DS-K5671B Series Face Recognition Terminal User Manual
DS-K5671B Series Face Recognition Terminal User Manual Legal Information ©2022 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K5671B Series Face Recognition Terminal User Manual DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed.
DS-K5671B Series Face Recognition Terminal User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
DS-K5671B Series Face Recognition Terminal User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K5671B Series Face Recognition Terminal User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
DS-K5671B Series Face Recognition Terminal User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K5671B Series Face Recognition Terminal User Manual Cautions: ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
DS-K5671B Series Face Recognition Terminal User Manual If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
DS-K5671B Series Face Recognition Terminal User Manual Available Models Product Name Face Recognition Terminal Model DS-K5671B-ZV DS-K5671B-ZH DS-K5671B-ZU Use only power supplies listed in the user instructions: Model Manufacturer Standard C2000IC12.0-24P-DE MOSO Power Supply Technology Co., Ltd. CEE C2000IC12.0-24P-GB MOSO Power Supply Technology Co., Ltd. BS KPL-040F-VI Channel Well Technology Co Ltd.
DS-K5671B Series Face Recognition Terminal User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Overview ................................................................................................................................ 1 1.2 Features .................................................................................................................................
DS-K5671B Series Face Recognition Terminal User Manual 6.6 Privacy Settings .................................................................................................................... 39 6.7 Set Administrator ................................................................................................................. 40 Chapter 7 Basic Operation ........................................................................................................ 43 7.1 Login .................................
DS-K5671B Series Face Recognition Terminal User Manual 7.6 Basic Settings ....................................................................................................................... 67 7.7 Set Biometric Parameters .................................................................................................... 69 7.8 Set Access Control Parameters ............................................................................................ 72 7.9 Time and Attendance Status Settings ............
DS-K5671B Series Face Recognition Terminal User Manual 8.6.6 Upgrade and Maintenance ......................................................................................... 91 8.6.7 Log Query .................................................................................................................... 93 8.6.8 Security Mode Settings ............................................................................................... 93 8.6.9 Certificate Management .........................................
DS-K5671B Series Face Recognition Terminal User Manual 9.4.1 Add Organization ...................................................................................................... 136 9.4.2 Configure Basic Information ..................................................................................... 137 9.4.3 Issue a Card by Local Mode ....................................................................................... 138 9.4.4 Upload a Face Photo from Local PC ......................................
DS-K5671B Series Face Recognition Terminal User Manual 9.7.3 Configure Multi-Factor Authentication ..................................................................... 164 9.7.4 Configure Card Reader Authentication Mode and Schedule .................................... 166 9.7.5 Configure First Person In ........................................................................................... 168 9.7.6 Configure Anti-Passback ...............................................................................
DS-K5671B Series Face Recognition Terminal User Manual 9.12.2 Set Picture Storage .................................................................................................. 212 9.12.3 Set Alarm Sound ..................................................................................................... 213 9.12.4 Set Access Control and Video Intercom Parameters ............................................... 213 9.12.5 Set File Saving Path ..............................................................
DS-K5671B Series Face Recognition Terminal User Manual Chapter 1 Overview 1.1 Overview Face recognition terminal is a kind of access control device for face recognition, which is mainly applied in security access control systems, such as logistic centers, airports, university campuses, alarm centrals, dwellings, etc. 1.
DS-K5671B Series Face Recognition Terminal User Manual Chapter 2 Appearance Refer to the following contents for detailed information of the face recognition terminal: Figure 2-1 Face Recognition Terminal Diagram Table 2-1 Description of Face Recognition Terminal No. Name Description 1 White Light Supplement light for camera. 2 IR Light Supplement light for camera. 3 Camera White light camera for recording or capturing white light videos or pictures. 4 Display Screen 7-inch LCD touch screen.
DS-K5671B Series Face Recognition Terminal User Manual No. Name Description 10 Debugging Port The debug terminal is used for debugging only. 11 Network Interface Connect to Ethernet.
DS-K5671B Series Face Recognition Terminal User Manual Chapter 3 Installation 3.1 Installation Environment ● ● ● ● ● ● ● Avoid backlight, direct sunlight, and indirect sunlight. For better recognition, there should be light source in or near the installation environment. The minimum bearing weight of the wall or other places should be 3 times heavier than the device weight.
DS-K5671B Series Face Recognition Terminal User Manual Figure 3-1 Drill Holes on Turnstile 3. Solder the other four holes, polish the surface, and implement wire drawing. 4. Solder circular tubes on the turnstile’s inner surface to avoid water from entering.
DS-K5671B Series Face Recognition Terminal User Manual Figure 3-2 Solder Tubes 3.2.2 Mount Bracket I Steps 1. Install the base on the turnstile. 1) Align the hole on the turnstile and place the base on the turnstile. 2) Rotate the base to the acquired place and make sure the device will face a correct direction. 3) Secure the base with 2 screws.
DS-K5671B Series Face Recognition Terminal User Manual Figure 3-3 Install Base ● ● Note The arrow indication on the base and the turnstile should be approximately vertical. Refer to the scales and scale arrow on the base to confirm the screws position. The screws' position indicated scale is the rotate angle of the device.
DS-K5671B Series Face Recognition Terminal User Manual Figure 3-4 Screw Position 2. Route the cables through the cable hole on the turnstile. 3. Install the bracket on the base. 1) Place the device with bracket on the base and make sure the arrow on the base is aligned with the arrow shaped slot on the bracket. The holes on the bracket is aligned with those on the bracket. 2) Use 6 screws to secure the base and the lower cover.
DS-K5671B Series Face Recognition Terminal User Manual Figure 3-5 Secure Lower Cover and Turnstile 4. Secure the upper cover. 1) Align the arrow indication on the base with that inside the upper cover. 2) Place the upper cover in the lower cover. 3) Rotate the upper cover to the right until the buckle is fastened.
DS-K5671B Series Face Recognition Terminal User Manual Figure 3-6 Secure Upper Cover 5. After installation, for the proper use of the device (outdoor use), stick the protection film (parts of models supplied) on the screen. 3.2.3 Mount Bracket II Steps 1. Rotate to open the lower cover.
DS-K5671B Series Face Recognition Terminal User Manual Figure 3-7 Remove Lower Cover 2. Route the cables through the cable hole on the turnstile. 3. Align the holes on the base with those on the turnstile and place the device with bracket on the turnstile. 4. Use 4 screws to secure the bracket and the turnstile.
DS-K5671B Series Face Recognition Terminal User Manual Figure 3-8 Secure Bracket and Turnstile 5. Install the lower cover back on the base and rotate to secure. 6. Adjust the device elevation. 1) Loosen the screws inside. 2) Adjust the device elevation. 3) After adjustment, secure the screws and install the upper cover. Note The default elevation angle is 15°. The adjustable elevation angle is from 0° to 15°.
DS-K5671B Series Face Recognition Terminal User Manual Figure 3-10 Adjust Elevation 7. After installation, for the proper use of the device (outdoor use), stick the protection film (parts of models supplied) on the screen. 3.2.4 Mount Bracket III Steps 1. Route the cables through the cable hole on the turnstile. 2. Align the holes on the bracket and those on the turnstile and place the bracket on the turnstile.
DS-K5671B Series Face Recognition Terminal User Manual Figure 3-11 Install Bracket on Turnstile 3. Optional: By default, a decoration sheet is on the bracket. You can replace it by the arch shaped decoration (supplied) when the default one cannot cover all holes on the turnstile. 1) Remove the 2 screws on the lower side of the bracket and remove the decoration sheet.
DS-K5671B Series Face Recognition Terminal User Manual Figure 3-12 Remove Screws 2) Align the screw holes on the arch shaped decoration with the those on the bracket and secure them with 2 screws. Figure 3-13 Arch Shaped Decoration 4. Rotate to adjust the bracket's angle and secure the bracket on the turnstile with 2 screws.
DS-K5671B Series Face Recognition Terminal User Manual Figure 3-14 Secure Bracket 5. Align the device with the bracket and slide the device in the bracket. Make sure the two sheets of the mounting plate are in the slots.
DS-K5671B Series Face Recognition Terminal User Manual Figure 3-15 Install Device 6. Secure the device and the bracket with a screw.
DS-K5671B Series Face Recognition Terminal User Manual Figure 3-16 Secure Device 7. After installation, for the proper use of the device (outdoor use), stick the protection film (parts of models supplied) on the screen.
DS-K5671B Series Face Recognition Terminal User Manual Chapter 4 Wiring You can connect the RS-485 terminal with the RS-485 card reader, connect the NC and COM terminal with the door lock, connect the SENSOR terminal with the door contact, the BTN/GND terminal with the exit button, connect the alarm output and input terminal with the alarm output/ input devices, and connect the Wiegand terminal with the Wiegand card reader or the access controller.
DS-K5671B Series Face Recognition Terminal User Manual Figure 4-1 Terminal Diagram The descriptions of the terminals are as follows: 20
DS-K5671B Series Face Recognition Terminal User Manual Table 4-1 Terminal Descriptions Group Group A No.
DS-K5671B Series Face Recognition Terminal User Manual Group No. Function Color Name Description D4 Yellow/Green SENSOR Door Contact D5 Yellow/Gray BTN Exit Door Wiring 4.2 Wire Normal Device You can connect the terminal with normal peripherals. The wiring diagram without secure door control unit is as follows. Figure 4-2 Device Wiring ● ● ● ● ● Note You should set the face recognition terminal's Wiegand direction to "Input" to connect to a Wiegand card reader.
DS-K5671B Series Face Recognition Terminal User Manual 4.3 Wire Secure Door Control Unit You can connect the terminal with the secure door control unit. The wiring diagram is as follows. Figure 4-3 Secure Door Control Unit Wiring ● ● ● ● Note The secure door control unit should connect to an external power supply separately. The suggested external power supply is 12V, 0.5A. For scenarios with high safety requirement, use the secure door control unit wiring first.
DS-K5671B Series Face Recognition Terminal User Manual Chapter 5 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: ● The default IP address: 192.0.0.64 ● The default port No.: 8000 ● The default user name: admin 5.
DS-K5671B Series Face Recognition Terminal User Manual Figure 5-1 Activation Page Caution The password strength of the device can be automatically checked.
DS-K5671B Series Face Recognition Terminal User Manual characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. Note Characters containing admin and nimda are not supported to be set as activation password.
DS-K5671B Series Face Recognition Terminal User Manual Before You Start ● Get the SADP software from the supplied disk or the official website http:// www.hikvision.com/en/ , and install the SADP according to the prompts. ● The device and the PC that runs the SADP tool should be within the same subnet. The following steps show how to activate a device and modify its IP address. For batch activation and IP addresses modification, refer to User Manual of SADP for details. Steps 1.
DS-K5671B Series Face Recognition Terminal User Manual 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP. 3) Input the admin password and click Modify to activate your IP address modification. 5.4 Activate Device via Client Software For some devices, you are required to create the password to activate them before they can be added to the software and work properly.
DS-K5671B Series Face Recognition Terminal User Manual Chapter 6 Quick Operation 6.1 Select Language You can select a language for the device system. After the device activation, you can select a language for the device system.
DS-K5671B Series Face Recognition Terminal User Manual Figure 6-1 Select System Language By default, the system language is English.
DS-K5671B Series Face Recognition Terminal User Manual 6.2 Set Password Change Type After activating the device, you can set the password change type as reserved email address or security questions. Once you forgot the device password, you can change the password via the selected change type. Change Password via Email Address If you need to change password via reserved email, you can enter an email address, and tap Next.
DS-K5671B Series Face Recognition Terminal User Manual Figure 6-2 Password Change Page Change via Security Questions If you need to change password via security questions, you can tap Change to Security Questions on the right corner. Select the security questions and enter the answers. Click Next.
DS-K5671B Series Face Recognition Terminal User Manual Note You can only select one type to change password. If you need, you can enter the web page to set both of the changing types. 6.3 Set Application Mode After activating the device, you should select an application mode for better device application. Steps 1. On the Welcome page, select Indoor or Others from the drop-down list.
DS-K5671B Series Face Recognition Terminal User Manual Figure 6-3 Welcome Page 2. Tap OK to save. ● ● Note You can also change the settings in System Settings. If you install the device indoors near the window or the face recognition function is not working well, select Others.
DS-K5671B Series Face Recognition Terminal User Manual ● ● If you do not configure the application mode and tap Next, the system will select Indoor by default. If you activate the device via other tools remotely, the system will select Indoor as the application mode by default. 6.4 Set Network Parameters After activation and select application mode, you can set the network for the device Steps 1. When you enter the Select Network page, tap Wired Network or Wi-Fi for your actual needs.
DS-K5671B Series Face Recognition Terminal User Manual Figure 6-4 Select Network Note Disconnect the wired network before connecting a Wi-Fi. 2. Tap Next. Wired Network Note Make sure the device has connected to a network.
DS-K5671B Series Face Recognition Terminal User Manual If enable DHCP, the system will assign the IP address and other parameters automatically. If disable DHCP, you should set the IP address, the subnet mask, and the gateway. Note IP address of 192.168.1.64, and 192.168.1.7 are not suggested to use. Wi-Fi Select a Wi-Fi and enter the Wi-Fi's password to get connected. Or tap Add Wi-Fi and enter the Wi-Fi's name and the password to get connected. 3. Optional: Tap Skip to skip network settings. 6.
DS-K5671B Series Face Recognition Terminal User Manual Figure 6-5 Access to Hik-Connect 2. Tap Next. 3. Optional: Tap Skip to skip the step. 4. Optional: Tap Previous to go to the previous page. Note If you tap Previous to return to the Wi-Fi configuration page, you need to tap the connected WiFi or connect another Wi-Fi to enter the platform page again.
DS-K5671B Series Face Recognition Terminal User Manual 6.6 Privacy Settings After activation, selecting application mode, and selecting network, you should set the privacy parameters, including the picture uploading and storage. Select parameters according to your actual needs.
DS-K5671B Series Face Recognition Terminal User Manual Upload Captured Pic. When Auth. (Upload Captured Picture When Authenticating) Upload the pictures captured when authenticating to the platform automatically. Save Captured Pic. When Auth. (Save Captured Picture When Authenticating) If you enable this function, you can save the picture when Authenticating to the device. Save Registered Pic. (Save Registered Picture) The registered face picture will be saved to the system if you enable the function.
DS-K5671B Series Face Recognition Terminal User Manual Figure 6-7 Add Administrator Page 3. Select a credential to add. Note Up to one credential should be added. - : Face forward at the camera. Make sure the face is in the face recognition area. Click capture and click to confirm.
DS-K5671B Series Face Recognition Terminal User Manual : Enter the card No. or present card on the card presenting area. Click OK. Click OK. 4. You will enter the authentication page. Status Icon Description / Device is armed/not armed. / Hik-Connect is enabled/disabled. / / The device wired network is connected/not connected/connecting failed. / / The device' Wi-Fi is enabled and connected/not connected/enabled but not connected.
DS-K5671B Series Face Recognition Terminal User Manual Chapter 7 Basic Operation 7.1 Login Login the device to set the device basic parameters. 7.1.1 Login by Administrator If you have added an administrator for the device, only the administrator can login the device for device operation. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter the admin login page.
DS-K5671B Series Face Recognition Terminal User Manual Figure 7-1 Admin Login 2. Authenticate the administrator's face or card to enter the home page.
DS-K5671B Series Face Recognition Terminal User Manual Figure 7-2 Home Page Note The device will be locked for 30 minutes after 5 failed attempts. 3. Optional: Tap and you can enter the device activation password for login. 4. Optional: Tap and you can exit the admin login page.
DS-K5671B Series Face Recognition Terminal User Manual 7.1.2 Login by Activation Password You should login the system before other device operations. If you do not configure an administrator, you should follow the instructions below to login. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter password entering page. 2. Tap the Password field and enter the device activation password. 3. Tap OK to enter the home page.
DS-K5671B Series Face Recognition Terminal User Manual Figure 7-3 Home Page 7.1.3 Forgot Password If you forget the password during authentication, you can change the password.
DS-K5671B Series Face Recognition Terminal User Manual Steps 1. Hold the initial page for 3 s and slide to the left/right by following the gesture and log in the page. 2. Optional: If you have set an administrator, tap in the pop-up admin authentication page. Figure 7-4 Password Authentication Page 3. Tap Forgot Password. 4. Select a password change type from the list.
DS-K5671B Series Face Recognition Terminal User Manual Note If you have only set 1 password change type, you will go to the corresponded password change page for further settings. 5. Answer the security questions or change the password according to email address. - Security Questions: Answer the security questions that configured when activation. - Email Address Note Make sure the device has added to the Hik-Connect account. a. Download Hik-Connect app. b. Go to More → Reset Device Password . c.
DS-K5671B Series Face Recognition Terminal User Manual Figure 7-5 Wired Network Settings 3. Set IPv4/IPv6 IP Address, Subnet Mask, and Gateway. - Enable DHCP, and the system will assign IP address, subnet mask, and gateway automatically. - Disable DHCP, and you should set the IP address, subnet mask, and gateway manually. Note The device's IP address and the computer IP address should be in the same IP segment.
DS-K5671B Series Face Recognition Terminal User Manual 4. Set the DNS parameters. You can enable Auto Obtain DNS, set the preferred DNS server and the alternate DNS server. 7.2.2 Set Wi-Fi Parameters You can enable the Wi-Fi function and set the Wi-Fi related parameters. Steps Note The function should be supported by the device. 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap.
DS-K5671B Series Face Recognition Terminal User Manual Figure 7-6 Wi-Fi Settings 3. Enable the Wi-Fi function. 4. Configure the Wi-Fi parameters. - Select a Wi-Fi from the list, and enter the Wi-Fi's password. Tap OK. - If the target Wi-Fi is not in the list,tap Add Wi-Fi. Enter the Wi-Fi's name and password. And tap OK. Note Only digits, letters, and special characters are allowed in the password. 5. Set the Wi-Fi's parameters. - By default, DHCP is enable.
DS-K5671B Series Face Recognition Terminal User Manual 6. Tap OK to save the settings and go back to the Wi-Fi tab. to save the network parameters. 7. Tap 7.2.3 Set RS-485 Parameters The face recognition terminal can connect external access controller, secure door control unit or card reader via the RS-485 terminal. Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap RS-485 to enter the RS-485 tab.
DS-K5671B Series Face Recognition Terminal User Manual Figure 7-7 Set RS-485 Parameters 3. Enable RS-485 Settings. 4. Select an peripheral type according to your actual needs.
DS-K5671B Series Face Recognition Terminal User Manual Note If you select Access Controller: If connect the device to a terminal via the RS-485 interface, set the RS-485 address as 2. If you connect the device to a controller, set the RS-485 address according to the door No. 5. Tap the back icon at the upper left corner and you should reboot the device if you change the parameters. 7.2.4 Set Wiegand Parameters You can set the Wiegand transmission direction. Steps 1. Tap Comm.
DS-K5671B Series Face Recognition Terminal User Manual 3. Enable the Wiegand function. 4. Select a transmission direction. ● Output: A face recognition terminal can connect an external access controller. And the two devices will transmit the card No. via Wiegand 26 or Wiegand 34. ● Input: A face recognition terminal can connect a Wiegand card reader. to save the network parameters. 5. Tap Note If you change the external device, and after you save the device parameters, the device will reboot automatically.
DS-K5671B Series Face Recognition Terminal User Manual Figure 7-9 ISUP Settings 2. Enable the ISUP function and set the ISUP server parameters. ISUP Version Set the ISUP version according to your actual needs. Central Group Enable central group and the data will be uploaded to the center group. Main Channel Support N1 or None. ISUP Enable ISUP function and the data will be uploaded via ISUP protocol. Address Type Select an address type according to your actual needs.
DS-K5671B Series Face Recognition Terminal User Manual Set the ISUP server's IP address. Port No. Set the ISUP server's port No. Note Port No. Range: 0 to 65535. Device ID Set device serial no. ISUP Key If you choose V5.0, you should create an account and ISUP key. If you choose other version, you should create an ISUP account only. ● ● Note Remember the ISUP account and ISUP key. You should enter the account name or the key when the device should communicate with other platforms via ISUP protocol.
DS-K5671B Series Face Recognition Terminal User Manual 7.3.1 Add Administrator The administrator can log in the device backend and configure the device parameters. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture and enter the device backend. 2. Tap User → + to enter the Add User page.
DS-K5671B Series Face Recognition Terminal User Manual 3. Edit the employee ID. Note ● The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers. ● The employee ID should not be duplicated. 4. Tap the Name field and input the user name on the soft keyboard. Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● Up to 32 characters are allowed in the user name. 5.
DS-K5671B Series Face Recognition Terminal User Manual Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● The suggested user name should be within 32 characters. 5. Tap the Face Picture field to enter the face picture adding page.
DS-K5671B Series Face Recognition Terminal User Manual 6. Look at the camera. ● ● ● Note Make sure your face picture is in the face picture outline when adding the face picture. Make sure the captured face picture is in good quality and is accurate. For details about the instructions of adding face pictures, see Tips When Collecting/ Comparing Face Picture . After completely adding the face picture, a captured face picture will be displayed at the upper right corner of the page. 7.
DS-K5671B Series Face Recognition Terminal User Manual Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● The suggested user name should be within 32 characters. 6. Tap the Card field and tap +. 7. Configure the card No. - Enter the card No. manually. - Present the card over the card presenting area to get the card No. Note ● The card No. cannot be empty. ● Up to 20 characters are allowed in the card No. ● The card No. cannot be duplicated. 8.
DS-K5671B Series Face Recognition Terminal User Manual Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● The suggested user name should be within 32 characters. 5. Tap the PIN code to view the PIN code. Note The PIN code cannot be edited. It can only be applied by the platform. 6. Set the user role. Administrator The user is the administrator.
DS-K5671B Series Face Recognition Terminal User Manual Search User On the User Management page, Tap the search area to enter the Search User page. Tap Card on the left of the page and select a search type from the drop-down list. Enter the employee ID, card No., or the user name for search. Tap to search. Edit User On the User Management page, select a user from the user list to enter the Edit User page. Follow the steps in User Management to edit the user parameters. Tap to save the settings.
DS-K5671B Series Face Recognition Terminal User Manual ● ● ● ● The imported pictures should be saved in the folder (named enroll_pic) of the root directory and the picture's name should be follow the rule below: Card No._Name_Department_Employee ID_Gender.jpg If the folder enroll_pic cannot save all imported pictures, you can create another folders, named enroll_pic1, enroll_pic2, enroll_pic3, enroll_pic4, under the root directory. The employee ID should be less than 32 characters.
DS-K5671B Series Face Recognition Terminal User Manual Face forward at the camera and start authentication via face. Card Present the card on the card presenting area and start authentication via card. Note The card can be normal IC card, or encrypted card. PWD Enter the password to authenticate via password. If authentication completed, a prompt "Authenticated" will pop up. 7.5.2 Authenticate via Multiple Credential Before You Start Set the user authentication type before authentication.
DS-K5671B Series Face Recognition Terminal User Manual Figure 7-11 Basic Settings Page Voice Settings You can enable/disable the voice prompt function and adjust the voice volume. Note You can set the voice volume between 0 and 10.
DS-K5671B Series Face Recognition Terminal User Manual Set the time zone, the device time and the DST. Sleeping (s) Set the device sleeping waiting time (minute). When you are on the initial page and if you set the sleeping time to 30 min, the device will sleep after 30 min without any operation. Note If you set the sleeping time to 0, the device will not enter sleeping mode. Select Language Select the language according to actual needs.
DS-K5671B Series Face Recognition Terminal User Manual Table 7-1 Face Picture Parameters Parameter Description Application Mode Select either others or indoor according to actual environment. Face Liveness Level After enabling face anti-spoofing function, you can set the matching security level when performing live face authentication. Face Recognition Distance Set the valid distance between the user and the camera when authenticating.
DS-K5671B Series Face Recognition Terminal User Manual Parameter Description Set the matching threshold when authenticating via ECO mode 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate Face with Mask & Face(1:1 ECO) Set the matching value when authenticating with face mask via ECO mode 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate.
DS-K5671B Series Face Recognition Terminal User Manual 7.8 Set Access Control Parameters You can set the access control permissions, including the functions of authentication mode, enable M1 card, door contact, open duration (s) and authentication interval (s). On the Home page, tap ACS (Access Control Settings) to enter the Access Control Settings page. Edit the access control parameters on this page.
DS-K5671B Series Face Recognition Terminal User Manual 7.9 Time and Attendance Status Settings You can set the attendance mode as check in, check out, break out, break in, overtime in, and overtime out according to your actual situation. Note The function should be used cooperatively with time and attendance function on the client software. 7.9.1 Disable Attendance Mode via Device Disable the attendance mode and the system will not display the attendance status on the initial page.
DS-K5671B Series Face Recognition Terminal User Manual Steps 1. Tap T&A Status to enter the T&A Status page. 2. Set the Attendance Mode as Manual. Figure 7-13 Manual Attendance Mode 3. Enable the Attendance Status Required. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. The name will be displayed on the T & A Status page and the authentication result page.
DS-K5671B Series Face Recognition Terminal User Manual 7.9.3 Set Auto Attendance via Device Set the attendance mode as auto, and you can set the attendance status and its available schedule. The system will automatically change the attendance status according to the configured schedule. Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Tap T&A Status to enter the T&A Status page. 2. Set the Attendance Mode as Auto.
DS-K5671B Series Face Recognition Terminal User Manual 4) Tap Confirm. 5) Repeat step 1 to 4 according to your actual needs. Note The attendance status will be valid within the configured schedule. Result When you authenticate on the initial page, the authentication will be marked as the configured attendance status according to the configured schedule.
DS-K5671B Series Face Recognition Terminal User Manual Figure 7-15 Manual and Auto Mode 3. Enable the Attendance Status function. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. The name will be displayed on the T & A Status page and the authentication result page. 6. Set the status' schedule. 1) Tap Attendance Schedule. 2) Select Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, or Sunday.
DS-K5671B Series Face Recognition Terminal User Manual Example If set the Break Out as Monday 11:00, and Break In as Monday 12:00, the valid user's authentication from Monday 11:00 to 12:00 will be marked as break. 7.10 System Maintenance You can view the system information and the capacity. You can also upgrade the device, restore to factory settings, restore to default settings, and reboot the device.
DS-K5671B Series Face Recognition Terminal User Manual You can view the device model, serial No., versions, address, production data, QR code, and open source code license. Note The page may vary according to different device models. Refers to the actual page for details. Capacity You can view the number of, user, face picture, card, event and fingerprint. Note Parts of the device models support displaying the fingerprint number. Refers to the actual page for details.
DS-K5671B Series Face Recognition Terminal User Manual Figure 7-17 Preference Settings Shortcut Key Choose the shortcut key that displayed on the authentication page, including the call function, call type, and the password entering function. Note You can select call type from Call Room, Call Center, Call Specified Room No. and Call APP.
DS-K5671B Series Face Recognition Terminal User Manual Call Room When you tap the call button on the authentication page, you should dial a room No. to call. Call Center When you tap the call button on the authentication page, you can call the center directly. Call Specified Room No. You should set a room No. When you tap the call button on the authentication page, you can call the configured room directly without dialing.
DS-K5671B Series Face Recognition Terminal User Manual 7.12.1 Call Client Software from Device Steps 1. Get the client software from the supplied disk or the official website, and install the software according to the prompts. 2. Run the client software and the control panel of the software pops up. 3. Click Device Management to enter the Device Management interface. 4. Add the device to the client software. Note For details about adding device, see Add Device. 5. Call the client software.
DS-K5671B Series Face Recognition Terminal User Manual Note The device will call the main station in priority. 7.12.3 Call Device from Client Software Steps 1. Get the client software from the supplied disk or the official website, and install the software according to the prompts. 2. Run the client software and the control panel of the software pops up. 3. Click Device Management to enter the Device Management page. 4. Add the device to the client software.
DS-K5671B Series Face Recognition Terminal User Manual 7.12.5 Call Mobile Client from Device Steps 1. Get the mobile mobile client from the supplied disk or the official website, and install the software according to the prompts. 2. Run the mobile client and add the device to the mobile client. Note For details, see the user manual of the mobile client. 3. Enter Basic Settings → Shortcut Key and enable Call APP. 4. Go back to the initial page and call the mobile client. 1) Tap on the device initial page.
DS-K5671B Series Face Recognition Terminal User Manual Chapter 8 Operation via Web Browser 8.1 Login You can login via the web browser or the remote configuration of the client software. Note Make sure the device is activated. Login via Web Browser Enter the device IP address in the address bar of the web browser and press Enter to enter the login page. Enter the device user name and the password. Click Login. Login via Remote Configuration of Client Software Download and open the client software.
DS-K5671B Series Face Recognition Terminal User Manual Figure 8-1 Live View Page Function Descriptions: Select the image size when starting live view. Set the volume when starting live view. Note If you adjust the volume when starting two-way audio, you may hear a repeated sounds. You can capture image when starting live view. Reserved function. You can zoom in the live view image. Unlock the linked door. Start or stop live view. Start or stop video recording.
DS-K5671B Series Face Recognition Terminal User Manual Select the window division type when starting live view. Full screen view. 8.4 Person Management Click and add the person's information, including the basic information, authentication mode, card, and fingerprint. And you can also edit user information, view user picture and search user information in the user list. Add Basic Information Click User → Add to enter the Add Person page.
DS-K5671B Series Face Recognition Terminal User Manual Click Add Card, enter the Card No. and select the Property, and click OK to add the card. Click OK to save the settings. Add Fingerprint Note Only devices supporting the fingerprint function can add the fingerprint. Click User → Add to enter the Add Person page. Click Add Fingerprint, and press your finger on the fingerprint module of the device to add your fingerprint. Click Complete to save the settings.
DS-K5671B Series Face Recognition Terminal User Manual Figure 8-2 Search Event Enter the search conditions, including the event type, the employee ID, the name, the card No., the start time, and the end time, and click Search. The results will be displayed on the right panel. 8.6 Configuration 8.6.1 Set Local Parameters Set the live view parameters, record file size and saving path, and captured pictures and clip saving path. Set Live View Parameters Click Configuration → Local to enter the Local page.
DS-K5671B Series Face Recognition Terminal User Manual Set Captured Pictures and Clips Saving Path Click Configuration → Local to enter the Local page. Select a saving path from your local computer and click Save. You can also click Open to open the file folder to view details. 8.6.2 View Device Information View the device name, language, model, serial No.
DS-K5671B Series Face Recognition Terminal User Manual NTP You should set the alarm receiver type, NTP server's IP address, port No., and interval. Manual By default, the device time should be synchronized manually. You can set the device time manually or check Sync. with Computer Time to synchronize the device time with the computer's time. 8.6.4 Set DST Steps 1. Click Configuration → System → System Settings → DST . Figure 8-4 DST Page 2. Check Enable DST. 3.
DS-K5671B Series Face Recognition Terminal User Manual Figure 8-5 Upgrade and Maintenance Page Click Reboot to start reboot the device. Restore Parameters Click Configuration → System → Maintenance → Upgrade & Maintenance . Restore All All parameters will be restored to the factory settings. You should activate the device before usage. Default The device will restore to the default settings, except for the device IP address and the user information.
DS-K5671B Series Face Recognition Terminal User Manual Import Click and select the file to import. Click Import to start import configuration file. Upgrade Click Configuration → System → Maintenance → Upgrade & Maintenance . Select an upgrade type from the drop-down list. Click and select the upgrade file from your local PC. Click Upgrade to start upgrading.
DS-K5671B Series Face Recognition Terminal User Manual In order to increase the network security level when visiting websites, you can enable HTTP to acquire a more secure and encrypted network communication environment. The communication should authenticated by identity and encryption password after enabling HTTP, which is save. 8.6.9 Certificate Management It helps to manage the server/client certificates and CA certificate. Note The function is only supported by certain device models.
DS-K5671B Series Face Recognition Terminal User Manual Install CA Certificate Before You Start Prepare a CA certificate in advance. Steps 1. Go to Configuration → System → Security → Certificate Management . 2. Create an ID in the Inport CA Certificate area. Note The input certificate ID cannot be the same as the existing ones. 3. Upload a certificate file from the local. 4. Click Install. 8.6.10 Change Administrator's Password Steps 1. Click Configuration → User Management . 2. Click . 3.
DS-K5671B Series Face Recognition Terminal User Manual 3. Enter the device password and click OK to confirm changing. 8.6.12 View Device Arming/Disarming Information View device arming type and arming IP address. Go to Configuration → User Management → Arming/Disarming Information . You can view the device arming/disarming information. Click Refresh to refresh the page. 8.6.13 Network Settings Set TCP/IP, port, Wi-Fi, report strategy, platform access and HTTP listening.
DS-K5671B Series Face Recognition Terminal User Manual Figure 8-6 TCP/IP Settings Page Set the parameters and click Save to save the settings. Network Card Select network card according to your actual needs. DHCP If uncheck the function, you should set the IPv4 address, IPv4 subnet mask, IPv4 default gateway, IPv6 mode, IPv6 address, IPv6 subnet prefix length, IPv6 default gateway, Mac address, and MTU.
DS-K5671B Series Face Recognition Terminal User Manual DNS Server Set the preferred DNS server and the Alternate DNS server according to your actual need. Set Port Parameters Set the HTTP, RTSP, HTTPS and Server port parmaeters. Click Configuration → Network → Basic Settings → Port . HTTP It refers to the port through which the browser accesses the device. For example, when the HTTP Port is modified to 81, you need to enter http://192.0.0.65:81 in the browser for login.
DS-K5671B Series Face Recognition Terminal User Manual Figure 8-7 Wi-Fi Settings Page 2. Check Wi-Fi. 3. Select a Wi-Fi - Click of a Wi-Fi in the list and enter the Wi-Fi password. - Click Add, and enter the SSID, working mode, and encryption type. Click Connect. When the Wi-Fi is connected, click OK. 4. Optional: Set the WLAN parameters. 1) Click Network Settings. 2) Set the IP address, subnet mask, and default gateway.
DS-K5671B Series Face Recognition Terminal User Manual Note N1 refers to wired network. Set ISUP Parameters Set the ISUP parameters for accessing device via ISUP protocol. Steps Note The function should be supported by the device. 1. Click Configuration → Network → Advanced Settings → Platform . 2. Select ISUP from the platform access mode drop-down list. 3. Check Enable. 4. Set the ISUP version, and view the alarm receiver type, server address, port, device ID, register status. Note If you select 5.
DS-K5671B Series Face Recognition Terminal User Manual 6. Click Save to enable the settings. Configure HTTP Listening The device can send alarm information to the event alarm IP address or domain name via HTTP protocol/HTTPS protocol. Before You Start The event alarm IP address or domain name should support the HTTP protocol/HTTPS protocol to receive the alarm information. Note The function should be supported by the device. Steps 1. Click Configuration → Network → Advanced → HTTP Listening . 2.
DS-K5671B Series Face Recognition Terminal User Manual Figure 8-8 Video Settings Page Set the video channel, camera name, stream type, the video type, the bitrate type, the frame rate, the Max. bitrate, the video encoding, and I Frame Interval. Click Save to save the settings after the configuration. Set Audio Parameters Click Configuration → Video/Audio → Audio . Select the audio channel. You can also drag the block to adjust the device input and output volume. Click to enable Voice Prompt.
DS-K5671B Series Face Recognition Terminal User Manual 8.6.15 Customize Audio Content Customize the output audio content when authentication succeeded and failed. Steps 1. Click Configuration → Video/Audio → Prompt . Figure 8-9 Customize Audio Content 2. Select Prompt as TTS(Text to Speech) to turn the text to audio content. 3. Select time schedule. 4. Enable the function. 5. Set the appellation. 6. Set the time period when authentication succeeded. 1) Click Add. 2) Set the time duration and the language.
DS-K5671B Series Face Recognition Terminal User Manual 5) Optional: Click to delete the configured time duration. 7. Set the time duration when authentication failed. 1) Click Add. 2) Set the time duration and the language. Note If authentication is failed in the configured time duration, the device will broadcast the configured content. 3) Enter the audio content. 4) Optional: Repeat substep 1 to 3. 5) Optional: Click to delete the configured time duration. 8. Optional: Add holiday schedule.
DS-K5671B Series Face Recognition Terminal User Manual Start/end recording video. Capture the image. Click Default to restore the parameters to the default settings. 3. 8.6.
DS-K5671B Series Face Recognition Terminal User Manual Set Manual Attendance via Web Set the attendance mode as manual, and you should select a status manually when you take attendance. Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Click Configuration → Attendance to enter the settings page. 2. Set the Attendance Mode as Manual. 3. Enable the Attendance Status Required and set the attendace status lasts duration. 4.
DS-K5671B Series Face Recognition Terminal User Manual Set Manual and Auto Attendance via Web Set the attendance mode as Manual and Auto, and the system will automatically change the attendance status according to the configured schedule. At the same time you can manually change the attendance status after the authentication. Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Click Configuration → Attendance to enter the settings page.
DS-K5671B Series Face Recognition Terminal User Manual Main Card Reader You can configure the device card reader's parameters. Sub Card Reader You can configure the connected peripheral card reader's parameters. If select Main Card Reader: Card Reader Type/Card Reader Description Get card reader type and description. They are read-only. Enable Card Reader Enable the card reader's function. Authentication Select an authentication mode according to your actual needs from the drop-down list.
DS-K5671B Series Face Recognition Terminal User Manual Select an authentication mode according to your actual needs from the drop-down list. Multiple People Authentication Multiple people can be authenticated at the same time. Recognition Interval If the interval between card presenting of the same card is less than the configured value, the card presenting is invalid. Alarm of Max. Failed Attempts Enable to report alarm when the card reading attempts reach the set value. Max.
DS-K5671B Series Face Recognition Terminal User Manual The earliest 5% events will be deleted when the system detects the stored events has been over 95% of the full space. Authentication Settings Display Authentication Result You can check Face Picture, Name, and Employee ID, to display the authentication result. Picture Uploading and Storage Upload Captured Picture When Authenticating Upload the pictures captured when authenticating to the platform automatically.
DS-K5671B Series Face Recognition Terminal User Manual Set Card Security Click Configuration → General → Card Security to enter the settings page. Set the parameters and click Save. Enable M1 Card Enable M1 card and authenticating by presenting M1 card is available. M1 Card Encryption Sector M1 card encryption can improve the security level of authentication. Enable the function and set the encryption sector. By default, Sector 13 is encrypted. It is recommended to encrypt sector 13.
DS-K5671B Series Face Recognition Terminal User Manual 8.6.19 Video Intercom Settings Set Video Intercom Parameters The device can be used as a door station, outer door station, or access control device. You should set the device No. before usage. Click Configuration → Intercom → Device No. . If set the device type as Door Station or Access Control Device, you can set the floor No., door station No., and click Advanced Settings to set Community No., Building No., and Unit No.
DS-K5671B Series Face Recognition Terminal User Manual Door Station No. Set the device installed floor No. ● ● Note If you change the No., you should reboot the device. The main door station No. is 0, and the sub door station No. ranges from 1 to 16. Community No. Set the device community No. Building No. Set the device building No. Unit No. Set the device unit No. Note If you change the No., you should reboot the device. If set the device type as Outer Door Station, you can set the period No.
DS-K5671B Series Face Recognition Terminal User Manual Click Save. Press Button to Call Steps 1. Click Intercom → Press Button to Call to enter the settings page. 2. Check Call Indoor Station, Call Specified Indoor Station, Call Management Center or APP at your needs. Note If you check Call Specified Indoor Station, you need to enter the number of the indoor station. 8.6.20 Access Control Settings Set Door Parameters Click Configuration → Access Control → Door Parameters .
DS-K5671B Series Face Recognition Terminal User Manual Select the device corresponded door No. Name You can create a name for the door. Open Duration Set the door unlocking duration. If the door is not opened for the set time, the door will be locked. Door Open Timeout Alarm An alarm will be triggered if the door has not been closed within the configured time duration. Door Contact You can set the door contact as Remain Open or Remain Closed according to your actual needs. By default, it is Remain Closed.
DS-K5671B Series Face Recognition Terminal User Manual Figure 8-12 Access Control and Elevator Control 2. Check Enable Elevator Control. 3. Set the elevator parameters. Elevator No. Select an elevator No. for configuration from the drop-down list. Elevator Controller Type Select an elevator controller from the drop-down list. Interface Type Select a communication type from the drop-down list for elevator communication.
DS-K5671B Series Face Recognition Terminal User Manual Click Configuration → Access Control → RS-485 Settings . Check Enable RS-485, and set the parameters. Click Save to save the settings after the configuration. No. Set the RS-485 No. Peripheral Type Select a peripheral from the drop-down list according the actual situation. You can select from Card Reader, Extension Module, Access Controller, or Disable. Note After the peripheral is changed and saved, the device will reboot automatically.
DS-K5671B Series Face Recognition Terminal User Manual Figure 8-13 Wiegand Page 2. Check Wiegand to enable the Wiegand function. 3. Set a transmission direction. Input The device can connect a Wiegand card reader. Output The can connect an external access controller. And the two devices will transmit the card No. via Wiegand 26 or 34. 4. Click Save to save the settings. Note If you change the peripheral, and after you save the device parameters, the device will reboot automatically. 8.6.
DS-K5671B Series Face Recognition Terminal User Manual Figure 8-14 Smart Settings Page Click Save to save the settings after the configuration.
DS-K5671B Series Face Recognition Terminal User Manual Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not. Note Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes.
DS-K5671B Series Face Recognition Terminal User Manual Enable Hard Hat Detection After enabling the hard hat detection, you can set the strategy. None The function is disabled. The device will not detect whether a person is wearing a hard hat or not. Reminder of Wearing If the person do not wear the hard hat when authenticating, the device will pop up a prompt and the door will open.
DS-K5671B Series Face Recognition Terminal User Manual Face with Mask 1:N Matching Threshold (ECO Mode) Set the matching threshold when authenticating with face mask via ECO mode 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. Set Recognition Area Click Configuration → Smart → Area Configuration . Drag the yellow frame in the live video to adjust the recognition area. Only the face within the area can be recognized by the system.
DS-K5671B Series Face Recognition Terminal User Manual Slide Show Interval Drag the block or enter the number to set the slide show interval. The picture will be changed according to the interval. Add Media Click Configuration → Media Database . Click Add and select picture to add to the media database. Click Upload.
DS-K5671B Series Face Recognition Terminal User Manual Chapter 9 Client Software Configuration 9.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software. Figure 9-1 Flow Diagram of Configuration on Client Software 9.2 Device Management The client supports managing access control devices and video intercom devices.
DS-K5671B Series Face Recognition Terminal User Manual Example You can control entrance & exit and manage attendance after adding access control devices to the client; you can perform video intercom with the indoor stations and door stations. 9.2.1 Add Device The client provides three device adding modes including by IP/domain, IP segment, and ISUP protocol. The client also supports importing multiple devices in a batch when there are large amount of devices to be added.
DS-K5671B Series Face Recognition Terminal User Manual 3. In the Online Device area, check one or more online device(s), and click Add to open the device adding window. Figure 9-3 Add Single Online Device Figure 9-4 Add Multiple Online Devices 4. Enter the required information.
DS-K5671B Series Face Recognition Terminal User Manual Name Enter a descriptive name for the device. IP Address Enter the device's IP address. The IP address of the device is obtained automatically in this adding mode. Port You can customize the port number. The port number of the device is obtained automatically in this adding mode. User Name By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked.
DS-K5671B Series Face Recognition Terminal User Manual Add Multiple Detected Online Devices For detected online devices sharing the same user name and password, you can add them to the client in a batch. Before You Start Make sure the to-be-added devices are online. Steps 1. Enter the Device Management module. 2. Click Device tab on the top of the right panel. 3. Click Online Device to show the online device area at the bottom of the page. The searched online devices are displayed in the list. 4.
DS-K5671B Series Face Recognition Terminal User Manual 9. Click Add to add the devices. Add Device by IP Address or Domain Name If you know the IP address or domain name of the device to add, you can add devices to the client by specifying the IP address (or domain name), user name, password, etc. Steps 1. Enter Device Management module. 2. Click Device tab on the top of the right panel. The added devices are displayed on the right panel. 3.
DS-K5671B Series Face Recognition Terminal User Manual Note ● This function should be supported by the device. ● If you have enabled Certificate Verification, you should click Open Certificate Directory to open the default folder, and copy the certificate file exported from the device to this default directory to strengthen the security. See for details about enabling certificate verification. ● You can log into the device to get the certificate file by web browser. 6.
DS-K5671B Series Face Recognition Terminal User Manual Enter the device password. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K5671B Series Face Recognition Terminal User Manual Device Account Enter the account name registered on ISUP protocol. ISUP Key For ISUP 5.0 devices, enter the ISUP key if you have set it when configuring network center parameter for the device. Note This function should be supported by the device. 5. Optional: Check Synchronize Time to synchronize the device time with the PC running the client after adding the device to the client. 6.
DS-K5671B Series Face Recognition Terminal User Manual Adding Mode Enter 0 or 1 or 2. Address Edit the address of the device. Port Enter the device port number. The default port number is 8000. User Name Enter the device user name. By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked.
DS-K5671B Series Face Recognition Terminal User Manual Note For the following operations for resetting the password, contact our technical support. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K5671B Series Face Recognition Terminal User Manual 9.3.2 Import Resources to Group You can import the device resources (such as alarm inputs/outputs, access points, etc.) to the added group in a batch. Before You Start Add a group for managing devices. Refer to Add Group . Steps 1. Enter the Device Management module. 2. Click Device Management → Group to enter the group management page. 3. Select a group from the group list and select the resource type as Access Point, Alarm Input, Alarm Output, etc. 4.
DS-K5671B Series Face Recognition Terminal User Manual Steps 1. Enter the Device Management module. 2. Click Device Management → Group to enter the group management page. All the added groups are displayed on the left. 3. Click a group to show the resources added to this group. 4. Select the resource(s) and click Delete to remove the resource(s) from the group. 9.
DS-K5671B Series Face Recognition Terminal User Manual 9.4.2 Configure Basic Information You can add person to the client one by one and configure the person's basic information such as name, gender, email, phone number, etc. Steps 1. Enter Person module. Note For the first time you enter Person module, a window pops up, and you can set the rules to generate person ID (letters and numbers supported) when adding person.
DS-K5671B Series Face Recognition Terminal User Manual - Click Add and New to add the person and continue to add other persons. 9.4.3 Issue a Card by Local Mode If a card enrollment station is available, you can issue a card by local mode. To read the card number, you should connect the card enrollment station to the PC running the client by USB interface or COM, and place the card on the card enrollment station. Steps 1. Enter Person module. 2.
DS-K5671B Series Face Recognition Terminal User Manual Figure 9-6 Issue a Card by Local Mode 6. Set other related parameters. Card Enrollment Station Select the model of the connected card enrollment station. Note Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100M, DS-K1F100-D8E, and DS-K1F180-D8E. Card Type This field is only available when the model is DS-K1F100-D8E or DS-K1F180-D8E. Select the card type as EM card or Mifare card according to the actual card type.
DS-K5671B Series Face Recognition Terminal User Manual Enable or disable the buzzing when the card number is read successfully. Card No. Type Select the type of the card number according to actual needs. M1 Card Encryption This field is only available when the model is DS-K1F100-D8, DS-K1F100-D8E, or DS-K1F180D8E. If the card is M1 card, then you can enable the M1 Card Encryption function and select the sector of the card to encrypt. 7. Click OK to confirm the operation. 8.
DS-K5671B Series Face Recognition Terminal User Manual 9.4.5 Take a Photo via Client When adding a person, you can take a photo of the her/him via the client and set this photo as the person's profile. Before You Start Make sure PC running the client has a camera or you have connected other USB camera to the PC. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add to enter Add Person window. Note Enter the person's basic information first.
DS-K5671B Series Face Recognition Terminal User Manual Figure 9-7 Take a Photo via Client 7. Confirm to add the person. - Click Add to add the person and close the Add Person window. - Click Add and New to add the person and continue to add other persons. 9.4.6 Collect Face via Access Control Device When adding person, you can collect the person's face via access control device added to the client which supports facial recognition function. Steps 1. Enter Person module. 2.
DS-K5671B Series Face Recognition Terminal User Manual Note If you select the enrollment station, you should click Login to set related parameters of the device including IP address, port No., user name, and password. Also, you can check Face AntiSpoofing and select the liveness level as Low, Medium, or High. Face Anti-Spoofing If you check this function, then the device can detect whether the face to be collected is an authentic one. 6. Collect face.
DS-K5671B Series Face Recognition Terminal User Manual Figure 9-8 Configure Access Control Information 4. Set a unique PIN code for the person which can be used for access authentication. - Manually enter a PIN code containing 4 to 8 digits. Note Persons' PIN codes cannot be repeated. - Click Generate to randomly generate an unrepeated PIN code of 6 digits. Note If there are repeated PIN codes, a prompt will pop up on the client.
DS-K5671B Series Face Recognition Terminal User Manual Note The valid times for visit is between 1 and 100. You can also check No Limit, then there are no limited times for the visitor to access doors/floors. Device Operator For person with device operator role, he/she is authorized to operate on the access control devices. Note The Super User, Extended Door Open Time, Add to Blocklist, and Mark as Visitor functions cannot be enabled concurrently.
DS-K5671B Series Face Recognition Terminal User Manual 9.4.9 Configure Resident Information If the person is resident, for video intercom purpose, you need to set the room number for her/him and bind an indoor station. After bound, you can call this person by calling the indoor station and perform video intercom with her/him. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add. Note Enter the person's basic information first.
DS-K5671B Series Face Recognition Terminal User Manual 9.4.11 Import and Export Person Identify Information You can import the information and pictures of multiple persons to the client software in a batch. Meanwhile, you can also export the person information and pictures and save them in your PC. 9.4.12 Import Person Information You can enter the information of multiple persons in a predefined template (CSV/Excel file) to import the information to the client in a batch. Steps 1. Enter the Person module.
DS-K5671B Series Face Recognition Terminal User Manual 2. Select an added organization in the list, or click Add in the upper-left corner to add an organization and then select it. 3. Click Import to open the Import panel and check Face. 4. Optional: Enable Verify by Device to check whether face recognition device managed in the client can recognize the face in the photo. to select a face picture file. 5. Click Note ● The (folder of) face pictures should be in ZIP format.
DS-K5671B Series Face Recognition Terminal User Manual Note All persons' face pictures will be exported if you do not select any organization. 3. Click Export to open the Export panel and check Face as the content to export. 4. Click Export to start exporting. ● ● Note The exported file is in ZIP format. The exported face picture is named as "Person ID_Name_0" ("0" is for a full-frontal face). 9.4.16 Delete Registered Pictures You can delete face picture file of the added persons automatically.
DS-K5671B Series Face Recognition Terminal User Manual Note If you select the enrollment station, you should click Login, and set IP address, port No., user name and password of the device. 5. Click Import to start importing the person information to the client. Note Up to 2,000 persons and 5,000 cards can be imported. The person information, including person details, and the linked cards (if configured), will be imported to the selected organization. 9.4.
DS-K5671B Series Face Recognition Terminal User Manual - Place the card on the card enrollment station. - Swipe the card on the card reader. - Manually enter the card number and press the Enter key. The person(s) in the list will be issued with card(s). 9.4.20 Report Card Loss If the person lost his/her card, you can report the card loss so that the card's related access authorization will be inactive. Steps 1. Enter Person module. 2.
DS-K5671B Series Face Recognition Terminal User Manual Note Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100-M, DS-K1F100-D8E, and DS-K1F180-D8E. Card Type This field is only available when the model is DS-K1F100-D8E or DS-K1F180-D8E. Select the card type as EM card or IC card according to the actual card type. Serial Port It is only available when the model is DS-K1F100-M. Select the COM the card enrollment station connects to.
DS-K5671B Series Face Recognition Terminal User Manual Steps Note You can add up to 64 holidays in the software system. 1. Click Access Control → Schedule → Holiday to enter the Holiday page. 2. Click Add on the left panel. 3. Create a name for the holiday. 4. Optional: Enter the descriptions or some notifications of this holiday in the Remark box. 5. Add a holiday period to the holiday list and configure the holiday duration. Note Up to 16 holiday periods can be added to one holiday.
DS-K5671B Series Face Recognition Terminal User Manual 1. Click Access Control → Schedule → Template to enter the Template page. Note There are two default templates: All-Day Authorized and All-Day Denied, and they cannot be edited or deleted. All-Day Authorized The access authorization is valid in each day of the week and it has no holiday. All-Day Denied The access authorization is invalid in each day of the week and it has no holiday. 2. Click Add on the left panel to create a new template. 3.
DS-K5671B Series Face Recognition Terminal User Manual 9.6 Set Access Group to Assign Access Authorization to Persons After adding the person and configuring the person's credentials, you can create the access groups to define which person(s) can get access to which door(s) and then apply the access group to the access control device to take effect. Steps When the access group settings are changed, you need to apply the access groups to the devices again to take effect.
DS-K5671B Series Face Recognition Terminal User Manual Figure 9-9 Display the Selected Person(s) and Access Point(s) 8. After adding the access groups, you need to apply them to the access control device to take effect. 1) Select the access group(s) to apply to the access control device. 2) Click Apply All to Devices start applying all the selected access group(s) to the access control device or door station. 3) Click Apply All to Devices or Apply Changes to Devices.
DS-K5671B Series Face Recognition Terminal User Manual Note If you change the persons' access information or other related information, you will view the promptAccess Group to Be Applied on the right corner of the client. You can click the prompt to apply the changed data to the device. You can select either Apply Now or Apply Later. Figure 9-11 Data Synchronization 9.
DS-K5671B Series Face Recognition Terminal User Manual Configure Parameters for Access Control Device After adding the access control device, you can configure its parameters, including overlaying user information on picture, uploading pictures after capturing, saving captured pictures, etc. Steps 1. Click Access Control → Advanced Function → Device Parameter .
DS-K5671B Series Face Recognition Terminal User Manual Note If the peripheral card reader supports presenting EM card, the function is also supported to enable/disable the EM card function. 4. Click OK. 5. Optional: Click Copy to, and then select the access control device(s) to copy the parameters in the page to the selected device(s). Configure Parameters for Door After adding the access control device, you can configure its access point door parameters. Steps 1.
DS-K5671B Series Face Recognition Terminal User Manual Extended Open Duration The door contact can be enabled with appropriate delay after person with extended accesss needs swipes her/his card. Duress Code The door can open by inputting the duress code when there is duress. At the same time, the client can report the duress event. Note ● The duress code and the super code should be different. ● The duress code and super password should be different from the authentication password.
DS-K5671B Series Face Recognition Terminal User Manual Alarm of Max. Failed Attempts Enable to report alarm when the card reading attempts reach the set value. Card Reader Type/Card Reader Description Get card reader type and description. They are read-only. Advanced Enable Card Reader Enable the function and e device can be used as an card reader.
DS-K5671B Series Face Recognition Terminal User Manual After enabling the Live Face Detection function, the system will lock the user's face for 5 minutes if the live face detection is failed for more than the configured attempts. The same user cannot authenticate via the fake face within 5 minutes. Within the 5 minutes, the user can authenticate via the real face twice continuously to unlock.
DS-K5671B Series Face Recognition Terminal User Manual 2. Select the door that need to be configured on the left panel. 3. To set the door status during the work day, click the Week Schedule and perform the following operations. 1) Click Remain Open or Remain Closed. 2) Drag the cursor to draw the time duration, which means in that duration of time, the configured access group is activated. Note Up to 8 time durations can be set to each day in the week schedule.
DS-K5671B Series Face Recognition Terminal User Manual 8) Optional: Click in the Operation column to delete this added holiday period from the holiday list. 9) Click Save. 5. Optional: Click Copy to to copy the door status settings of this door to other door(s). 9.7.3 Configure Multi-Factor Authentication You can manage the persons by group and set the authentication for multiple persons of one access control point (door).
DS-K5671B Series Face Recognition Terminal User Manual 3) Select the authentication type as Local Authentication, Local Authentication and Remotely Open Door, or Local Authentication and Super Password from the drop-down list. Local Authentication Authentication by the access control device. Local Authentication and Remotely Open Door Authentication by the access control device and by the client. When the person swipes the card on the device, a window will pop up. You can unlock the door via the client.
DS-K5671B Series Face Recognition Terminal User Manual Note ● For each access control point (door), up to four authentication groups can be added. ● For the authentication group of which authentication type is Local Authentication, up to 8 person/card groups can be added to the authentication group.
DS-K5671B Series Face Recognition Terminal User Manual Figure 9-13 Select Card Reader Authentication Mode Note PIN refers to the PIN code set to open the door. Refer to Configure Access Control Information . 2) Check the modes in the Available Mode list and they will be added to the selected modes list. 3) Click OK. After selecting the modes, the selected modes will display as icons with different color. 4.
DS-K5671B Series Face Recognition Terminal User Manual Figure 9-14 Set Authentication Modes for Card Readers 6. Optional: Select a configured day and click Copy to Week to copy the same settings to the whole week. 7. Optional: Click Copy to to copy the settings to other card readers. 8. Click Save. 9.7.5 Configure First Person In You can set multiple first persons for one access control point. After the first person is authorized, it allows multiple persons access the door or other authentication actions.
DS-K5671B Series Face Recognition Terminal User Manual The door remains open for the configured time duration after the first person is authorized until the remain open duration ends. If you select this mode, you should set the remain open duration. Note The remain open duration should be between 0 and 1440 minutes. By default, the remain open duration is 10 minutes. Disable Remaining Open after First Person Disable the function of first person in, namely normal authentication.
DS-K5671B Series Face Recognition Terminal User Manual 4. Click of the selected first card reader in the Card Reader Afterward column to open the select card reader dialog. 5. Select the afterward card readers for the first card reader. Note Up to four afterward card readers can be added as afterward card readers for one card reader. 6. Click OK in the dialog to save the selections. 7. Click Save in the Anti-Passback Settings page to save the settings and take effect.
DS-K5671B Series Face Recognition Terminal User Manual The maximum transmission unit (MTU) of the network interface. Click Save. 6. Set Network Parameters After adding the access control device, you can set the device log uploading mode, and create ISUP account via wired network. Set Log Uploading Mode You can set the mode for the device to upload logs via ISUP protocol. Steps 1. Enter the Access Control module. 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3.
DS-K5671B Series Face Recognition Terminal User Manual Note The port number of the wireless network and wired network should be consistent with the port number of ISUP. 8. Select the Protocol Type as ISUP. Note If set the ISUP version as 5.0, you should create an ISUP key for the ISUP account. 9. Set an account name for the network center. 10. Click Save.
DS-K5671B Series Face Recognition Terminal User Manual 5. Set the capture times once triggered which defines how many pictures will be captures for one time. 6. If the capture times is more than 1, set the interval for each capture. 7. Click Save. Set Manual Capture Parameters In Status Monitoring module, you can capture a picture manually the access control device's camera by clicking a button. Before that, you need to set the parameters for the capture such as picture quality.
DS-K5671B Series Face Recognition Terminal User Manual Note These parameters displayed vary according to different device models. Algorithm Select Deep Learning as the face picture database. Save Authentication Picture If enabled, the captured face picture when authenticating will be saved on the device. ECO Mode After enabling the ECO mode, the device can authenticate faces in the low light or dark environment. And you can set he ECO mode threshold, ECO mode (1:N), and ECO mode (1:1).
DS-K5671B Series Face Recognition Terminal User Manual 3. Select an access control device in the device list and click M1 Card Encryption Verification to enter the M1 Card Encryption Verification page. 4. Set the switch to on to enable the M1 card encryption function. 5. Set the sector ID. Note ● The sector ID ranges from 1 to 100. ● By default, Sector 13 is encrypted. It is recommended to encrypt sector 13. 6. Click Save to save the settings.
DS-K5671B Series Face Recognition Terminal User Manual 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3. Select an access control device in the device list and click Wiegand to enter the Wiegand Settings page. 4. Set the switch to on to enable the Wiegand function for the device. 5. Select the Wiegand channel No. and the communication mode from the drop-down list.
DS-K5671B Series Face Recognition Terminal User Manual 3. Select the event(s) and click Edit Priority to define the priority for the event(s), which can be used to filter events in the Event Center. 4. Set the linkage actions of the event. 1) Select the event(s) and click Edit Linkage to set the client actions when the event(s) are triggered. Audible Warning The client software gives an audible warning when the event is triggered. You can select alarm sound for the audible warning.
DS-K5671B Series Face Recognition Terminal User Manual Capture The real-time capture will be triggered. Access Point The door status of open, close, remain open, and remain close will be triggered. Note The target door and the source door cannot be the same one. 7. Click Save. 8.
DS-K5671B Series Face Recognition Terminal User Manual 9. Optional: After adding the device linkage, you can do one or more of the following: Delete Linkage Settings Select the configured linkage settings in the device list and click Delete to delete it. Edit Linkage Settings Select the configured linkage settings in the device list and you can edit its event source parameters, including event source and linkage target. 9.8.
DS-K5671B Series Face Recognition Terminal User Manual Delete Linkage Settings Select the configured linkage settings in the device list and click Delete to delete it. Edit Linkage Settings Select the configured linkage settings in the device list and you can edit its event source parameters, including event source and linkage target. 9.9 Door Control In Monitoring module, you can view the real-time status of the doors managed by the added access control device.
DS-K5671B Series Face Recognition Terminal User Manual Unlock When the door is locked, unlock it and it will be open for once. After the open duration, the door will be closed and locked again automatically. Lock When the door is unlocked, lock it and it will be closed. The person who has the access authorization can access the door with credentials. Remain Unlocked The door will be unlocked (no matter closed or open). All the persons can access the door with no credentials required.
DS-K5671B Series Face Recognition Terminal User Manual 2. Optional: Check the event type and event status so that these events will show in the list if the events are detected. The events of unchecked type or status will not be displayed in the list. 3. Optional: Check Show Latest Event and the latest access record will be selected and displayed at the top of the record list. 4.
DS-K5671B Series Face Recognition Terminal User Manual Figure 9-15 Arm Device After turned on, the device(s) will be armed. And notifications about the events triggered by the armed device(s) will be automatically sent to the client software in real-time. 9.10.2 View Real-Time Events The real-time event information received by the client of the connected resources are displayed. You can check the real-time event information, including event source, event time, priority, etc.
DS-K5671B Series Face Recognition Terminal User Manual Filter by Device Type and (or) Priority Select device type(s) and (or) priorities to filter events. Filter by Keywords Enter the keywords to filter the events. Optional: Right-click the table header of the event list to customize the event related items to be 3. displayed in the event list. 4. View the event details. 1) Select an event in the event list. 2) Click Expand in the right-lower corner of the page.
DS-K5671B Series Face Recognition Terminal User Manual Steps 1. Click Event Center → Event Search to enter the event search page. 2. Set the filter conditions to display the required events only. Time The time when the event starts. Search by Device Search the events by device or the device's resource channels. If searched by device, you need to set the followings: ● Include Sub-Node: Search the events of the device and all resource channels.
DS-K5671B Series Face Recognition Terminal User Manual Figure 9-16 Search Historical Events Note If you have selected Access Control as device type in Step 2, you can view extra information such as card No., skin-surface temperature, and abnormal temperature (if device supports) in the searched events.
DS-K5671B Series Face Recognition Terminal User Manual Figure 9-17 Search Historical Event 4. Optional: Right click the table header of the event list to customize the event related items to be displayed in the event list. 5. Select an event in the event list to view the event details. 6. Optional: Perform one of the following operations.
DS-K5671B Series Face Recognition Terminal User Manual Auto-Play Video Enlarge Video or Picture Send Email Check Auto-Play Video to automatically play video when displaying event details. ● ● Double click the video image to view video in a larger window. Put the cursor on the picture, and click to view picture in a larger window. Select an event and then click Send Email, and the information details of this event will be sent by email.
DS-K5671B Series Face Recognition Terminal User Manual Steps Note The parameters configured here will be set as default for the newly added time period. It will not affect the existed one(s). 1. Enter Time & Attendance module. 2. Click Attendance Settings → General Rule . 3. Select the day(s) as weekend, such as Saturday and Sunday. 4. Click Save.
DS-K5671B Series Face Recognition Terminal User Manual By default, all card readers of the added access control devices are set as start/end-work check points. If you need to edit check point function of card reader(s), you can perform the following operations. Steps 1. Enter the Time & Attendance module. 2. Click Attendance Settings → Attendance Check Point to enter the attendance check point settings page. 3. Set Set All Card Readers as Check Points switch to off. 4.
DS-K5671B Series Face Recognition Terminal User Manual Add Regular Holiday You can configure a holiday which will take effect annually on regular days during the effective period, such as New Year's Day, Independence Day, Christmas Day, etc. Steps 1. Enter the Time & Attendance module. 2. Click Attendance Settings → Holiday to enter the Holiday Settings page. 3. Check Regular Holiday as holiday type. 4. Custom a name for the holiday. 5. Set the first day of the holiday. 6.
DS-K5671B Series Face Recognition Terminal User Manual 10. Click OK. The added holiday will display in the holiday list and calendar. If the date is selected as different holidays, it will be recorded as the first-added holiday. 11. Optional: After adding the holiday, perform one of the following operations. to edit the holiday information. Edit Holiday Click Delete Holiday Select one or more added holidays, and click Delete to delete the holiday(s) from the holiday list.
DS-K5671B Series Face Recognition Terminal User Manual Note If you select MySQL, you should import the configuration file (libmysql.dll) from local PC. 5. Set the other required parameters of the third-party database, including server IP address, port No., database name, user name and password. Note The default port No. of the selected database type is displayed automatically. You can enter a number ranging from 1 to 65535 to customize the port No if needed. 6.
DS-K5671B Series Face Recognition Terminal User Manual Must Check The break duration will be calculated and excluded from work hours according to actual check-in and check-out time. Return from Break Early for The actual check-in and check-out time does not exceed the break time, and can be marked as normal work or work overtime. Return from Break Late for The actual check-in and check-out time exceeds the break time, and can be marked as late, absent or early leave.
DS-K5671B Series Face Recognition Terminal User Manual Enter the mark and select the color. The related fields of attendance status in the report will display with the mark and color. Weekend Mark Enter the mark and select the color. The weekend fields in the report will display with the mark and color. 4. Click Save. 9.11.2 Add General Timetable On the timetable page, you can add general timetable for employees, which requires the fixed start-work time and end-work time.
DS-K5671B Series Face Recognition Terminal User Manual Figure 9-18 Add Timetable 3. Create a name for the timetable. Note You can click the color icon beside the name to customize the color for the valid timetable on the time bar in the Configuration Result area. 4. Select the timetable type as general. 5. Select calculation method. First In & Last Out The first check-in time is recorded as start work time and the last check-out time is recorded as the end-work time.
DS-K5671B Series Face Recognition Terminal User Manual You need to set Valid Authentication Interval for this calculation method. For example, if the interval between card swiping of the same card is less than the set value, the card swiping is invalid. 6. Optional: Set Enable T&A Status switch to on to calculate according to attendance status of the device. Note This function should be supported by the device. 7. Optional: Enable Calculate Break Time into Attended Duration.
DS-K5671B Series Face Recognition Terminal User Manual Delete Timetable Select a timetable from the list and click Delete to delete it. 9.11.3 Add Shift You can add shift for employees including setting shift period (day, week, month) and the effective attendance time. According to the actual requirements, you can adding multiple timetables in one shift for employees, which requires them to check in and check out for each timetable. Before You Start Add a timetable first.
DS-K5671B Series Face Recognition Terminal User Manual Figure 9-19 Add Shift Note You can select more than one timetables. The start and end work time and the valid check-in and out time in different time tables can not be overlapped.
DS-K5671B Series Face Recognition Terminal User Manual Figure 9-20 Add Multiple Timetables 6. Click Save. The added shift lists on the left panel of the page. At most 64 shifts can be added. 7. Optional: Assign the shift to organization or person for a quick shift schedule. 1) Click Assign. 2) Select Organization or Person tab and check the desired organization(s) or person(s) box. The selected organizations or persons will list on the right page. 3) Set the Expire Date for the shift schedule.
DS-K5671B Series Face Recognition Terminal User Manual On the holidays, this schedule is still effective and the persons needs to go to work according to the schedule. Effective for Overtime The persons' overtime will be recorded for this schedule. 5) Click Save to save the quick shift schedule. 9.11.4 Manage Shift Schedule Shift work is an employment practice designed to make use of all 24 hours of the clock each day of the week.
DS-K5671B Series Face Recognition Terminal User Manual If the multiple shift schedules contains three timetables: 00:00 to 07:00, 08:00 to 15:00 and 16:00 to 23:00. The attendance of the person adopting this multiple shift schedules will be effective in any of the three timetables. If the person checks in at 07:50, it will apply the nearest timetable 08:00 to 15:00 to the person's attendance. 6. Set the start date and end date. 7. Set other parameters for the schedule.
DS-K5671B Series Face Recognition Terminal User Manual Note This is only available for shift with only one timetable. Multiple Shift Schedules It contains more than one timetables. The person can check in/out in any of the timetables and the attendance will be effective. If the multiple shift schedules contains three timetables: 00:00 to 07:00, 08:00 to 15:00 and 16:00 to 23:00. The attendance of the person adopting this multiple shift schedules will be effective in any of the three timetables.
DS-K5671B Series Face Recognition Terminal User Manual 4. Click one date or click and drag to select multiple dates for the temporary schedule. 5. Select Workday or Non-Workday from drop-down list. If Non-Workday is selected, you need to set the following parameters. Calculated as Select normal or overtime level to mark the attendance status for temporary schedule. Timetable Select a timetable from drop-down list. Multiple Shift Schedule It contains more than one timetables.
DS-K5671B Series Face Recognition Terminal User Manual Before You Start ● You should add organizations and persons in Person module. For details, refer to Person Management . ● The person's attendance status is incorrect. Steps 1. Click Time & Attendance → Attendance Handling to enter attendance handling page. 2. Click Correct Check-in/out to enter adding check-in/out correction page. 3. Select one or more persons from left list for correction. 4. Select the correction date. 5.
DS-K5671B Series Face Recognition Terminal User Manual Before You Start You should add organizations and persons in the Person module. For details, refer to Person Management . Steps 1. Click Time & Attendance → Attendance Handling to enter attendance handling page. 2. Click Apply for Leave/Business Trip to enter adding the leave/business trip page. 3. Select person from left list. 4. Set the date(s) for your leave or business trip. 5.
DS-K5671B Series Face Recognition Terminal User Manual Automatically Calculate Attendance Data You can set a schedule so that the client can automatically calculate attendance data of the previous day at the time you configured every day. Steps Note 1. Enter the Time & Attendance module. 2. Click Attendance Settings → General Rule . 3. In the Auto-Calculate Attendance area, set the time that you want the client to calculate the data. 4. Click Save.
DS-K5671B Series Face Recognition Terminal User Manual Note The report items will be displayed in the sequence you have set. Export Report Click Export to export attendance data (CSV file) to local PC. Note The report items will be displayed in the sequence you have set. 9.11.8 Attendance Statistics You can check the original attendance record, generate and export the attendance report based on the calculated attendance data.
DS-K5671B Series Face Recognition Terminal User Manual Note There are two methods for getting attendance events from the device, including Online and Import File. For more details about operations, refer to Get Events from Device in the user manual of the client software. 7. Optional: Click Reset to reset all the search conditions and edit the search conditions again. 8. Click Search. 9. Optional: For the displayed search results, perform one of the following operations.
DS-K5671B Series Face Recognition Terminal User Manual Send Report Regularly The client supports multiple report types and you can pre-define the report content and it can send the report automatically to the email address you configured. Steps 1. Enter the Time & Attendance module. 2. Click Attendance Statistics → Regularly Send Report . 3. Click Add to enter the add custom report page. 4. Set the report content. Report Name Enter a name for the report.
DS-K5671B Series Face Recognition Terminal User Manual Note Up to 5 email addresses can be added. You can click + to add a new email address. 5) Optional: Click Preview to view the email details. 6. Click OK. 7. Optional: After adding the custom report, you can do one or more of the followings: Edit Report Select one added report and click Edit to edit its settings. Delete Report Select one added report and click Delete to delete it.
DS-K5671B Series Face Recognition Terminal User Manual Save Event for Set the event deleting cycle to delete the old event. Detect New Software Version After enabled, the client can automatically detect the new software version and remind the user to upgrade the software. Automatic Time Synchronization Automatically synchronize the time of the added devices with the time of the PC running the client at a specified time point.
DS-K5671B Series Face Recognition Terminal User Manual Note The default saving path is: Disk/iVMS-4200alarmPicture 5. Click Save. 9.12.3 Set Alarm Sound When the event is triggered, the client can give an audible warning to notify the security personnel. You can set the sound of the audible warning in this section. Steps 1. Open the System Configuration page. 2. Click Alarm Sound tab to enter the Alarm Sound Settings page. 3.
DS-K5671B Series Face Recognition Terminal User Manual Specify the seconds that the call with indoor station will last for at most. The maximum speaking duration between indoor station and the client can be set from 120s to 600s. Max. Speaking Duration with Door Station Specify the seconds that the call with door station will last for at most. The maximum speaking duration between door station and the client can be set from 90s to 120s. Max.
DS-K5671B Series Face Recognition Terminal User Manual Security Certificate (Optional) If your email server requires authentication, check this checkbox to use authentication to log into the server and enter the login user name and password of your email account. User Name Enter the user name of the sender email address if Server Authentication is checked. Password Enter the password of the sender Email address if Server Authentication is checked. Receiver 1 to 3 Enter the email address of the receiver.
DS-K5671B Series Face Recognition Terminal User Manual Appendix A. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Positions (Recommended Distance: 0.5 m) Expression ● ● ● Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function. Do not make your hair cover your eyes, ears, etc.
DS-K5671B Series Face Recognition Terminal User Manual Size Make sure your face is in the middle of the collecting window.
DS-K5671B Series Face Recognition Terminal User Manual Appendix B. Tips for Installation Environment 1. Light Source Illumination Reference Value Candle: 10Lux Bulb: 100~850Lux Sunlight: More than 1200Lux 2. Install the device at least 2 meters away from the light, and at least 3 meters away from the window or door. 3.
DS-K5671B Series Face Recognition Terminal User Manual Appendix C.
DS-K5671B Series Face Recognition Terminal User Manual Appendix D. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure D-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD27224B-B
