TE 2 TE 2-M TE 2-S English Printed: 04.10.
Printed: 04.10.
1 Information about the documentation 1.1 About this documentation • • • Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product. Observe the safety instructions and warnings in this documentation and on the product. Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons. 1.2 Explanation of signs used 1.2.
Rated speed under no load Revolutions per minute Protection class II (double-insulated) 1.4 Product information Hilti products are designed for professional use and may be operated, serviced and maintained only by trained, authorized personnel. This personnel must be informed of any particular hazards that may be encountered. The product and its ancillary equipment can present hazards if used incorrectly by untrained personnel or if used not in accordance with the intended use.
Personal safety ▶ Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. ▶ Use personal protective equipment. Always wear eye protection.
▶ ▶ ▶ ▶ ▶ Always lead the supply cord and extension cord away from the power tool to the rear while working. This helps to avoid tripping over the cord while working. Dust from materials, such as paint containing lead, some wood species, concrete / masonry / stone containing silica, and minerals as well as metal, may be harmful. Contact with or inhalation of the dust may cause allergic reactions and/or respiratory or other diseases to the operator or bystanders.
English Printed: 04.10.
6 English Printed: 04.10.
3 Description 3.1 Overview of the product English Printed: 04.10.
@ ; = % & ( Three-jaw chuck (TE 2-M) Dust shield Chuck Chuck locking ring (TE 2-M) Depth gauge Function selector switch ) + § / : ∙ Forward / reverse switch Grip Control switch Lockbutton Rating plate Side handle 3.2 Intended use The product described is an electrically powered rotary hammer. It is designed for drilling in concrete, masonry, drywall / gypsum board, plastic, wood, metal and for driving and removing screws.
5 Operation 5.1 Fitting the side handle CAUTION Risk of injury! The depth gauge, if fitted but not used, might hinder the operator. ▶ Remove the depth gauge from the tool. CAUTION Risk of injury! Loss of control over the rotary hammer drill. ▶ ▶ Check that the side handle is fitted correctly and tightened securely. Check that the clamping band is engaged in the groove in the tool. Fit the side handle. 5.2 Fitting / removing the chuck TE 2-M ▶ Fit / remove the chuck. 5.
Fit the accessory tool into the SDS chuck or, respectively, remove the accessory tool from the SDS chuck. ▶ 5.4 Fitting/removing the drill bit or other accessory: Quick-release chuck TE 2-M Fit the drill bit or other accessory in the quick-release chuck or, respectively, remove the drill bit or other accessory from the quick-release chuck. ▶ 5.5 Adjusting the depth gauge Note Always pay attention to the maximum length of the depth gauge. 10 English Printed: 04.10.
▶ Adjust the depth gauge. 5.6 Drilling with hammering action (hammer drilling) ▶ Set the function selector switch to the “Drilling with hammering action” (hammer drilling) position . 5.7 Light hammering action TE 2-S ▶ Set the function selector switch to the “Light hammering action” position. English Printed: 04.10.
5.8 Drilling TE 2 TE 2-S Set the function selector switch to the “Drilling” ▶ 5.9 Drilling in first gear position. or drilling in second gear TE 2-M Set the function selector switch to the “Drilling in first gear” or “Drilling in second gear” position. ▶ 5.10 Forward / reverse Risk of damage Actuation while the tool is running may result in damage to the gearing. ▶ 12 Do not operate the forward / reverse switch while the motor is running. English Printed: 04.10.
▶ Set the forward / reverse selector switch to forward or reverse rotation. 6 Care and maintenance WARNING Danger of electric shock! Carrying out care and maintenance while the supply cord is connected to the power outlet presents a risk of serious injuries including burns. ▶ Always unplug the supply cord before carrying out all care and maintenance tasks. Care • Carefully remove stubborn dirt from the tool. • Clean the air vents carefully with a dry brush.
6.1 Replacing the dust shield Replace the dust shield. ▶ 7 Transport and storage • • • Do not transport electric tools with accessory tools fitted. Always unplug the supply cord before storing an electric tool or appliance. Store tools and appliances in a dry place where they cannot be accessed by children or unauthorized persons. Check electric tools or appliances for damage after long periods of transport or storage.
Trouble or fault The drill bit makes no progress. Possible cause The power tool has been set to reverse rotation. Action to be taken ▶ Set the power tool to forward rotation. 9 Disposal Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling.
16 English Printed: 04.10.
Printed: 04.10.
Hilti = registered trademark of Hilti Corp., Schaan Printed: 04.10.
