FocSign Lite Client User Manual FocSign Lite Client User Manual i
FocSign Lite Client User Manual © 2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. This Manual is the property of Hangzhou Hikvision Digital Technology Co., Ltd. or its affiliates (hereinafter referred to as "Hikvision"), and it cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
FocSign Lite Client User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
FocSign Lite Client User Manual Applicable Models This manual is applicable to FocSign Lite. Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Provides additional information to emphasize or supplement important points of the main text. Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
FocSign Lite Client User Manual TABLE OF CONTENTS Chapter 1 Product Introduction...................................................................................................................................................... 1 1.1 Introduction ...............................................................................................................................................................................1 1.2 Operation Flowchart ............................................................
FocSign Lite Client User Manual 4.2.2 Create Loop Schedule ...................................................................................................................................................24 4.3 Release .....................................................................................................................................................................................25 4.3.1 Release Program ....................................................................................
FocSign Lite Client User Manual Chapter 1 Product Introduction 1.1 Introduction FocSign Lite client (hereinafter referred to as the client) is used to create programs and release them to information release screen or digital signage (hereinafter they are referred to as the terminal). The client supports program creation, release management, broadcast schedule management, cut-in, terminal management, etc. 1.
FocSign Lite Client User Manual Chapter 2 Registration and Login 2.1 Registration Purpose: Registration is required for the first login. Before you start: Install the client on your computer. Step 1 Run the client. Step 2 Set the password and confirm it. One client has only one user: admin. Step 3 Click Register. You will enter the interface of Port Settings. Click OK if the message which requires you to disable the firewall appears.
FocSign Lite Client User Manual Enter the password and click Login. You can manage and release program to the terminal after logging in. Figure 2-1 Log In Click on the home page to edit login password or enable/disable auto login.
FocSign Lite Client User Manual Chapter 3 Terminal Management 3.1 Add Terminal Purpose: You can manage added terminals, including start up/shut down terminals, adjust terminal volume and brightness, etc. You can add terminal via the following methods: Add terminals from the Online Terminal bar if the client and the terminals are in the same network segment. Add terminals by IP address. Add terminals by serial number. 3.1.
FocSign Lite Client User Manual Figure 3-1 Activate Terminal Step 5 Set the terminal password and confirm password. Step 6 Click OK. Register Terminal Purpose: You can register activated terminal to the client. Before you start: Ensure the terminal and the client are in the same network segment. Step 1 Go to Terminal Management. Step 2 Click on the lower-right corner. Step 3 Select the terminals to register. Step 4 Click CMS Registration.
FocSign Lite Client User Manual Step 5 Set IP type, IP address, and server port. Step 6 Enter terminal password. Step 7 Click OK. Step 8 Optionally, click Acquire Registration Status to view terminal registration status. 3.1.2 Add Terminal by IP Address Step 1 Go to Terminal Management. Step 2 Click Add Terminal. Figure 3-2 Add Terminal Step 3 Select Adding Mode as Add by IP. Step 4 Enter Terminal IP Address and Port. Step 5 Enter Terminal Name and Terminal Password. Step 6 Click OK. 3.1.
FocSign Lite Client User Manual Figure 3-3 Add Terminal by Serial No. Step 4 Enter Terminal Name, Terminal Serial No. , Authentication Code, and Description. Step 5 Click OK. Step 6 Register the terminal to be added. 1) 2) 3) 4) 5) 6) Open the information release software in the terminal. Double click upper-right corner. Enter the terminal name and information of server. Click Next. Enter the authorization code set in Step 4. Click OK. 3.1.
FocSign Lite Client User Manual 3.1.5 View Terminal Details Click of a terminal to view its information and current program image. 3.2 Terminal Operation Purpose: You can start up/shut down terminal, adjust terminal volume, and control program via terminal operation menu. 3.2.1 Startup and Shutdown Purpose: You can manually start up and shut down a terminal, and configure the startup/shutdown schedule for a terminal. : Start up the selected terminal. : Shut down the selected terminal.
FocSign Lite Client User Manual 3.2.3 Adjust Brightness Purpose: You can adjust the brightness for one or more terminals. Auto-Brightness Select Auto-Brightness radio and select backlight value. Terminal will automatically adjust screen backlight according to environment. Backlight Select Backlight radio and drag the slider to adjust brightness value. 3.2.4 Adjust Volume Purpose: You can adjust the volume for one or more terminals.
FocSign Lite Client User Manual Step 5 Click Apply. 3.3.2 Configure Time Zone Purpose: Configure terminal time zone according to the actuality. Step 1 Go to Terminal Management. Step 2 Select the desired terminal and click Remote Settings. Step 3 Go to Terminal Operation > Time Zone Settings. Step 4 Select time zone. Step 5 Click Apply. 3.3.3 Configure Logo Purpose: Enable/disable the startup logo of terminals. Step 1 Go to Terminal Management.
FocSign Lite Client User Manual Figure 3-5 Configure Channel Parameters Step 4 Select a channel and click . Step 5 Enter network camera parameters. Step 6 Click Apply to link to the network camera. Step 7 Optionally, click / to link the network camera to the other channel. 3.4 Terminal Maintenance 3.4.1 Upgrade Purpose: You are recommended to upgrade the terminal with the help of professional technical support. Before you start Save the upgrade file in your computer local path.
FocSign Lite Client User Manual It takes 1 to 10 minutes to upgrade the terminal. Do not cut off power supply during upgrade. The terminal will restart after upgrade. 3.4.2 Security Purpose: To increase security, you are recommended to turn off SADP after server configuration. Operate the function with the help of professional technical support. Step 1 Go to Terminal Management. Step 2 Select the desired terminal and click Remote Settings. Step 3 Go to Security Settings.
FocSign Lite Client User Manual Figure 3-6 Edit Network Parameters Step 4 Edit network parameters. Step 5 Enter Terminal Password and click Confirm. 3.4.5 Reset Password Before you start Ensure the terminal and your computer are in the same network segment. Step 1 Go to Terminal Management. Step 2 Click on the lower-right corner to view online terminals. Step 3 Select the desired terminal and click Reset Password. Figure 3-7 Reset Password Step 4 Enter Password and Confirm Password.
FocSign Lite Client User Manual Step 5 Click Confirm. Step 6 Click Export to export terminal configuration file. Step 7 Click Import to import a configuration file. You are recommended to import configuration file with the help of professional technical support. 3.4.6 Restore Defaults Purpose: If the terminal is abnormal, you can restore it to default settings. Step 1 Go to Terminal Management. Step 2 Click Restore of Terminal Default Parameters. 3.4.
FocSign Lite Client User Manual Chapter 4 Program Management You can create and modify program, and release it to different terminals. 4.1 Create Program Purpose: Create and configure the program according to the terminal type. Customize the program layout. The layout is same to the final release effect. Step 1 Go to Control Panel > Create Program. Step 2 Configure program basic information. Figure 4-1 Program Basic Settings Step 3 Set page attributes in Area 3. For detailed steps, refer to 4.1.
FocSign Lite Client User Manual Figure 4-2 Program Basic Settings Step 2 Enter the information accordingly. Program Name: Customized to specify the program. Program Type: Choose the type according to the terminal type. Touchscreen program can realize touch-screen function only when it’s played on the touchscreen terminal. Canvas Size: Choose the size according to terminal type. It supports to be customized. 4.1.2 Manage Page Step 1 Edit Page Attributes.
FocSign Lite Client User Manual Play Duration: When Play Mode is Custom, you can set the play duration accordingly. (Unit: s) When Play Mode is Auto, you need to set the play times. If you enter N, the page plays N time(s). When Play Mode is Loop Play, the page plays in a continuous loop. Step 2 Optionally, click to add page. Up to 32 pages can be added. You can adjust the program order. Program will be played according to the page order. 4.1.
FocSign Lite Client User Manual Figure 4-4 Window List Add Empty Window You can drag pictures, videos, and other materials into an empty window, or directly add a picture window, a video window, etc. Step 1 Click and click the page to create an empty window. Step 2 Drag and scale the window or edit the attributes to set its position and size. Step 3 Drag the material into the window.
FocSign Lite Client User Manual Add Template Window There are several templates consisting of passenger flow, picture, network camera, and other materials. You can draw the desired material and then edit it. The edited programs are also allowed to be set as templates. Step 1 Click Template and draw the desired material to the page to create a template window. The template material cannot be relocated and scaled. Step 2 Optionally, edit the text and pictures in the template.
FocSign Lite Client User Manual Step 3 Drag the video to the canvas, and set the position and size. Step 4 Set the Play Mode. Material Time: Play the material for one entire time. Custom: Play the material for the time you set. Step 5 Optionally, check Close Auto to play the video in mute. For multiple video windows added to one page, only one video can be played in non-mute mode. Check Close Auto for the other windows. Add Audio Window Only one audio window can be added for one single page.
FocSign Lite Client User Manual Click and click the page to create an empty TXT window. You can edit the content in the window. Add APP Window Only 1 APP window can be added for one single page, and no other window can be added. Step 1 Select Application on the program editing interface. Step 2 Click to select the app to be added. Step 3 Drag the app to the canvas. Add Clock Window Only 1 clock window can be added for one single page. Step 1 Select Clock on the program editing interface.
FocSign Lite Client User Manual Add Stream Media Window Up to 4 stream media window can be added for one single page. Step 1 Select Stream Media on the program editing interface. Step 2 Click , enter name and URL, and click Confirm. Step 3 Drag the stream media to the canvas, adjust the size and position. Step 4 Set play duration on the right. Step 5 Optionally, check Close Audio to play it in mute. Add IPC Material Window Step 1 Select Network Camera on the program editing interface.
FocSign Lite Client User Manual Step 3 Set window type: Pop-up window: click the button to pop-up the window. Normal: You need to set the connect method in the Event Type. Step 4 Select event type and link: New Pop-up Window: click the button to pop-up a new window. New Page: click the button to open a new page. 4.1.4 Edit Page Click the buttons to edit the program.
FocSign Lite Client User Manual Figure 4-6 Add Schedule Step 2 Select Configuration Mode: Day, Week, Custom. Custom mode supports to play the program on specific period. Up to 90-day custom schedule is supported. Step 3 Select Time Interval. Step 4 Select program in Program List, and drag in the schedule. Step 5 Set the start time and end time. Step 6 Click Release to enter the release interface. 4.2.2 Create Loop Schedule Step 1 Go to Control Panel > Create Schedule.
FocSign Lite Client User Manual 4.3 Release Purpose: Release the programs to information release screen. 4.3.1 Release Program Before you start: User has finished the program creating process. Step 1 Open Release interface. Click Quick Release on the program editing interface; Click Release on the creating schedule interface; Click on the play list interface. Step 2 Enter Task Name. Figure 4-7 Release Task Step 3 Select Applicable Terminal. Step 4 Select Effective Time.
FocSign Lite Client User Manual Step 5 Click Release. 4.3.2 Cut-in Release Purpose: The program or text will be played once the terminal received cut-in release order. Cut-in Program Release Step 1 Create Cut-in Release task. Click Cut-in Program on the program editing interface; Click on the play list interface. Step 2 Enter the release task name. Figure 4-8 Cut-in Release Task Step 3 Select Applicable Terminal. Step 4 Select Time Duration. Step 5 Click Release.
FocSign Lite Client User Manual Step 3 Select Applicable Terminal. Step 4 Click to Add Content, fill the text messages. Up to 5 messages can be added. Step 5 Select Time. Step 6 Set the window position, font, background, display mode, etc. Step 7 Optionally, click Preview to check the message play effect. Step 8 Click Release. 4.3.3 Release Default Video Purpose: You can set program as default video and release it to the terminal.
FocSign Lite Client User Manual Chapter 5 System Management Go to the upper-right corner of the client to set the saving path and system language, change password, or get more help. 5.1 Space Management Designate a saving path for the uploaded materials, and check storage space of the current saving path. Step 1 Click on the right side of the homepage to enter Space Management. Step 2 Optionally, view the current space usage. Step 3 Click Set to set the desired saving path for materials.
FocSign Lite Client User Manual Download the user manual. Check the open source software license. Check software version. Set the desired system language.
FocSign Lite Client User Manual UD20560B-A 0
