Specification

Hilti Adhesive Anchor
1.2 Material Specifications
4
Hilti, Inc. (USA) 1-800-879-8000 I www.us.hilti.com I en español 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I HIT-HY 70 Submittal Information 08/13
Material Properties for HIT-HY 70 — Cured Adhesive
Compressive Strength ASTMD695/DIN53454 7,252-10,153psi 50-70MPa
Modulusofelasticity(Compressiontest) ASTMD790/DIN53452 246,568psi 1,700MPa
Water Absorption ASTMD570/DIN53495 3-8% 3-8%
ElectricalResistance VDE/DIN0303T3 2.705-10
12
ohm/in. 1.065-10
12
ohm/cm
Material Specifications
Mechanical Properties
f
y
min. f
u
ksi(MPa) ksi(MPa)
StandardHAS-ErodmaterialmeetstherequirementsofISO898Class5.8 58 (400) 72.5 (500)
HighStrengthor“SuperHAS”rodmaterialmeetstherequirementsofASTMA193,GradeB7 105 (724) 125 (862)
StainlessHASrodmaterialmeetstherequirementsofASTMF593(AISI304/316)ConditionCW
3/8"to5/8"
65 (448) 100 (689)
StainlessHASrodmaterialmeetstherequirementsofASTMF593(AISI304/316)ConditionCW3/4" 45 (310) 85 (586)
CarbonSteelHIS-NInsertconfirmingtoDIN10277-3 54.4 (375) 66.7 (460)
StainlessSteelHIS-RNInsertconformingtoDIN10088-3 50.8 (350) 101.5 (700)
CarbonSteelHIT-ICInsertconformingtoDIN10277-3 54.4 (375) 66.7 (460)
HASSuperandHAS-EStandardNutMaterialmeetstherequirementsofSAEJ995Grade5
HASStainlessSteelNutmaterialmeetstherequirementsofASTMF594
HAS-ECarbonSteelandStainlessSteelWashersmeetdimensionalrequirementsofANSIB18.22.1TypeAPlain
HASStainlessSteelWashersmeettherequirementsofAISI304orAISI316conformingtoASTMA240
HASSuperandHAS-EStandardWashersmeettherequirementsofASTMF884,HV
AllHAS-EandHASSuperRodsandHAS-EStandard,HIS-Ninserts,nutsandwashersarezincplatedto
ASTMB633SC1
Note: Special Order steel rod material may vary from standard materials.
1.3 Technical Data
HIT-HY 70 Allowable Tension and Shear Values for Threaded Rods Based on Steel Strength
1, 2, 3
Anchor
Diameter
in.(mm)
Tension,lb(kN) Shear,lb(kN)
ASTM
A36
ASTM
A307
ASTM
A193B7
ISO898
Class5.8
ASTMF593
CW
(304/316)
ASTM
A36
ASTM
A307
ASTM
A193B7
ISO898
Class5.8
ASTMF593
CW
(304/316)
1/4
(6.4)
940
(4.2)
972
(4.3)
2025
(9.0)
1175
(5.2)
1620
(7.2)
485
(2.2)
500
(2.2)
1040
(4.6)
605
(2.7)
835
(3.7)
5/16
(7.9)
1470
(6.5)
1520
(6.8)
3160
(14.1)
1835
(8.2)
2530
(11.3)
756
(3.4)
780
(3.5)
1630
(7.3)
945
(4.2)
1300
(5.8)
3/8
(9.5)
2115
(9.4)
2185
(9.7)
4555
(20.3)
2640
(11.7)
3645
(16.2)
1090
(4.8)
1125
(5.0)
2345
(10.4)
1360
(6.1)
1875
(8.3)
1/2
(12.7)
3755
(16.7)
3885
(17.3)
8100
(36.0)
4700
(20.9)
6480
(28.8)
1935
(8.6)
2000
(8.9)
4170
(18.6)
2420
(10.8)
3335
(14.8)
5/8
(15.9)
5870
(26.1)
6075
(27.0)
12655
(56.3)
7340
(32.7)
10125
(45.0)
3025
(13.5)
3130
(13.9)
6520
(29.0)
3780
(16.8)
5215
(23.2)
3/4
(19.1)
8455
(37.6)
8750
(38.9)
18225
(81.1)
10570
(47.0)
14580
(64.9)
4355
(19.4)
4506
(20.0)
9388
(41.8)
5445
(24.2)
7510
(33.4)
1Allowableloadusedinthedesignmustbethelesserofbondvaluesandtabulatedsteelvalues.
2Theallowabletensionandshearvaluesforthreadedrodstoresistshorttermloads,suchaswindorseismic,mustbecalculatedinaccordancewiththeappropriateIBC
Sections.
3Allowablesteelloadsarebasedonallowabletensionandallowableshearstressesequalto0.33xF
u
and0.17xF
u
, respectively.