MOTEUR DANS LE BOÎTIER DÉCORATIF.
ACCROCHER LE VENTILATEUR 1 2 3 4 5 Retirez la balle de la tige de suspension en desserrant la vis de réglage sur le côté de la balle. Faites glisser la balle vers le bas et retirez la goupille; retirer la balle. (Fig. 1) Soutenez soigneusement le corps du ventilateur (moteur) dans son emballage en mousse de polystyrène avec le collier de montage (où les fils sortent) vers le haut.
N'OUBLIEZ PAS de couper l'alimentation avant de commencer. Pour installer correctement votre ventilateur de plafond, suivez les étapes ci-dessous. 6 Glissez le couvercle de l'étrier, l'anneau de garniture et la verrière sur la tige de suspension. (Fig.3) 7 Faites glisser la boule de suspension sur la tige de suspension, insérez la goupille transversale à travers la tige de suspension et serrez. Serrez la vis de réglage.
CONNECTIONS ELECTRIQUES CONNEXIONS ÉLECTRIQUES: Assurez-vous que l'électricité est coupée au niveau de la boîte d'alimentation principale avant le câblage. 1 BOÎTE DE SORTIE COMMUTATEUR PLAQUE MURALE DES VIS Débranchez l'alimentation et retirez la plaque murale et l'interrupteur existants de la boîte de jonction murale. (Fig. 1) DES VIS AVERTISSEMENT: Pour éviter tout choc électrique, assurez-vous que l'électricité est coupée au niveau du fusible principal ou du disjoncteur avant le câblage.
3 3 2 1 VERT Connectez le deuxième fil noir de l'interrupteur au fil noir de la boîte de sortie murale alimentant l'installation du ventilateur. Connectez le fil rayé jaune / vert du commutateur à la borne de terre du boîtier de prise murale. Conducteur de terre Boîte de sortie 4 NOIR BLANC 2 Connectez le fil noir de l'interrupteur au fil noir de la prise murale. NOIR 1 NOIR NOIR b. Connexion des fils de l'interrupteur mural aux fils du boîtier de prise murale. (Fig.
FIN DE L'INSTALLATION 1 2 3 Rentrez soigneusement les connexions dans la boîte de sortie au plafond. Faites glisser la verrière jusqu'au support de montage et placez le trou de clé sur la verrière sur la vis du support de montage, tournez la verrière jusqu'à ce qu'elle se verrouille en place dans la section étroite des trous de clé. Alignez le trou circulaire sur la verrière avec le trou restant sur le support de montage, fixez en serrant les deux vis de réglage.
INSTALLATION DES LAMES 1 Vis et rondelle en caoutchouc Bras de lame Lame Écrou 2 Serrez chaque vis en commençant par la vis centrale. 3 Fixez l'assemblage de la lame au moteur avec les vis fournies et verrouillez les rondelles de blocage en utilisant une clé pour bras de lame. (Fig. 1) Répétez la procédure pour les lames restantes. Assurez-vous que les vis sont SERRÉES! Des vis de moteur desserrées peuvent contribuer à un ronflement inutile pendant le fonctionnement. (Fig.
INSTALLATION DU COUVERCLE INFÉRIEUR REMARQUE: assurez-vous que l'alimentation est coupée avant d'installer Moyeu de montage Couvercle inférieur 12 | hinkley.com 1 Fixez le couvercle inférieur au moyeu de montage à tour de rôle le couvercle dans le sens horaire jusqu'à ce qu'il soit serré. 2 Mettez l'appareil sous tension.
OPÉRATION Rétablissez l'alimentation du ventilateur de plafond et testez son bon fonctionnement. La commande du ventilateur à 4 vitesses est utilisée pour régler la vitesse du ventilateur comme suit: = Éteint le ventilateur ff 1 = haute vitesse 2 = vitesse moyenne élevée 3 = vitesse moyenne 4 = basse vitesse Les réglages de vitesse par temps chaud ou froid dépendent de facteurs tels que la taille de la pièce, la hauteur du plafond, le nombre de ventilateurs, etc. 4 3 2 1 ©2019 Hinkley Lighting, Inc.
Fonctionnement en mode été et en mode hiver 1 IMPORTANT: pour éviter des dommages ou des blessures, assurez-vous que le ventilateur est réglé sur o ff et que les pales se sont complètement arrêtées avant d'essayer de changer le sens de rotation. 2 L'interrupteur de marche arrière est situé sur le dessus du boîtier du moteur. Faites glisser le commutateur vers la droite pour le fonctionnement en mode hiver. Faites glisser le commutateur vers la gauche pour le fonctionnement en mode été.
ENTRETIEN ET NETTOYAGE Périodiquement, il peut être nécessaire de resserrer les vis de la lame sur le bras de la lame ou du bras de la lame sur les vis du moteur pour éviter les cliquetis ou les bourdonnements pendant le fonctionnement. Cela est particulièrement vrai dans les climats avec de larges plages de température et d'humidité. Lors de l'époussetage des lames, vous devez soutenir la lame pour éviter qu'elle ne se plie - aucune pression ne doit être appliquée sur les lames.
GUIDE ÉNERGÉTIQUE CARACTÉRISTIQUES PERFORMANCE MOYENNE ET INFORMATIONS ÉNERGÉTIQUES SPÉCIFICATIONS DE PERFORMANCE Estimated Yearly Energy Cost $11 $3 Airflow 4,465 Cubic Feet Per Minute $34 Cost Range of Similar Models (19” – 84”) • The higher the airflow, the more air the fan will move • Airflow Efficiency: 115 Cubic Feet Per Minute Per Watt • Based on 12 cents per kWh and 6.
HINKLEY EST FIÈRE DE VOUS FOURNIR DES PRODUITS DE VENTILATEUR DE PLAFOND QUI AMÉLIORENT VOTRE ESPACE AVEC CONFORT, OBJECTIF ET STYLE. EN TANT QU'ENTREPRISE FAMILIALE, NOUS NOUS ENGAGEONS À CONCEVOIR, PERFORMANCE ET QUALITÉ, ET CE QUI EST IMPORTANT POUR VOUS EST PARAMOUNT POUR NOUS. POUR UN ASSORTIMENT COMPLET DE NOS PRODUITS ET LIVRES DE SOURCE, VISITEZ HINKLEY.COM.
INSTALLATION DE LA SÉCURITÉ SUPPORT DE CÂBLE Fixez la vis à bois et la rondelle plate à la solive de plafond comme illustré (ne serrez pas complètement). Faites glisser le serre-câble sur le câble de sécurité du ventilateur. Enroulez le câble de sécurité autour de la vis à bois qui vient d'être fixée à la solive de plafond. Insérez l'extrémité du câble dans la pince et tirez le plus de câble possible. Serrez fermement la vis du collier. Coupez l'excédent de câble.
GLOBAL HEADQUARTERS 33000 Pin Oak Parkway | Avon Lake, Ohio 44012 T (440) 653 5500 | F (440) 653 5555 | hinkley.