Instruction Manual HI9060 HI9061 HI 91541 Portable Waterproof Microprocessor Thermistor Thermometers ins ru m en s °C HI 90 micro 60 therm compute r ome ter -50 .. -58 .. .. .. .. +1 50°C .. .. .. +302 °F CLE AR °C/°F ON/O FF HI LO HOL D http://www.hannainst.
Dear Customer, Thank you for choosing a Hanna Instruments Product. Please read this instruction manual carefully before using the instrument. This manual will provide you with all the necessary information for the correct use of the instrument, as well as a precise idea of its versatility in a wide range of applications. These instruments are in compliance with directives. TABLE OF CONTENTS Preliminary Examination ........................... 3 General Description ..................................
Each HI91541C or HI 91541F comes supplied complete with 4 batteries (1.5V, AA size). Several types of HI 764 temperature probes are available to meet all your requirements (see page 16). A series of HI764 calibration test plugs are also available to check the meter's accuracy (see page 13). HI9060 can measure in Centigrade and in Fahrenheit. Other features of HI 9060 include: display and clearing of the maximum / minimum temperature measured reading hold.
FUNCTIONAL DESCRIPTION HI 9061 FUNCTIONAL DESCRIPTION HI 91541 1 1 2 2 ins rum n s e e ins rum n s - 1.5V 3 + °C - 1.5V 1.5V - + 1.5V - 1.5V + - 1.5V + + 1.5V - + 1.5V - °C Foodcare Foodcare 1. Battery Cover 1. Battery Cover 3. LCD Display HI 9061 HI 91541 4. ON/OFF Key 4. ON/OFF Key Resolution ON/OFF MICROCOMPUTER THERMOMETER 2. Temperature Probe Connector 3. LCD Display Range RANGE -50.0°C to 300°C ACCURACY ±0.4°C ON/OFF 2.
OPERATIONAL GUIDE INITIAL PREPARATION Each meter is supplied complete with batteries. Remove the back cover, unwrap the batteries and install them while paying attention to their polarity. To switch on, press the ON/OFF key on the front of the unit. HI / LO MEMORIES (for HI 9060 only) The maximum and minimum temperatures are monitored throughout a continuous measuring process. The values may be recalled or cleared at any time during the measurement.
HOLD MODE (for HI 9060 only) The reading hold function is activated by the HOLD key. The measured temperature is frozen on the display when this function key is pressed. A blinking "M" on the display indicates the operating mode. HI 9060 and HI 9061 stop to operate when the low battery signal is detected. The user is warned by the code "Eb". HI 91541 displays "BAT" when the batteries are run down. °C M See also the Battery Replacement section on page 14.
DISPLAY CODES GUIDE Your thermometer is factory programmed to diagnose a fault or warn of low battery levels. This is indicated by the error codes on the LCD. Moreover, self-explanatory symbols are used to remind the user of the operating mode or conditions. DISPLAY Er (for HI9060 and HI 9061) ----(for HI 91541) Eb DESCRIPTION The probe is not connected to the instrument or the reading is out of range. Battery weak, need to be replaced.
BATTERY REPLACEMENT When the batteries become weak, the meter displays "Eb" (for HI9060 and HI9061) or "BAT" (for HI91541) to warn the user. BAT Battery replacement must only take place in a non hazardous area using the battery types specified in this instruction manual (see page 17). In order to replace rundown batteries, simply remove the two screws on the rear cover of the instrument and replace the four batteries with new ones paying attention to the correct polarity.
cable and green handle HI765PG/10Penetration probe with 10 m (33') cable and green handle HI765PR Penetration probe with 1 m (3.3') cable and red handle HI 765PR/10 Penetration probe with 10 m (33') cable and red handle HI 765PW Penetration probe with 1 m 3.3') cable and white handle HI 765PW/10Penetration probe with 10 m (33') cable and white handle HI 765W Wire probe, without handle (hardto-reachplaces) with 1 m(3.
WARRANTY CE DECLARATION OF CONFORMITY All Hanna Instruments meters are warranted for two years against defects in workmanship and materials when used for their intended purpose and maintained according to instructions. The probes and calibration keys are warranted for a period of six months. This warranty is limited to repair or replacement free of charge. Damages due to accident, misuse, tampering or lack of prescribed maintenance are not covered.
HANNA LITERATURE Hanna publishes a wide range of catalogs and handbooks for an equally wide range of applications. The reference literature currently covers areas such as: • Water Treatment • Process • Swimming Pools • Agriculture • Food • Laboratory • Thermometry and many others. New reference material is constantly being added to the library. h t t p : / / w w w . h a n n a i n s t .