Operating Instruction DST WRC-CA (01)
Table Of Contents
- Original operating instructions
- Contents
- 1 Information about the documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Preparations at the workplace
- 5.1 Removing the battery
- 5.2 Charging the battery
- 5.3 Inserting the battery
- 5.4 Pairing the remote control unit and partner device
- 5.5 Setting the language, country and unit of measure
- 5.6 Setting the line fuse rating
- 5.7 Setting the cutting parameters
- 5.8 Saw blade diameter and blade guard
- 5.9 Activating cooling water control
- 5.10 Changing the password
- 5.11 Setting screen brightness
- 5.12 Setting the date and time
- 5.13 Reading messages
- 5.14 Reading the logbook
- 5.15 Technical information and next service
- 5.16 Resetting the settings
- 6 Manual operation
- 7 Assisted operation with Cut Assist
- 8 Care and maintenance of cordless tools
- 9 Transport and storage of cordless tools
- 10 Troubleshooting
- 11 Disposal
- 12 Manufacturer’s warranty
- 13 FCC statement (applicable in US) / IC statement (applicable in Canada)
18 English 2053458
*2053458*
9 Transport and storage of cordless tools
Transport
CAUTION
Accidental starting during transport !
▶ Always transport your products with the batteries removed!
▶ Remove the battery.
▶ Transport the tool and batteries individually packaged.
▶ Never transport batteries in bulk form (loose, unprotected).
▶ Check the tool and batteries for damage before use after long periods of transport.
Storage
CAUTION
Accidental damage caused by defective or leaking batteries !
▶ Always store your products with the batteries removed!
▶ Store the tool and batteries in a place that is as cool and dry as possible.
▶ Never store batteries in direct sunlight, on heating units or behind a window pane.
▶ Store the tool and batteries in a place where they cannot be accessed by children or unauthorized
persons.
▶ Check the tool and batteries for damage before use after long periods of storage.
10 Troubleshooting
If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by
yourself, please contact Hilti Service.
Trouble or fault Possible cause Action to be taken
The remote control unit re-
fuses to switch on or the
screen remains dark.
The battery is discharged ▶ Change the battery and charge
the empty battery.
▶ Work with the remote control
cable.
▶ Contact HILTI service.
Failure of the remote control
unit and/or screen to respond
to user inputs.
Software fault ▶ Switch off the electricity supply
to the remote control unit and
the partner device and restart.
▶ Contact HILTI service.
Cutting parameters cannot be
changed.
Password forgotten ▶ Contact HILTI service.
11 Disposal
Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The
materials must be correctly separated before they can be recycled. In many countries, your old tools,
machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative
for further information.
Battery disposal
Improper disposal of batteries can result in health hazards from leaking gases or fluids.
▶ DO NOT send batteries through the mail!
▶ Cover the terminals with a non-conductive material (such as electrical tape) to prevent short circuiting.
▶ Dispose of your battery out of the reach of children.
▶ Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public
health and safety resources for disposal instructions.
▶ Do not dispose of power tools, electronic equipment or batteries as household waste!
Printed: 09.03.2018 | Doc-Nr: PUB / 5200730 / 000 / 03