Installation and Operation Instructions ELECTRIC FIREPLACE F35WMEF
Important Safety Instructions 4-6 Listing Approvals 7 Product Dimensions 8 Locating Fireplace 9 Unpacking and Testing Fireplace 10 Grounding Instructions 10 Installation 11-12 Finishing Ckecklist 13 Operating Instructions 13-14 Replacing The Rock/Log Set 15 Troubleshooting 16
1. Prior to plugging your heater into an electrical outlet, verify that the house circuit breakers for the outlet are on. 2. The heater may emit a slight, harmless odor when first used. This odor is normal and it is caused by the initial heating of internal heater elements and will not occur again. 3. If your heater does not emit heat, consult the operation section of this manual for further information. 4. Use with a CSA or UL certified surge protector.
IMPORTANT SAFETY INSTRUCTIONS When using this electric fireplace, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Read all instructions before using this electric fireplace. 2. T his heater is hot when in use. To avoid bums, do not let bare skin touch hot surfaces. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.
IMPORTANT SAFETY INSTRUCTIONS 11. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage the heater. 12. To prevent possible fire, do not block air intakes in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. 13. The electric fireplace has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored. 14.
This heater has been tested in accordance with the CSA Standards.
Healll' Vents (Do Not Cover) TOP VIEW 35.0" 0 ,---------.. ID 17.r. 0 '---------_J 5.5" QI FRONT VIEW c ,. SIDE VIEW BOTTOM VIEW ..
LOCATING FIREPLACE .,4� WARNING: Due to high temperatures, this electric fireplace should be located out of traffic. Keep combustible materials such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9m) from the front of the heater. WARNING: Never locate this electric fireplace where it may fall into a bathtub or other water container. CAUTION: Do not expose the electric fireplace to the elements (such as rain, etc.
120
..4 � WARNING: RISK OF FIRE!The power cord must not be pinched or against a sharp edge. Secure cord to avoid tripping or snagging to reduce risk of fire, electric shock or personal injury. Do not run cord under carpeting. Do not cover cord with throw rugs, runner or the like. Arrange cord away from traffic area and where it will not be tripped over. ..4� WARNING: RISK OF FIRE!To prevent a possible fire,do not block air intake or exhaust in any manner.
3
FINISHING CHECKLIST > Power supply service must be completed prior to finishing to avoid reconstruction. > Heater vents and air openings cannot be covered in any circumstances. OPERATING INSTRUCTIONS Once the unit has been properly connected to a grounded electrical outlet, it is ready to operate. Note: Ensure the house circuit breakers for the power supply are turned on. Main Power Switch: The Main Power Switch is located on the right side of the unit. Figure 4 illustrates the location of the switch.
The manual controls are located on the left side of the fireplace. You have the following controls: 1. Power ON/OFF: Power to the unit 2. Flame brightness controls: Allows you to adjust the flame to suit your mood.Press increase flame brightness and to to decrease flame brightness.You must press the button Several times to see the full flame effect. 3. Low heat:700 watts 4. High heat: 1400 watts Please note: The heater touchpanel control must be touched 2 times to achieve high heat. 5.
Replacing The Rock/Log Set TO CHANGE LOG/ROCK SET (NOTE: MAKE SURE FIREPLACE IS TURNED OFF AND HAS BEEN UNPLUGGED FROM ELECTRICAL OUTLET BEFORE ATTEMPTING TO CHANGE THE LOG/ROCK SET): 1. Place fireplace on a flat, level surface (FIG 1). 2. Remove 3 screws located on each side of glass face of fireplace (FIG 2 and FIG 3). 3. Remove screws that attach the log/rock set to the front of fireplace (FIG 4). 4. Replace with the desired set（log/rock）and re-assemble new set by inserting and tightening screws(FIG 5). 5.
The remote takes 2 x AAA batteries
