User's Manual
Table Of Contents
- 1. REGULATORY AND SAFETY INFORMATION
- 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ
- 3. CLEANING
- 4. BATTERIES
- 5. INTRODUCTION
- 6. OPTIONS AND ACCESSORIES
- 7. EDACS, CONVENTIONAL, AND P25 OPERATION
- 7.1 TURNING ON THE RADIO
- 7.2 CONTROLS
- 7.3 DISPLAY
- 7.4 TRI-COLOR LED
- 7.5 RADIO STATUS MESSAGES
- 7.6 ERROR MESSAGES
- 7.7 ALERT TONES
- 7.8 VOICE ANNUNCIATION
- 7.9 SYSTEM/ZONE SELECTION
- 7.10 GROUP/CHANNEL SELECTION
- 7.11 MODIFY SCAN LIST
- 7.12 MENU
- 7.13 BLUETOOTH
- 7.14 BACKLIGHT ADJUST
- 7.15 CONTRAST ADJUST
- 7.16 DECLARE AN EMERGENCY
- 7.17 LOCKING/UNLOCKING KEYPAD
- 7.18 HIGH/LOW POWER ADJUSTMENT
- 7.19 ENCRYPTION
- 7.20 SCAN OPERATION
- 7.21 SCANNING TRUNKED SYSTEMS
- 7.22 EMERGENCY OPERATION
- 7.23 MIXED SYSTEM ZONES
- 7.24 CALLER ID
- 7.25 STEALTH MODE
- 7.26 INDIVIDUAL CALLS
- 7.27 TELEPHONE INTERCONNECT CALLS
- 7.28 PRE-STORING INDIVIDUAL AND TELEPHONE INTERCONNECT CALLS FROM THE KEYPAD
- 7.29 STATUS/MESSAGE OPERATION
- 7.30 DYNAMIC REGROUP OPERATION (EDACS)
- 7.31 MACRO KEY OPERATION
- 7.32 DATA COMMUNICATIONS
- 7.33 SELECTIVE SIGNALING (CONVENTIONAL)
- 7.34 RADIO TEXTLINK OPERATION
- 7.35 VIEW GPS INFORMATION
- 8. OPENSKY OPERATION
- 8.1 CONTROLS
- 8.2 TRI-COLOR LED
- 8.3 LOGIN TO THE NETWORK
- 8.4 LOG OFF THE NETWORK
- 8.5 PERSONALITY
- 8.6 OPENSKY DISPLAY OVERVIEW
- 8.7 ALERT TONES
- 8.8 BASIC MENU STRUCTURE
- 8.9 BLUETOOTH
- 8.10 ERROR MESSAGES
- 8.11 KEYPAD FUNCTION COMMANDS (SYSTEM MODEL ONLY)
- 8.12 QUICK KEYS (SYSTEM MODEL ONLY)
- 8.13 LOCK/UNLOCK THE KEYPAD
- 8.14 DUAL-TONE MULTI-FREQUENCY (SYSTEM MODEL ONLY)
- 8.15 CHANGING THE ACTIVE PROFILE
- 8.16 CHANGING THE SELECTED TALK GROUP
- 8.17 ADJUSTING DISPLAY AND BUTTON BACKLIGHT BRIGHTNESS
- 8.18 STEALTH MODE
- 8.19 ADJUSTING SIDE TONE AUDIO LEVEL
- 8.20 CHANGE OPERATING MODE
- 8.21 RECEIVING AND TRANSMITTING VOICE CALLS
- 8.22 ADJUSTING AUDIO TREBLE LEVEL
- 8.23 TALK GROUP LOCK OUT
- 8.24 SCANNING
- 8.25 MAKING SELECTIVE CALLS
- 8.26 SELECTIVE ALERTS
- 8.27 MAKING INTERCONNECT CALLS (SYSTEM MODEL ONLY)
- 8.28 EMERGENCY COMMUNICATIONS
- 8.29 OPENSKY ENCRYPTION
- 8.30 STATUS MESSAGES
- 8.31 REQUEST TO TALK (RTT) MESSAGES
- 8.32 SITE LOCK
- 8.33 GPS COORDINATES
- 8.34 V-TAC OPERATION
- 9. MARITIME FREQUENCIES
- 10. BASIC TROUBLESHOOTING
- 11. CUSTOMER SERVICE
- 12. WARRANTY
- APPENDIX A - CONFIGURING ENCRYPTION
14221-1500-2000, Rev. K
68
NAME
TONE
DESCRIPTION
Emergency Cleared Tone Single long low-pitched tone Sounds when an emergency is cleared.
Selective Call Ring Tone
A ringing tone similar to a
telephone
Ringing is repeated every four (4) seconds until the call is
accepted or rejected by the radio being called or until the
network drops the call if unanswered after one minute.
Roam Tone
Two short tones, one high-
pitched and one low-pitched
Sounds when the radio transitions from one radio base station
site to another. While transmitting voice.
Out of Range Tone Three brief tones
If enabled via programming, sounds at a programmable interval
while the radio is in a state of persistent deactivation.
Priority Bump
Single medium mid-pitched
tone.
Sounds when the current received call is preempted by a
higher priority call.
XCOV Connect Tone
or
Site Found Tone
Three short high-pitched tones.
Sounds when a radio connects to a V-TAC in XCOV, XCOV-
TG, or XCOV-Prof mode.
Sounds when the selected site is found using the Site Lock
Menu.
XCOV Disconnect Tone
or
Site Not Found Tone
Three short high-pitched tones.
Sounds when a radio connects to a V-TAC in XCOV, XCOV-
TG, or XCOV-Prof mode.
Sounds when the selected site is not found using the Site Lock
Menu.
Man Down Tone
Single long low-pitch tone
followed by a single short high-
pitched tone.
Sounds when the man down accessory is connected to the
radio’s UDC port and the radio is a horizontal