Operation Manual

Learning Codes
In addition to using codes from the remote’s
internal code library, the AVR 8000’s remote is
able to “learn”codes from remotes that may
not be in the code library. In addition, you may
use this function to “learn over” the codes
from a preprogrammed device to add functions
not included in the preprogrammed codes. To
learn or transfer codes from an IR remote to
the AVR 8000’s remote, follow these steps:
1. Place the front of the original remote with
the code being sent so that it is facing the
IR Transmitter Window b on the
AVR 8000 remote “head-to-head.” The
remotes should be between one and three
inches apart.
2. Select the button on the remote that you
wish to use as the device selector for the
codes about to be entered. This may be any
of the
Input Selectors e.
3. Press the
Input Selector e button
chosen and the
Learn Button at the
same time. Hold these buttons until the
Program/SPL Indicator c flashes amber
and the light under the device selector but-
ton turns red. Release the buttons.
4. Press the button on the AVR 8000 remote
that you wish to program. Note that the
Program/SPL Indicator c will stop
flashing.
5. Within five seconds, press and hold the but-
ton on the original remote that you wish to
“teach” into the AVR 8000 remote. When
the
Program/SPL Indicator c turns
green three times, release the button. Note
that the Program Indicator will then begin to
flash amber again.
NOTE: If the Program/SPL Indicator c
turns red during Step 4 or 5, the program-
ming was not successful. Repeat the steps to
see if the code will “take.”
6. Repeat Steps 4 and 5 for each button on the
source remote that you wish to transfer to
the AVR 8000 remote.
7. Once all codes have been transferred from
the original source remote to the AVR 8000
remote, press the
Learn Button .
8. Repeat Steps 1 through 7 for any additional
remotes you wish to “teach” into the
AVR 8000 Remote.
Erasing Learned Codes
The AVR 8000’s remote allows you to remove or
erase the code learned into a single button for a
single device, to remove or erase the code set for
all the codes that have been programmed into
specific device buttons, or to erase all commands
that have been learned to all devices.
To erase a single learned code from within a sin-
gle device’s settings, follow these steps:
1. Press and hold both the
Input Selector e
within which the individual button to be
erased has been programmed and the
Learn
Button
.
2. When the red LED under the
Input Selector
turns red and the Program/SPL Indicator
c flashes amber, release the buttons.
3. Press and release the
Input Selector e
again for the device within which the
individual button to be erased has been
programmed.
4. Press the
7 Button r four times.
5. Press and release the individual button for
which the code is to be erased.The
Program/SPL Indicator c will blink
green two times and then return to amber.
6. To erase other buttons within the same
device, press them as noted in Step 5.
7. When all buttons to be erased have been
pressed, press the
Learn Button to
complete the process.
To erase all codes within a single device, follow
these steps:
1. Press and hold both the
Input Selector e
for which you wish to erase the codes and the
Learn Button .
2. When the red LED under the
Input Selector
turns red and the Program/SPL Indicator
c flashes amber, release the buttons.
3. Press and release the
Input Selector e
again for the device whose codes you wish
to erase.
4. Press the
8 Button r four times.
5. The
Program/SPL Indicator c will turn
off and the red light under the
Input
Selector
will flash on and off once to indi-
cate that the codes have been erased.
To erase all codes that have been programmed
to all devices in the remote, follow these steps:
1. Press any
Input Selector e for which you
wish to erase the codes and also the
Learn
Button
.
2. When the red LED under the
Input Selector
turns red and the Program/SPL Indicator
c flashes amber, release the buttons.
3. Press and release the same
Input Selector
e again for the device whose codes you
wish to erase.
4. Press the
9 Button r four times.
5. The
Program/SPL Indicator c will
turn off and the red light under the
Input
Selector
e will flash on and off once to
indicate that the codes have been erased.
Macro Programming
Macros enable you to easily repeat frequently
used combinations of commands with the press
of a single button on the AVR 8000’s remote
control. Once programmed, a macro will send
out up to 19 different remote codes in a prede-
termined sequential order enabling you to auto-
mate the process of turning on your system,
changing devices, or other common tasks. The
AVR 8000’s remote can store up to five sepa-
rate macro command sequences: one that is
associated with the
Power On Button d
and four more that are accessed by pressing the
Macro Buttons .
1. Press the
Mute Button and the
Macro Button to be programmed
or the
Power On Button d at the same
time. Note that the
AVR Selector f
will light red, and the Program/SPL
Indicator
c will flash amber.
2. Enter the steps for the macro sequence by
pressing the button for the actual command
step. Although the macro may contain up to
19 steps, each button press, including those
used to change devices, counts as a step.
The
Program/SPL Indicator c will flash
green to confirm each button press as you
enter commands.
33
46
33
44
44
44
44
44
44
40 PROGRAMMING THE REMOTE
Programming the Remote