Installation Guide

Étape 1:Inspection et préparation
Suivez les instructions des murs et des armoires de base pour inspecter les armoires et préparer et marquer les murs pour l'installation de
l'armoire. Installez toutes les armoires murales avant d'installer l'armoire d'angle SCB.
Étape 2 : Préparation du panneau aveugle
Localisez et retirez le panneau aveugle et le remplissage du dessous de l'armoire. Mettre le mastic
de côté pour une utilisation ultérieure. Coupez le panneau aveugle de manière à ce qu'il recouvre le
côté ouvert de l'armoire d'angle aveugle de 1/2" sur tous les (4) côtés de l'ouverture. Marquez (8)
emplacements des trous indiqués dans l'image à droite à ¼" des bords du store. Pré-percez les (8)
emplacements marqués avec un foret de 3/32" de diamètre.
Étape 3 : Installation du panneau aveugle
Sur le côté de l'ouverture du coin carré du cadre de façade (ouverture sans la porte xée),
marquez des lignes sur le cadre de façade à ½" du bord de l'ouverture de la porte. Cela
localisera le panneau aveugle pour la xation. Placez le panneau aveugle pré-percé sur le
cadre de façade et marquez les emplacements des trous pré-percés du panneau aveugle
sur le cadre de façade. Retirez le panneau aveugle et pré-percez le cadre de façade avec
un foret de 3/32" de diamètre à tous les (8) emplacements, à ½" de profondeur. Fixez le
panneau aveugle au cadre de façade à l'aide de (8) vis à tête plate n° 6 x ½".
REMARQUE: La porte peut être placée de chaque côté de l’armoire selon les besoins de conception.
REMARQUE: Pour
déterminer le revêtement de
votre armoire, référez-vous à
l'image de gauche montrant la
couverture avant de la porte
et du tiroir du cadre avant.
(6.18.13) SCB INSTRUCTIONS A5131
STEP 2
STEP 3
STEP 4
The blind panel will need to be trimmed to size to fit
over the opening of your square corner base cabinet.
Then the blind panel will need to be drilled for
installation. Mark the (8) hole locations shown to the
right on the blind panel. All holes should be located
1/4" from edges of blind panel. Drill the (8)
premarked locations with a 7/64" diameter drill bit
through the panel.
*Panel is located under cabinet with Filler Board
Locate the studs with a stud finder and mark where
the cabinets are to be installed. Remove all the doors
and drawers from the cabinets before installation.
Measure the area to confirm that the kitchen design
used will work.
Remove door and drawer from square corner
cabinet. On the square corner opening side
of the face frame (opening without door
attached), a line 1/2” from the edge of the
opening needs to be marked onto the face
frame. This will locate the blind panel for
attachment.
NOTE: Door can be placed on either side of
the cabinet depending on design needs.
DOOR LOCATION
FACE FRAME
1/2
1/2
1/2
1/2
Informations sur les armoires de coin carré:
Superposition
complète
Superposition
partielle
Instructions d'installation de l'armoire de coin carré
ATTENTION: N'utilisez jamais de clous pour monter des armoires. L'utilisation de clous peut annuler votre garantie d'usine, écrite ou implicite.
(6.18.13) SCB INSTRUCTIONS A5131
STEP 2
STEP 3
STEP 4
The blind panel will need to be trimmed to size to fit
over the opening of your square corner base cabinet.
Then the blind panel will need to be drilled for
installation. Mark the (8) hole locations shown to the
right on the blind panel. All holes should be located
1/4" from edges of blind panel. Drill the (8)
premarked locations with a 7/64" diameter drill bit
through the panel.
*Panel is located under cabinet with Filler Board
Locate the studs with a stud finder and mark where
the cabinets are to be installed. Remove all the doors
and drawers from the cabinets before installation.
Measure the area to confirm that the kitchen design
used will work.
Remove door and drawer from square corner
cabinet. On the square corner opening side
of the face frame (opening without door
attached), a line 1/2” from the edge of the
opening needs to be marked onto the face
frame. This will locate the blind panel for
attachment.
NOTE: Door can be placed on either side of
the cabinet depending on design needs.
DOOR LOCATION
FACE FRAME
1/2
1/2
1/2
1/2
(6.18.13) SCB INSTRUCTIONS A5131
STEP 5
STEP 6
STEP 7
Attach the blind panel to the face frame
using the recommended (8) #6 x 1/2" flat
head screws. These screws must be
purchased separately. Reattach the door
and drawer front to the cabinet.
Place the predrilled blind panel onto the
face frame using the markings placed on
the face frame in the last step. Mark the
predrilled hole locations from the blind
panel onto the face frame. Remove the
blind panel and predrill the face frame (8)
places with a 7/64" diameter drill bit, 1/2"
deep.
Position the Square Corner Base cabinet
with reference to the specifications on
page one. Do not secure to the wall yet.
SQUARE CORNER
CABINET
ADJACENT
CABINET
Z
Y
X
Filler Board
Wall
=Open Space
MARK
(8) HOLE
LOCATIONS
ONTO THE
FACE FRAME.
Attach panel to the face frame
using the (8) #6 x 1/2"
flat head screws.
10/15/2023 A5168-FRE-Rev 1
Pièces incluses:
• Armoire d'angle carrée
• Remplisseur - (Expédié sous l'armoire)
• Panneau aveugle - (Expédié sous l'armoire)
Les matériaux nécessaires :
• Vis à tête plate n° 6 x ½"
• Vis à bois à tête ronde ou à tête plate de 2 ½po
• Vis à tête ronde à rondelle de 2 ½"
(6.18.13) SCB INSTRUCTIONS A5131
Instructions for Square Corner Cabinet Installation
Parts Included:
(1) Blind Panel
(1) Square Corner Cabinet
(1) Filler Board
Tools Needed:
Phillips Head Screwdriver, Tape Measure,
Marking Tool, Drill with 7/64” Bit and 3/32”
Bit, Saw
Square Corner Cabinet Information:
STEP 1
Parts Needed:
(8) #6 x 1/2” Flat Head Screws
(2) #10 X 2 1/2” Washer Head Screws
(2) # 8 Flat Head Screws of Appropriate length
KEY
X: Minimum pull for
Square Corner Cabinet
Y: Maximum pull for
Square Corner Cabinet
Z: Minimum filler size
required between
cabinets
Min. pull is defined
when square corner or
adjacent cabinet doors
can be opened 90 deg.
and/or drawers can be
fully extended without
hitting adjacent cabinet
door/drawer when shut.
SQUARE CORNER
CABINET
ADJACENT
CABINET
Z
Y
X
Filler Board
Wall
=Open Space
Y
Min. Pull
Min. Pull w/Hardware
Max. Pull
Min. Filler Required Min. Filler Required w/Hardware
1 1/4" Overlay
3/4" 2 1/4" 12 1/2" 1" 2 1/2"
7/16" Overlay
1/4" 1 3/4" 12 1/2" 1/2" 2"
X
Z
NOTE: To determine your cabinet’s over-
lay, measure the distance from the
drawer or door to the edge of the face
frame and reference the drawing above.
Remove baseboard and other objects on the wall
area where the cabinets are to be installed. Using a
straight edge and a level, find the high point in the
floor where the cabinets are to be installed. From the
high point, mark a level horizontal line on each wall
where the cabinets will be attached. From the level
lines mark another parallel level horizontal line 35" up
for base cabinets, 54" for wall cabinets and 84", 90"
or 96", depending upon your tall cabinet heights. The
top of the base and tall cabinets and the bottom of
the wall cabinets will be located at these marks.
ATTN: FILLER BOARD AND COVER PANEL ARE STAPLED
UNDERNEATH YOUR SQUARE CORNER BASE CABINET.
Recouvrir
Min. Tirer Max. TirerMin. Tirez avec le matériel Min. Remplissage requis Min. Remplisseur requis avec matériel
Recouvrir
1/4 DU BORD
(8) LIEUX
CENTRE
CENTRE
EMPLACEMENT
DE LA PORTE
CADRE DE
VISAGE
MARQUEZ (8)
EMPLACEMENTS
DES TROUS
SUR LE CADRE
FACIAL