ICC ESR-2269 for X-U Universal and X-P Concrete Powder Driven Fasteners

ManualsBrandsHilti ManualsDirect FasteningX-P P8 Universal nails

Table Of Contents

ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed

as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as

to any finding or other matter in this report, or as to any product covered by the report.

ICC-ES Evaluation Report

ESR-2269

Reissued February 2021

This report is subject to renewal February 2023.

www.icc-es.org | (800) 423-6587 | (562) 699-0543 A Subsidiary of the International Code Council

DIVISION: 03 00 00—CONCRETE

Section: 03 15 00—Concrete Accessories

Section: 03 16 00—Concrete Anchors

DIVISION: 04 00 00—MASONRY

Section: 04 05 19.16—Masonry Anchors

DIVISION: 05

00 00—METALS

Section: 05 05 23—Metal Fastenings

DIVISION: 06

00 00—WOOD, PLASTICS AND

COMPOSITES

Section: 06 05 23—Wood, Plastic, and Composite

Fastenings

REPORT HOLDER:

HILTI, INC.

EVALUATION SUBJECT:

HILTI LOW-VELOCITY X-U AND X-U 15 UNIVERSAL

FASTENERS AND X-P CONCRETE FASTENERS

1.0 EVALUATION SCOPE

Compliance with the following codes:

 2018, 2015, and 2012 International Building Code

(IBC)

 2018, 2015, and 2012 International Residential Code

(IRC)

For evaluation for compliance with codes adopted by the

Los Angeles Department of Building and Safety (LADBS),

see ESR-2269 LABC and LARC Supplement.

Property evaluated:

Structural

2.0 USES

2.1 General:

The Hilti X-U and X-P power-actuated fasteners (PAFs) are

used to attach wood, light gage steel, and other building

elements to base materials of normalweight concrete, sand-

lightweight concrete, steel deck panels with sand-

lightweight concrete fill and concrete masonry. The X-U

fasteners are also used to attach building elements to steel

base materials. The Hilti X-U 15 fasteners are used to attach

light gage steel and other building elements to steel base

material. The fasteners are alternatives to the cast-in-place

anchors described in IBC Section 1901.3 (2012 IBC Section

1908; 2009 IBC Section 1911) for placement in concrete;

the embedded anchors described in Section 8.1.3 of TMS

402, referenced in Section 2107 of the IBC (Section 2.1.4 of

TMS 402-11 and -08 referenced in Section 2107 of the 2012

and 2009 IBC, respectively), for placement in masonry; and

the welds and bolts used to attach materials to steel,

described in IBC Sections 2204.1 and 2204.2, respectively.

For structures regulated under the IRC, the fasteners may

be used where an engineered design is submitted in

accordance with IRC Section R301.1.3.

2.2 Horizontal Diaphragms:

The Hilti X-U fasteners may be used as alternates to 10d

common nails for fastening wood structural panels to

structural steel members in horizontal diaphragms.

3.0 DESCRIPTION

3.1 Fasteners:

3.1.1 X-U: The X-U fasteners are powder-driven fasteners

made from hardened steel complying with the

manufacturer’s quality documentation, austempered to a

Rockwell C nominal hardness of 57.5 and zinc-plated in

accordance with ASTM B633 SC 1, Type III. The fasteners

have a shank diameter of 0.157 inch (4.0 mm), a head

diameter of 0.32 inch (8.2 mm) and a knurled tip, and come

in lengths ranging from 0.63 inch to 2.83 inches

(16 to 72 mm). See Figure 1 for the fastener configuration.

3.1.2 X-U 15: The X-U 15 fasteners are powder-driven

fasteners made from hardened steel complying with the

manufacturer’s quality documentation, austempered to a

Rockwell C nominal hardness of 59 and zinc plated in

accordance with ASTM B633 SC 1, Type III. The fasteners

have a shank diameter of 0.145 inch (3.7 mm), a head

diameter of 0.32 inch (8.2 mm) and a shank length of

0.63 inch (16 mm). See Figure 2 for the fastener

configuration.

3.1.3 X-P: The X-P fasteners are powder-driven fasteners

made from hardened steel complying with the

manufacturer’s quality documentation, austempered to a

Rockwell C nominal hardness of 59 and zinc plated in

accordance with ASTM B633 SC 1, Type III. The fasteners

have a shank diameter of 0.157 inch (4.0 mm), a head

diameter of 0.32 inch (8.2 mm) and come in lengths ranging

from 0.87 inch to 1.57 inches (22 to 40 mm). See Figure 3

for the fastener configuration.

3.2 Substrate Materials:

3.2.1 Concrete: Normal-weight and sand-lightweight

concrete must comply with IBC Chapter 19 or IRC Section

R402.2, as applicable. The minimum concrete compressive

strength at the time of fastener installation must be as noted

in the applicable allowable load table. Hollow core precast

concrete slabs must conform to the cross-sectional

dimensions shown in Figure 7.

Summary of content (13 pages)

PAGE 1
ESR-2269 ICC-ES Evaluation Report Reissued February 2021 This report is subject to renewal February 2023. www.icc-es.org | (800) 423-6587 | (562) 699-0543 DIVISION: 03 00 00—CONCRETE Section: 03 15 00—Concrete Accessories Section: 03 16 00—Concrete Anchors DIVISION: 04 00 00—MASONRY Section: 04 05 19.
PAGE 2
ESR-2269 | Most Widely Accepted and Trusted Page 2 of 13 3.2.2 Concrete Masonry: Concrete masonry units (CMUs) must be minimum 8-inch-thick (203 mm), and must comply with ASTM C90. Mortar must comply with ASTM C270. Grout must be coarse grout complying with ASTM C476. Concrete masonry walls must have a minimum compressive strength, f′m, of 1,500 psi (10.3 MPa). See Table 6 for applicable CMU density and mortar type.
PAGE 3
ESR-2269 | Most Widely Accepted and Trusted 4.1.6 Seismic Considerations: The Hilti fasteners are recognized for use when subjected to seismic loads as follows: 1. The Hilti fasteners may be used for attachment of nonstructural components listed in Section 13.1.4 of ASCE 7, which are exempt from the requirements of ASCE 7. 2.
PAGE 4
ESR-2269 | Most Widely Accepted and Trusted 5.4 For steel-to-steel connections that meet the applicability requirements of Section J5 of AISI S100-16, calculations demonstrating that the available connection strength has been determined in accordance with Section J5 of AISI S100-16 and Section 4.1.5 of this report, and equals to or exceeds the applied load, must be submitted to the code official.
PAGE 5
ESR-2269 | Most Widely Accepted and Trusted Page 5 of 13 TABLE 1—FASTENER DESCRIPTION AND APPLICATIONS FASTENER1 MAXIMUM MINIMUM SHANK HEAD POINT EFFECTIVE APPLICABLE APPLICABLE SHANK DIAMETER DIAMETER FASTENER LENGTH SHANK BASE LOAD TYPE [inch [inch COATING [inch LENGTH MATERIAL TABLES (mm)] (mm)] (mm)] [inch (mm)] FASTENER DESCRIPTION Steel 2, 7 Concrete 3, 4 Conc.-filled deck 5 CMU 6 Steel 2 Concrete 3 Conc.-filled deck 5 X-U ## Universal Knurled, Powder Actuated 0.157 (4.0) 0.
PAGE 6
ESR-2269 | Most Widely Accepted and Trusted Page 6 of 13 TABLE 3—ALLOWABLE LOADS FOR FASTENERS DRIVEN INTO NORMAL-WEIGHT CONCRETE1,2,4 MINIMUM SHANK FASTENER EMBEDMENT FASTENER DIAMETER DESCRIPTION DEPTH (inch) (inches) ALLOWABLE LOADS (lbf) Concrete Compressive Strength: 2500 psi Load Direction: Smooth Shank X-U 0.157 X-P 0.
PAGE 7
ESR-2269 | Most Widely Accepted and Trusted Page 7 of 13 TABLE 5—ALLOWABLE LOADS FOR FASTENERS DRIVEN INTO MINIMUM f′c = 3000 psi STRUCTURAL SAND-LIGHTWEIGHT CONCRETE WITH OR WITHOUT METAL DECK1,6 SHANK MINIMUM FASTENER FASTENER DIAMETER EMBEDMENT DESCRIPTION (inch) (inch) ALLOWABLE LOADS (lbf) Installed Through Metal Deck Panel into Concrete5 Installed into Concrete4 Fastener Location: 3-inch deep composite floor deck panel2 Tension Load Direction: Smooth Shank X-U X-P 0.157 0.
PAGE 8
ESR-2269 | Most Widely Accepted and Trusted Page 8 of 13 FIGURE 1—HILTI X-U FASTENER FIGURE 2—X-U 15 FASTENER FIGURE 3—X-P FASTENER FIGURE 4—HILTI FASTENER LOCATION IN 3-INCH-DEEP COMPOSITE FLOOR DECK PANEL, NORMAL DECK PANEL PROFILE ORIENTATION
PAGE 9
ESR-2269 | Most Widely Accepted and Trusted FIGURE 5—HILTI FASTENER LOCATION IN 11/2-INCH-DEEP COMPOSITE FLOOR DECK PANEL, NORMAL DECK PANEL PROFILE ORIENTATION FIGURE 6—HILTI FASTENER LOCATION IN 11/2-INCH-DEEP COMPOSITE FLOOR DECK PANEL, INVERTED DECK PANEL PROFILE ORIENTATION FIGURE 7—HILTI X-U FASTENER LOCATION IN HOLLOW-CORE CONCRETE SLABS Page 9 of 13
PAGE 10
ESR-2269 | Most Widely Accepted and Trusted FIGURE 8—WOOD STRUCTURAL PANEL DECK ATTACHMENT TO STEEL LEDGER WITH HILTI X-U UNIVERSAL POWDER DRIVEN FASTENER Page 10 of 13
PAGE 11
ICC-ES Evaluation Report ESR-2269 LABC and LARC Supplement Reissued February 2021 This report is subject to renewal February 2023. www.icc-es.org | (800) 423-6587 | (562) 699-0543 A Subsidiary of the International Code Council ® DIVISION: 03 00 00—CONCRETE Section: 03 15 00—Concrete Accessories Section: 03 16 00—Concrete Anchors DIVISION: 04 00 00—MASONRY Section: 04 05 19.
PAGE 12
ICC-ES Evaluation Report ESR-2269 FBC Supplement Reissued February 2021 This report is subject to renewal February 2023. www.icc-es.org | (800) 423-6587 | (562) 699-0543 A Subsidiary of the International Code Council ® DIVISION: 03 00 00—CONCRETE Section: 03 15 00—Concrete Accessories Section: 03 16 00—Concrete Anchors DIVISION: 04 00 00—MASONRY Section: 04 05 19.
PAGE 13
ESR-2269 FBC Supplement | Most Widely Accepted and Trusted Page 13 of 13 For products falling under Florida Rule 61G20-3, verification that the report holder’s quality assurance program is audited by a quality assurance entity approved by the Florida Building Commission for the type of inspections being conducted is the responsibility of an approved validation entity (or the code official, when the report holder does not possess an approval by the Commission).