Installation Guide

ManualsBrandsHampton Bay ManualsLightingCreme Brulee 2-Light Kendallwood Semi-Flushmount

INSTALLATION INSTRUCTIONS

For Item#16085 (06/01/2009)

READ AND SAVE THESE INSTRUCTIONS

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

Fig. 1

Fig. 2

MOUNTING THE FIXTURE (Fig.1)

1. Carefully unpack your new fixture and lay out all the

parts on a clear area. Take care not to lose any small

parts necessary for installation.

2. Shut off power at the fuse box or circuit breaker box.

Remove the old fixture from ceiling, including the

crossbar.

3. Secure Arms (M) to Canopy (D) using Screws (F) and

Key Washer (L).

4. Thread the Bracket (H) into Center Tube (N). Align the

holes on the Arms (M) and Bracket (H) and secure

them with Screws (G).

5. Thread Studs (C) 1/4'' into the pre-drilled holes in the

Crossbar (A) spaced the same distance apart as the

holes in the Canopy (D).

6. Attach the Crossbar (A) to the Outlet Box using the

two Screws (B) from the Outlet Box. The side of the

Crossbar marked "GND" must face out.

CONNECTING THE WIRES (Fig. 2)

7. While holding the Canopy (D) toward the ceiling,

connect the electrical wires as shown in (Fig.2),

making sure that all wire connectors are secured. If

your outlet has a ground wire (green or bare copper),

connect the fixture Ground Wire to it. Otherwise,

connect the fixture Ground Wire directly to the

Crossbar using the Green Screw provided.

8. After wires are connected, tuck them carefully into the

outlet box. Place the Canopy (D) over the two Studs

(C). Secure against the ceiling with Knurled Knobs

(E).

FINISHING THE INSTALLATION (Fig. 1)

9. Install the light bulb in accordance with the fixture’s

specifications. (DO NOT EXCEED THE MAXIMUM

WATTAGE RATING!!)

10. Thread the Nipple (I) into the bottom of socket on

the Bracket. Place the Glass Shade (J) over the

Nipple (I) and tighten with Finial (K).

Your installation is now complete. Return power to the

junction box and test the fixture.

Note: Illustration (Fig.1) on this manual is for

installation purposes only. It may or may not be

identical to the fixture purchased.

LA-1487E/S

In the event that you should have any installation

question or are missing parts, please contact

Customer Service. Customer service may be reached

weekdays a 1-800-527-0998 between the hours of

8:00am and 5:00pm PST (Pacific Standard Time).

FIXTURE

WIRES

Black or

Smooth

USE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

USE

WIRES

White

(Neutral)

FIXTURE

WIRES

Bare

Copper

(Ground)

USE

WIRES

Green

(Ground)

Summary of content (2 pages)

PAGE 1
INSTALLATION INSTRUCTIONS For Item#16085 (06/01/2009) READ AND SAVE THESE INSTRUCTIONS W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R . MOUNTING THE FIXTURE (Fig.1) 1. Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation. 2. Shut off power at the fuse box or circuit breaker box. Remove the old fixture from ceiling, including the crossbar. 3.
PAGE 2
INSTRUCCIONES PARA LA INSTALACION Para Modelo# 16085 (06/01/2009) AGUARDE ESTAS INSTRUCCIONES ADVERTENCIA! CORTE LA CORRIENTE DESDE EL FUSIBLE O EL INTERRUPTOR CENTRAL. MONTANDO LA LAMPARA (Fig.1) 1. Desempaque cuidadosamente su nueva lampara y coloque todas las partes en una superfice despejada.Tenga cuidado de no perder las partes pequeñas que son necesarias para la instalacion. 2. Corte la corriente en el circuito principal y quite la lampara vieja incluyendo la barra transversal. 3.