60" HOVER™ INDOOR / OUTDOOR LED FAN DC WET DC MOTOR LED CEILING FAN INSTRUCTION MANUAL
WE WANT YOU TO LOVE YOUR NEW FAN SO WE’RE HERE IF YOU HAVE A QUESTION, NEED SOME HELP OR WANT TO CHAT ABOUT OUR PRODUCTS. SEND SUGGESTIONS OUR WAY TOO—WE’RE ALWAYS LOOKING TO MAKE YOUR EXPERIENCE WITH HINKLEY A POSITIVE ONE. > SERVICE@HINKLEY.COM > 800.HINKLEY > LET’S SEE THAT HINKLEY STYLE @HINKLEY #HINKLEYSTYLE This manual contains complete instructions for the installation and operation of this fan. It has been designed to make the installation process as easy as possible.
TABLE OF CONTENTS 02 GENERAL INSTALLATION & OPERATING INSTRUCTIONS 11 INSTALLING THE LIGHT KIT AND GLASS SHADE 03 IMPORTANT SAFETY PRECAUTIONS 12 INSTALLING THE WALL CONTROL 03 TOOLS & MATERIALS REQUIRED 13 OPERATION 04 UNPACKING YOUR FAN 15 CARE AND CLEANING 05 PREPARATION 15 TROUBLESHOOTING 05 INSTALLING THE HANGING BRACKET 16 ENERGY GUIDE 06 HANGING THE FAN 16 SPECIFICATIONS 08 ELECTRICAL CONNECTIONS 16 SMART BY BOND 09 FINISHING THE INSTALLATION 10 BLADE ATTACHMENT WA
GENERAL INSTALLATION & OPERATION INSTRUCTIONS 1 To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning. 2 To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring. All electrical connections must be made in accordance with local codes, ordinances and/or the National Electric Code.
IMPORTANT SAFETY PRECAUTIONS WARNINGS: • Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting. • Support directly from building structure. • To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked "acceptable for fan support" and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced.
UNPACKING YOUR FAN UNPACK YOUR FAN AND CHECK THE CONTENTS. • Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing. Remove all parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged. • Examine all parts.
PREPARATION PREPARATION: Verify you have all parts before beginning the installation. Check foam insert closely for missing parts. Remove motor from packing. To avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor box. Canopy Downrod Yoke Cover Motor Housing DO NOT LAY MOTOR HOUSING ON ITS SIDE AS THIS COULD RESULT IN SHIFTING OF MOTOR IN DECORATIVE ENCLOSURE. LED Light Kit Blade Parts identification on assembled fan.
HANGING THE FAN 1 Remove ball from downrod by loosening set screw in the side of the ball. Slide ball down and remove ball pin; remove ball. (Fig. 1) 2 Carefully support fan body (motor) in its styrofoam packing with the mounting collar (where the wires come out) facing upward. 3 Loosen the two security set screws and remove the downrod pin and retaining clip from the coupling on top of the motor assembly. (Fig. 2) 4 Carefully feed the electrical lead wires from the fan through the downrod.
REMEMBER to turn off the power before you begin. To properly install your ceiling fan, follow the steps below. Ball Moisture Cap 6 Slip the yoke cover, trim ring and canopy onto the downrod. (Fig. 3) Cross Pin 7 Slide the hanger ball onto the downrod, insert the cross pin through the downrod and tighten. Tighten the set screw. Hanger ball 8 Feed wires through holes in rubber ball moisture cap and slide cap down over top of ball. (Fig. 3) 9 Lift ball/downrod/fan into hanger bracket opening.
ELECTRICAL CONNECTIONS REMEMBER -Turn off the power! NOTE - Control must be installed within 30 feet of fan. Use the wire nuts supplied with your fan when making connections. Secure the connectors with electrical tape and make sure there are no loose connections or wire strands. BLK (AC IN) WH (AC IN) Make wire connections from the fan to the receiver unit. For this step use the bundle of 5 wires on the receiver. (Fig.
FINISHING THE INSTALLATION 1 Tuck connections neatly into ceiling outlet box. 2 Slide the canopy up to mounting bracket and place the key hole on the trim ring the screw on the mounting bracket, turn canopy until it locks in place at the narrow section of the key holes. 3 Ceiling Fan Outlet Box Hanger Bracket Align the circular hole on canopy with the remaining hole on the mounting bracket, secure by tightening the two set screws.
BLADE ATTACHMENT Fasten blade to motor with provided screws, lock washers and flat washers. Repeat procedure for remaining blades. Make sure screws are TIGHT! Loose motor screws can contribute to unnecessary hum during operation. NOTE: Cordless power screwdrivers are NOT recommended, as they usually strip the heads of the screws and usually will not fully compress the lock washers on the motor screws. Use a large flat blade screwdriver for final tightening to fully compress the washers.
INSTALLING THE LED ASSEMBLY AND GLASS SHADE Wire connectors Mounting plate Mounting Hub (bottom of motor) Mounting plate LED Assembly Light Wires Screws Screws Glass shade Fig. 1 Fig. 2 NOTE: Be sure the power is off before installing. 1 Remove one of the three screws on the mounting hub located on the fan motor. Loosen the other 2 screws. (Do not remove) (Fig. 1) 2 Pass the light wires through the center hole of the mounting plate.
INSTALLING THE WALL CONTROL REMEMBER to turn off the power before you begin. NOTE - Control must be installed within 30 feet of fan. 1 Remove the existing wall plate and the old switch from the wall outlet box. (Fig. 1) 2 Connect the wiring from the wall switch receptacle to wall transmitter unit Connect one BLACK wire from the wall to one BLACK wire (labeled "TO FAN") from the wall transmitter.
OPERATION Your DC brushless motor is equipped with an automatically learned type remote control. There is no frequency switches on the receiver or transmitter. The fan can start to use once the pairing process is done. Remove the panel from the transmitter and then install one 23A/12V battery (included). To prevent damage to transmitter, remove the battery if not use for long periods of time (Fig. 16).
Summer Mode and Winter Mode Operation 8 Summer Mode (forward): A DOWNWARD airflow creates a cooling effect as shown in Figure 3. This allows you to set your air conditioner on a warmer setting without affecting your comfort. 9 Winter Mode (Reverse): An UPWARD airflow moves warmer air off the ceiling area as shown in Figure 4. This allows you to set your heating unit on a cooler setting without affecting your comfort. SUMMER MODE (COUNTERCLOCKWISE DIRECTION) Fig. 3 14 | hinkley.
CARE AND CLEANING Periodically it may be necessary to re-tighten blade to blade arm screws or blade arm to motor screws to prevent clicking or humming sound during operation. This is especially true in climates with broad temperature and humidity ranges. When dusting the blades, you must support the blade to prevent bending - no pressure should be applied to the blades. If you experience any flaws in the operation of your fan, please check the following points.
ENERGY GUIDE SPECIFICATIONS AVERAGE PERFORMANCE AND ENERGY INFORMATION Estimated Yearly Energy Cost $5 $3 $34 Cost Range of Similar Models (19” – 84”) PERFORMANCE SPECIFICATIONS HIGH SPEED LOW SPEED Airflow (CFM) 7118 1989 Cubic Feet Per Minute Energy Use (Watts) 28.5 2.1 • The higher the airflow, the more air the fan will move • Airflow Efficiency: 267 Cubic Feet Per Minute Per Watt Airflow Efficiency (CFM/W) 249 961 Energy Costs (Yearly) $8 $1 Amps 0.37 0.
HINKLEY IS PROUD TO PROVIDE YOU WITH CEILING FAN PRODUCTS THAT ENHANCE YOUR SPACE WITH COMFORT, PURPOSE AND STYLE. AS A FAMILY COMPANY, WE ARE COMMITTED TO DESIGN, PERFORMANCE AND QUALITY, AND WHAT’S IMPORTANT TO YOU IS PARAMOUNT TO US. FOR A COMPLETE ASSORTMENT OF OUR PRODUCTS AND SOURCE BOOKS, VISIT HINKLEY.COM.
GLOBAL HEADQUARTERS 33000 Pin Oak Parkway | Avon Lake, Ohio 44012 T (440) 653 5500 | F (440) 653 5555 | hinkley.
