Network Video Recorder Quick Start Guide
Network Video Recorder Quick Start Guide TABLE OF CONTENTS Chapter1 Panels Description ............................................................................................ 7 1.1 Front Panel ................................................................................................................... 7 1.1.1 DS-9600NI Series ................................................................................................. 7 1.1.2 DS-7700NI Series .................................................
Network Video Recorder Quick Start Guide Quick Start Guide COPYRIGHT © 2016 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Video Recorder Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Network Video Recorder Quick Start Guide This manual is applicable to the models listed in the following table.
Network Video Recorder Quick Start Guide Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Provides additional information to emphasize or supplement important points of the main text. Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Network Video Recorder Quick Start Guide Safety Instructions Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
Network Video Recorder Quick Start Guide Chapter1 Panels Description 1.1 Front Panel 1.1.
Network Video Recorder Quick Start Guide Table 1-1 Panel Description No. Name Function Description ALARM Turns red when a sensor alarm is detected. READY Turns blue when the device is functioning properly. Turns blue when device is controlled by an IR remote. STATUS 1 Status Indicators Turns red when controlled by a keyboard and purple when IR remote and keyboard is used at the same time. HDD Flickers red when data is being read from or written to HDD. MODEM Reserved for future usage.
Network Video Recorder Quick Start Guide No. Name Function Description 6 Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). USB Interfaces Returns to the previous menu. ESC Presses for arming/disarming the device in live view mode. Enters the Manual Record settings menu. REC/SHOT Presses this button followed by a numeric button to call a PTZ preset in PTZ control settings. Turns audio on/off in the playback mode.
Network Video Recorder Quick Start Guide No. Name Function Description Turns on/off PTZ light (if applicable) in PTZ control mode. Switches between play and reverse play in playback mode. Cycles through tab pages. F2/ AUX Switches between channels in synchronous playback mode. Returns to the Main menu (after successful login). MENU/WIPER Presses and holds the button for five seconds to turn off audible key beep. Starts wiper (if applicable) in PTZ control mode.
Network Video Recorder Quick Start Guide No. Name Function Description Plays or pauses the video playing in playback mode. Advances the video by a single frame in single-frame playback mode. Stops/starts auto switch in auto-switch mode. Moves the active selection up and down in a menu. 9 JOG SHUTTLE Control Cycles through different channels in live view mode. Jumps 30s forward/backward in video files in the playback mode. Controls the movement of the PTZ camera in PTZ control mode.
Network Video Recorder Quick Start Guide Table 1-2 Panel Description No. Name Function Description POWER 1 Status HDD Indicators Tx/Rx Turns green when NVR is powered up. Blinks red when HDD is reading/writing. Blinks green when network connection is functioning normally. The Enter button is used to confirm selection in menu mode; or used to check checkbox fields and ON/OFF switch. In playback mode, it can be used to play or pause the video.
Network Video Recorder Quick Start Guide 1.1.3 DS-7600NI Series Figure 1-4 DS-7600NI Series Table 1-3 Panel Description No. Name Connections 1 POWER Turns green when NVR is powered up. 2 HDD Flickers red when data is being read from or written to HDD. 3 Tx/Rx Flickers blue when network connection is functioning properly. 4 USB Interface Universal Serial Bus (USB) port for additional devices such as USB mouse and USB Hard Disk Drive (HDD). 1.2 Rear Panel 1.2.
Network Video Recorder Quick Start Guide Figure 1-6 DS-9600NI-I16 Series Table 1-4 Panel Description No. Name Description 1 LAN1/LAN2 Interface 2 RJ-45 10/100/1000 Mbps self-adaptive Ethernet interfaces provided. 2 LINE IN RCA connector for audio input. 3 AUDIO OUT 2 RCA connectors for audio output. 4 HDMI1/HDMI2 HDMI video output connector. 5 VGA1/VGA2 DB9 connector for VGA output. Display local video output and menu. 6 USB 3.
Network Video Recorder Quick Start Guide 1.2.2 DS-7700NI Series Figure 1-7 DS-7700NI-I4 and DS-7700NI-K4 Series Figure 1-8 DS-7700NI-I4/16P and DS-7700NI-K4/16P Series The DS-7708NI-I4/8P and DS-7708NI-K4/8P provides 8 network Interfaces with PoE function. Table 1-5 Panel Description No. Name Description 1 LAN Interface 1 network interface provided for DS-7700NI-I4/P and DS-7700NI-K4/P, and 2 network interfaces for DS-7700NI-I4 and DS-7700NI-K4. 2 AUDIO OUT RCA connector for audio output.
Network Video Recorder Quick Start Guide ALARM OUT Connector for alarm output. 10 GROUND Ground (needs to be connected when NVR starts up). 11 AC 100V ~ 240V 100V to 240VAC power supply. 12 Power Switch Switch for turning on/off the device. 13 Network Interfaces with PoE function (supported by DS-7700NI-I4/P and DS-7700NI-K4/P) Network interfaces for the cameras and to provide power over Ethernet. 1.2.
Network Video Recorder Quick Start Guide output and menu. 4 HDMI Interface HDMI video output connector. 5 ALARM IN Connector for alarm input. ALARM OUT Connector for alarm output. 6 LAN Interface Network 1 10/100/1000 interface 7 USB Interface Universal Serial Bus (USB 3.0) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). 8 Ground Ground (needs to be connected when NVR starts up).
Network Video Recorder Quick Start Guide DS-7600NI-K1 and DS-7600NI-K1/4P Figure 1-12 DS-7600NI-K1 Series Figure 1-13 DS-7604NI-K1/4P Series Table 1-6 Panel Description Table 1-7 No. Table 1-8 Name Table 1-9 Description 1 Network Interfaces Network interfaces for the cameras and to with PoE function provide power over Ethernet. 2 Audio In RCA connector for audio input. 3 Audio Out RCA connector for audio output. 4 VGA Interface DB9 connector for VGA output.
Network Video Recorder Quick Start Guide Chapter 2 Installation and Connections 2.1 Installation During installation of the NVR: Use brackets for rack mounting. Ensure ample room for audio and video cables. When routing cables, ensure that the bend radius of the cables are no less than five times than its diameter. Connect the alarm cable. Allow at least 2cm (≈0.75-inch) of space between racks mounted devices. Ensure the NVR is grounded.
Network Video Recorder Quick Start Guide Step 2 Insert the key and turn in clockwise direction to open the panel lock. Figure 2-2 Insert Panel Key Step 3 Press the buttons on the panel of two sides and open the front panel. Figure 2-3 Open Panel Lock Step 4 Insert the hard disk along the slot until it is placed into position. Figure 2-4 Insert Hard Disk Step 5 Repeat the above steps to install other hard disks onto the NVR.
Network Video Recorder Quick Start Guide Figure 2-5 Lock Panel 2.2.2 Other Models Purpose: The following section introduces the HDD installation for the DS-7600NI and DS-7700NI series NVR. Take the example of DS-7600NI to describe installation steps. Step 1 Remove the cover from the NVR by unfastening the screws on the rear and side panel. Figure 2-6 Remove Cover Step 2 Connect one end of the data cable to the motherboard of NVR and the other end to the HDD.
Network Video Recorder Quick Start Guide Figure 2-8 Connect Power Cable Step 4 Place the HDD on the bottom of the device and then fasten the screws on the bottom to fix the HDD.
Network Video Recorder Quick Start Guide 2.3 Connections 2.3.1 Alarm Input Wiring The alarm input is an open/closed relay. To connect the alarm input to the device, use the following diagram. If the alarm input is not an open/close relay, please connect an external relay between the alarm input and the device. Figure 2-10 Alarm Input Wiring 2.3.
Network Video Recorder Quick Start Guide If you connect an AC load to the alarm output 3 of the NVR, then you must remove the JP 3 jumper. 2.3.3 Alarm Connection To connect alarm devices to the NVR: Step 1 Disconnect pluggable block from the ALARM IN /ALARM OUT terminal block. Step 2 Unfasten stop screws from the pluggable block, insert signal cables into slots and fasten stop screws. Ensure signal cables are tight. Step 3 Connect pluggable block back into terminal block. 2.3.
Network Video Recorder Quick Start Guide 2.4 HDD Storage Calculation Chart The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate. Bit Rate Storage Used 96K 42M 128K 56M 160K 70M 192K 84M 224K 98M 256K 112M 320K 140M 384K 168M 448K 196M 512K 225M 640K 281M 768K 337M 896K 393M 1024K 450M 1280K 562M 1536K 675M 1792K 787M 2048K 900M 4096K 1.8G 8192K 3.6G 16384K 7.
Network Video Recorder Quick Start Guide Chapter 3 Menu Operation 3.1 Start up Your Device Proper startup and shutdown procedures are crucial to expanding the life of the NVR. To start your device: Step 1 Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an Uninterruptible Power Supply (UPS) be used in conjunction with the device. The Power button on the front panel should be red, indicating the device is receiving the power.
Network Video Recorder Quick Start Guide We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
Network Video Recorder Quick Start Guide Connect at least 4 dots to draw the pattern. Each dot can be connected for once only. Step 3 Draw the same pattern again to confirm it. When the two patterns match, the pattern is configured successfully. If the two patterns are different, you must set the pattern again. 3.4 Login to the System Purpose: If the device has logged out, you must log in the device before operating the menu and other functions.
Network Video Recorder Quick Start Guide 3.5 Enter Wizard to Configure Quick Basic Settings The Setup Wizard can walk you through some important settings of the device. By default, the Setup Wizard starts once the device has loaded. Check the checkbox to enable Setup Wizard when device starts. Click Next to continue the setup wizard. Follow the guide of the Setup Wizard to configure the system resolution, system date/time, network settings, HDD management, record settings, etc. Figure 3-4 Wizard 3.
Network Video Recorder Quick Start Guide Figure 3-5 Network Settings Step 2 Select the General tab. Step 3 In the General Settings interface, you can configure the following settings: NIC Type, IPv4 Address, IPv4 Gateway, MTU and DNS Server. Step 4 If the DHCP server is available, you can check the checkbox of DHCP to automatically obtain an IP address and other network settings from that server. Step 5 After having configured the general settings, click the Apply button to save the settings. 3.
Network Video Recorder Quick Start Guide Figure 3-6 Add IP Camera Step 3 Enter IP address, protocol, management port, and other information of the IP camera to add. Step 4 Enter the login user name and password of the IP camera. Step 5 Click Add to finish the adding of the IP camera. Step 6 (Optional) Click Continue to Add to continue to add other IP cameras. 3.8 Start Live View Enter the live view mode ( ).
Network Video Recorder Quick Start Guide The device supports the RAID storage function. Through one-touch configuration, you can quickly create the disk array. By default, the array type to be created is RAID 5. Before you start: Enable RAID function. Install at least 3 HDDs. If more than 10 HDDs are installed, 2 arrays will be created. To maintain reliable and stable running of the HDDs, it is recommended to use enterprise-level HDDs with the same model and capacity.
Network Video Recorder Quick Start Guide Option 2: Step 1 Go to Storage > Recording Schedule. Step 2 Select a camera. Step 3 Check the Enable Schedule. Step 4 Select a Record Type. The record type can be Continuous, Motion Detection, Alarm, Motion | Alarm, Motion & Alarm, Event, etc. Figure 3-8 Record Schedule Step 5 Select a day and click-and-drag the mouse on the time bar to set the record schedule. Step 6 Click Apply to save the settings. 3.
Network Video Recorder Quick Start Guide Step 3 You can use the toolbar in the bottom part of Playback interface to control playing progress.
Network Video Recorder Quick Start Guide Chapter 4 Access by Web Browser You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. Purpose: You can get access to the device via web browser.
Network Video Recorder Quick Start Guide If the device is already activated, enter the user name and password in the login interface, and click the Login button. Figure 4-2 Login Step 3 Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in.
Network Video Recorder Quick Start Guide UD07889B 37 UD07355B
