Hanover Outdoor Furniture IMPORTANT If you have any problems with this product (missing or damaged parts, assembly issues, etc.), PLEASE DO NOT RETURN TO THE RETAILER/STORE from where you purchased the product. Please call our Toll‐Free Customer Service Hotline at: 1‐800‐416‐3511 Between 9:00 AM and 5:00 PM Eastern Time, Monday through Friday Or visit our website at: www.hanover‐products.
Outdoor Furniture 1-Year Limited Warranty Program For a period of one (1) year after purchase, the Manufacturer will either repair or replace defective components in accordance with this Limited Warranty. This warranty is between Manufacturer and the original purchaser and is valid only when accompanied by the original purchaser’s sales receipt showing original date of purchase and location of purchase. Replacements under this warranty revert back to the date of original purchase for future warranty.
Care & Maintenance Outdoor furniture can be enjoyed for many years when well maintained. Regular Maintenance Wash the furniture with a solution of mild detergent and water, rinse with clear water, and dry thoroughly. To all metal frames, apply a fine, clear automobile wax for maximum protection against harmful ultraviolet exposure and salt air. For best protection, perform this maintenance two or three times per year in low pollution areas or more frequently in high pollution areas.
ASSEMBLY INSTRUCTIONS CSA Model 98900 ARV08200 Installer: Leave these instructions with consumer. Consumer: Keep these instructions for future reference. DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department. WARNING: Improper installation, adjustment alteration, service or maintenance can cause injury or property damage.
TABLE OF CONTENTS Important Safety Information 3 Important About Propane 4 Specifications 4 Parts Identification List 5 Installation 6-7 Natural Gas Conversion 8 Batteries 9 Maintenance 9 Lighting Instructions 10 Troubleshooting Guide 11 Warranty 12 2
IMPORTANT SAFETY INFORMATION The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54; International Fuel Gas Code. ; Natural Gas and Propane Installation Code, CSA B149.1; or Propane Storage and Handling Code, B149.2, as applicable. The appliance and its appliance main gas valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5kPa).
IMPORTANT SAFETY INFORMATION ABOUT PROPANE (LP) GAS A self contained LP-gas cylinder for use with this appliance must have a capacity of 20 lbs. and must be equipped with a Type 1 connector and an OPD (overfill protection device). See Figure 1. The LP-gas supply cylinder to be used must be constructed and marked in accordance with the specification for LP-gas cylinders of the U.S.
PARTS IDENTIFICATION LIST PART DESCRIPTION PART# QTY A CONTROL KNOB FP1245 1 B GAS VALVE FP0307 1 C THERMOCOUPLE FP0004 1 D LP REGULATOR HOSE FP1329 1 E ELECTRODE FP1330 1 F ORIFICE ELBOW FP0310 1 G IGNITION MODULE FP0006 1 H PROPANE ORIFICE FP1283 1 I NATURAL GAS ORIFICE FP1284 1 J “AAA” BATTERY(1.5V) HW0705 1 K FIRE ICE FP1592 1 L FOOTCAP FC0553 4 M 1/4" X 20 MM BOLT HW0036 4 N Ø20 X Ø6.5 X 2.
INSTALLATION 1. Identify parts packed in carton against the parts list. Remove all protective materials and set parts on a flat, non-abrasive surface. 2. With the help of another person, carefully place the table top onto the table base. After making any necessary adjustments to the alignment of the table top and the assembled base, use four bolts and washers as shown in Figure 3. Guide the bolts through the holes in the base brackets, into the pre-drilled holes in the table top. Do not tighten completely.
4. Tighten the threaded knobs found on the tank tray (Figure. 5) so that the LP tank cannot move from side to side. Do not remove plastic cap from end of threaded section. Figure 5 5. After making any necessary adjustments to the parts, use the hex bolt driver to tighten all bolts. Note: each bolt must be tightened a few revolutions at a time. Repeat until all bolts are tight. Do not over tighten. Over tightening may strip bolts. Cover all bolts with covers. 6.
NATURAL GAS CONVERSION Natural gas conversion must be performed only by your natural gas provider or service company. Step 1- At the control panel, disconnect the rubber gas hose from the gas valve. Step 2- Below the burner, disconnect the aluminum gas tube from the orifice elbow. Step 3- Remove the 2 M4 nuts from the orifice holder and remove the orifice bracket assembly. Step 4- Disconnect the orifice from the elbow and replace it with the Natural Gas orifice from the kit.
Step 5- Stick the conversion label on the rating plate as shown in Figure 9 Metal Rating Plate Serial Number _________________ Model Number: 98900 1. must be used. This regulator is set for an outlet pressure of CAUTION: The gas pressure regulator provided with this appliance 2. This appliance has been converted to use Natural Gas. 3. Input 40,000 Btu/hr. Max Gas Supply Pressure 7 inch w.c. (1.74 kPa) Min. 4. Gas Supply Pressure 5 inch w.c. (1.24 kPa) 5.in.609 mm. Top 72 in. 1828 mm.
LIGHTING INSTRUCTIONS 1. Locate the control and igniter panel. Make sure the control knob is in the “OFF” position. See Figure 12.Open the tank door and open the tank valve all the way. 2. Push in the igniter button. You will hear a slight clicking sound. With the igniter button pushed in, push and turn the control knob to the “ON” position. The fire should light within a few seconds. Once the flame is lit, release the igniter button and continue to hold the control knob in for 10 to 15 seconds.
TROUBLESHOOTING GUIDE PROBLEM CAUSE REMEDY No Propane Gas at Burner Burner won’t light No Spark at Electrode Lack of oxygen Thermocouple not in flame Burner won’t stay lit after lighting Check that gas tank valve is open. Turn control knob to “ON” and push control knob in. Make sure tank has propane gas. Check that AAA battery is installed with negative (-) end first and has a charge. Check that the wire is connected to the ignition module. Check that the electrode is not cracked or broken.
ONE-YEAR LIMITED WARRANTY What is Covered Under This Warranty? The item you have purchased is warranted against defects in material and workmanship for the following parts from the date of purchase for the period of warranty as outlined below, but only when the unit is installed and operated in accordance with the instructions in this Owner’s Manual and in compliance with local building and fire codes: Limited 1 Year • Stainless Tube/Plate burner Limited 90 days • All remaining parts How Do I Obtain Warrant
