Operating Instruction DSH 700X-900X
Table Of Contents
- Original operating instructions
- 1 Information about the documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Preparations at the workplace
- 5.1 Fuel
- 5.2 Assembly and adjustment
- 5.3 Locking rotary movement of the guide wheels
- 5.4 Mounting the gasoline-powered saw on the saw trolley (accessory)
- 5.5 Fitting the water pump (accessory)
- 5.6 Removing the water pump (accessory)
- 5.7 Starting the engine
- 5.8 Checks after starting the engine
- 5.9 Switching the engine off
- 6 Types of work
- 7 Care and maintenance
- 7.1 Maintenance table
- 7.2 Cleaning or replacing the air filter
- 7.3 Replacing a broken starter cord
- 7.4 Replacing the fuel filter
- 7.5 Cleaning the spark plug, setting the spark plug gap or replacing the spark plug
- 7.6 Adjusting the carburetor
- 7.7 Care and maintenance of the machine
- 7.8 Maintenance
- 7.9 Checks after care and maintenance work
- 8 Transport and storage
- 9 Troubleshooting
- 10 Disposal
- 11 Manufacturer’s warranty
- Mode d'emploi original
- 1 Indications relatives à la documentation
- 2 Sécurité
- 3 Description
- 4 Caractéristiques techniques
- 5 Préparatifs
- 5.1 Carburant
- 5.2 Travaux de montage et de réglage
- 5.3 Blocage du mouvement de rotation des roulettes de guidage
- 5.4 Montage de la tronçonneuse à essence sur le chariot de guidage (accessoire)
- 5.5 Montage de la pompe à eau (accessoire)
- 5.6 Démontage de la pompe à eau (accessoire)
- 5.7 Démarrage du moteur
- 5.8 Contrôles après démarrage du moteur
- 5.9 Arrêt du moteur
- 6 Travail
- 7 Nettoyage et entretien
- 7.1 Tableau d'entretien
- 7.2 Nettoyage ou remplacement du filtre à air
- 7.3 Remplacement du câble de démarrage sectionné
- 7.4 Remplacement du filtre carburant
- 7.5 Nettoyage de la bougie d'allumage, réglage de l'écartement des électrodes ou remplacement de la bougie d'allumage
- 7.6 Réglage du carburateur
- 7.7 Entretien de l'appareil
- 7.8 Entretien
- 7.9 Contrôle après des travaux de nettoyage et d'entretien
- 8 Transport et entreposage
- 9 Aide au dépannage
- 10 Recyclage
- 11 Garantie constructeur
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos técnicos
- 5 Preparación del trabajo
- 5.1 Combustible
- 5.2 Tareas de montaje y ajuste
- 5.3 Bloqueo del movimiento giratorio de los rodillos de guía
- 5.4 Instalación de la amoladora tronzadora de gasolina en el carro de guía (accesorio)
- 5.5 Montaje de la bomba de agua (accesorio)
- 5.6 Desmontaje de la bomba de agua (accesorio)
- 5.7 Arranque del motor
- 5.8 Comprobaciones después del arranque del motor
- 5.9 Desconexión del motor
- 6 Procedimiento de trabajo
- 7 Cuidado y mantenimiento
- 7.1 Tabla de mantenimiento
- 7.2 Limpieza o sustitución del filtro de aire
- 7.3 Sustitución del cable roto del arrancador
- 7.4 Sustitución del filtro de combustible
- 7.5 Limpieza de la bujía, ajuste de la distancia de los electrodos o sustitución de la bujía
- 7.6 Ajuste del carburador
- 7.7 Mantenimiento de la herramienta
- 7.8 Mantenimiento
- 7.9 Comprobación después de las tareas de cuidado y mantenimiento
- 8 Transporte y almacenamiento
- 9 Ayuda sobre averías
- 10 Reciclaje
- 11 Garantía del fabricante
- Manual de instruções original
- 1 Indicações sobre a documentação
- 2 Segurança
- 3 Descrição
- 4 Características técnicas
- 5 Preparação do local de trabalho
- 5.1 Combustível
- 5.2 Trabalhos de montagem e de afinação
- 5.3 Bloquear o movimento de rotação dos rolos de guia
- 5.4 Montar a ferramenta de corte a gasolina no carro-guia (acessório)
- 5.5 Montar a bomba da água (acessório)
- 5.6 Desmontar a bomba da água (acessório)
- 5.7 Ligar o motor
- 5.8 Verificações após arranque do motor
- 5.9 Desligar o motor
- 6 Trabalhar
- 7 Conservação e manutenção
- 7.1 Tabela de manutenção
- 7.2 Limpar ou substituir o filtro do ar
- 7.3 Substituir um cabo arrancador partido
- 7.4 Substituir o filtro de combustível
- 7.5 Limpar a vela de ignição, ajustar a folga dos eléctrodos ou substituir a vela de ignição
- 7.6 Afinar o carburador
- 7.7 Manutenção da ferramenta
- 7.8 Manutenção
- 7.9 Verificação após trabalhos de conservação e manutenção
- 8 Transporte e armazenamento
- 9 Ajuda em caso de avarias
- 10 Reciclagem
- 11 Garantia do fabricante
6 English 2271385
*2271385*
▶ Guide the product smoothly and do not apply lateral pressure to the cutting disc. Always bring the cutting
disc into contact with the workpiece at right angles. Don’t attempt to alter the line of cut by applying
lateral pressure or by bending the cutting disc while cutting is in progress.
▶ Abrasive cutting discs which are used for wet cutting must be used up the same day as long periods of
exposure to moisture have a negative effect on the strength of the disc.
▶ Never install a saw blade for cutting wood.
▶ Use only cutting discs that comply with the existing standards for cutting discs.
▶ Prior to installation and before use, check the cutting disc for damage. Do not install a damaged cutting
disc. Comply with the requirements stated by the manufacturer of the cutting disc.
3 Description
3.1 Product overview
3.1.1 Gasoline-powered cut-off saw 1
@
Guard
;
Water supply
=
Front grip
%
Water valve
&
Pull start
(
Fuel tank cap
)
Throttle trigger
+
Rear grip
§
Fuel-level sight glass
/
Guide rollers
:
Cutting disc
∙
Clamping screw
$
Clamping flange
£
Spark plug connector
|
Decompression valve
¡
Throttle safety grip
Q
Run/stop switch with half-throttle lock
W
Primer bulb
E
Water connection
R
Grip for guard adjustment
T
Disc direction-of-rotation indicator (arrow at
front of guard)
Z
Saw arm
U
Hole for locking pin for changing cutting
discs
I
Pump cover
O
Air filter cover