Product manual

ManualsBrandsHarbor Freight Tools ManualsPaintHarbor Freight Tools 1 Gal Air Paint Shaker

PNEUMATIC PAINT SHAKER

Model

94605

ASSEMBLY AND OPERATION INSTRUCTIONS

Due to continuing improvements, actual product may differ slightly from the product described

herein.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

this manual or any artwork contained herein may be reproduced in any shape

or form without the express written consent of Harbor Freight Tools.

For technical questions or replacement parts, please call 1-800-444-3353.

Revised 07g

Summary of content (10 pages)

PAGE 1
PNEUMATIC PAINT SHAKER Model 94605 Assembly and operation instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright © 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
PAGE 2
Specifications Item Description Function Shakes and mixes paint in cans from one gallon to one quart. Air Pressure Requirement 40 to 70 PSI Air Consumption 3.2 CFM at 70 PSI Can Jaws 3 to 11 inch adjustable, non-marring jaws Speed 700 CPM (free speed - no load) Air Inlet Size 1/4” - 18 NPT (female threads) Air Hose 3/8 (ID) inch (recommended) Load Capacity 11 lbs. (maximum) Overall Dimensions 16-3/4 (L) x 9-1/8” (W) x 12-3/4 (H) inches Weight 21.12 lbs.
PAGE 3
5. Use the right tool for the job. Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. There are certain applications for which this tool was designed. It will do the job better and more safely at the rate for which it was intended. Do not modify this tool and do not use this tool for a purpose for which it was not intended. 6. Use eye protection. Always wear ANSI approved impact safety goggles when using the Paint Shaker. 7. Dress properly.
PAGE 4
15. Do not operate tool if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 16. Make sure the place where you use this product is properly ventilated. 17. The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm).
PAGE 5
3. Move the Paint Shaker aside, and drill holes using a drill matching the size of the Base (1) mounting holes. 4. Mount Paint Shaker to the workbench using supplied nuts and bolts hardware. If the supplied hardware will not accommodate the workbench, other hardware will need to be purchased. Air Connection 1. Wrap a small amount of Teflon® joint tape (not supplied) around the treads of the Control Valve (6), then screw it into the Inlet Fitting (7) until secure. Do not overtighten.
PAGE 6
Operation Warning: Verify that the paint containers are securely closed before shaking, to avoid spilling or property damage. Make sure there is oil in Oiler (52) BEFORE use. See page 6. 1. Place the paint can within the Jaws (48) and securely tighten Handle (38). 2. Verify that the Control Valve (6) is in the Off position (handle perpendicular to air flow direction) as shown on page 4. 3. Turn on the air pressure at the air supply tank or compressor.
PAGE 7
Maintenance 1. After each use, remove the air hose and wipe the tool with a clean cloth to remove any dirt and grease buildup. 2. To maintain tool life, always lubricate the air line by adding a few drops of pneumatic tool oil to the air line before each use. Or, install the automatic oiler-filter system as previously illustrated. 3. Before each use, drain water out of the air compressor tank and condensation from the air lines. Refer to the Air Compressor Operator’s Manual.
PAGE 8
Parts list Part QTY Part 1 Base Description 1 28 Crank Pin Description QTY 1 2 Nut 2 29 Main Shaft 1 3 Screw 1 30 L-Connecting 1 4 Rubber defends & rises cushion 2 31 Ferrule 2 32 Weave Pipe 1 5 Rubber Cushion 2 33 Screw 2 6 Control Valve 1 34 Spring Pad 2 7 Air Inlet Fitting 1 35 Screw 1 8 Valve Body Screw 3 36 Rocker Handle 1 9 Lower Valve Body 1 37 Nut 1 10 Packing 1 38 Handle 1 11 Valve Piece 1 39 Thrust Washer 1 12 Screw 1 40
PAGE 9
Assembly Drawing SKU 94605 For technical questions, please call 1-800-444-3353.
PAGE 10
90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.