Mounting Instructions Item No.: 372.
Foreword By choosing the senso lift-up fitting, you have opted for a fitting solution that is technically very advanced and mechanically very efficient. Your senso is manufactured with extreme care and precision and goes through numerous quality and safety checks in order to ensure that it operates smoothly and safely. 1. IMPORTANT SAFETY NOTICE The installation must be carried out in accordance with the assembly instructions; otherwise there is a risk of injury. 2.
Overview on construction sizes Cabinet height 520 mm - 800 mm 1 min. 138 K 2 **) 31 ) 5 D* 13.5 ) R* 32 20 50 Design for particle board and MDF board. Design for aluminum frame profile. *) = **) = Fitting and fixing brackets can be positioned upwards/downwards but in same mm steps. Width depending on K (Please check!).
ca. T ca. W ca. V ° K ca. 96 ca. U 32 37 H* ) 50 Cabinet Height [ mm ] D [ mm ] [ ° H K R T U V W ] 520 *) 100° 36 250 520 42 50 120 165 370 550 105° 57.5 290 550 63.5 70 115 170 380 600 100° 73.5 326 600 79.5 70 130 170 405 650 110° 67.5 340 650 73.5 150 170 260 375 720 105° 75.5 378 720 81.5 125 160 225 455 800 100° 71.5 392 800 77.
Drill holes for the senso frame according to the drilling diagram. View of right inner side. (left side symmetrical) ( Hinge with a minimum opening angle of 110° in accordance with the manufacturer’s specifications ) Drilled holes A = Ø 5 mm x min. X mm deep 32 37 Drilling depth K see chart H see chart 50 min.
Drill holes for the cabinet flap which comes in 2 parts according to the drilling diagram. Suitable for 20 mm aluminum frame profile. Number of drilled holes and drilling diagram for hinge joint as per manufacturer’s specification. View of central hinge joint on the reverse side of the flap frame. 20 For a flap width of 900 mm upwards we recommend 3 central hinge joints.
Drill holes for the cabinet flap which comes in 2 parts according to the drilling diagram. Design for particle board and MDF board. For a flap width of 900 mm upwards we recommend 3 central hinge joints. Number of drilled holes and drilling diagram for hinge joint as per manufacturer’s specification. View of central hinge joints on the reverse side of the flap.
5 Screw the central hinge joints onto the cabinet flap which comes in 2 parts. Design for aluminum frame profile. Design for particle board and MDF board.
6 Screw flap supports onto bottom part of cabinet flap. Design for aluminum frame profile. M4x16 (DIN 965) max. ø 4x16 M4x10 ISO 7045 (DIN 7985) Flap support with long-hole for 20 mm Aluminum frame profile (included in SET, needs to be stated on order, otherwise “Standard” is being delivered.
Design for particle board and MDF board. Flap support for wood-, particle board and MDF board or wide frames as of 40 mm.
7 Pre-mount hinge joints on the top of cabinet flap according to the manufacturer’s specifications. 8 Screw on the right and left base fixing plate.
9 Screw on senso-fitting. The fitting can be used for both sides (right and left)! Please Note The lifting arm of the senso frame must be in the open position (supply condition), otherwise there is a risk of injury. Fitting is under spring tension.
10 Insert the cabinet flap into the hinge joints and fix securely. We recommend Cross-mounting plates with three mounting holes. 11 Insert lifting arms (open position) into flap supports and secure with bolt.
12 Adjust flap, if necessary. (Fitting is pre-set by factory) X X X The adjustment of the center pulling-in of the flaps is done through the Exenter-screw (see scale). SW 8 , The adjustment of the final stop (abt. 12 mm) pre-set by the factory, is done through the stop-screw.To do this pull the lifting-arm / flap slightly downwards. min. 9 mm max.
max. kg The power-adjustment for the flapweight is done through the hexagonal screwnut. (See scale) To do this pull lifting arm / flap downwards and adjust as shown. max. 20 mm min. SW 4 If everything has been adjusted correctly the flap will stop in any position from abt. 20 cm opening on. 13 Install the housing-cover.
14 Choosing the correct senso-model The correct model of the senso results from the height and weight of the flaps. See chart. Cabinet Height Door weight / Part-No. [ mm ] [ kg ] 520 ( 500 – 540 ) 550 ( 540 – 580 ) 3.0 – 6.5 03.3674.003.001 6.0 – 12.0 03.3674.003.002 9.0 – 18.0 03.3674.003.003 12.0 – 24.5 03.3674.003.004 600 ( 580 – 640 ) 3.0 – 6.0 03.3674.001.001 6.0 – 11.0 03.3674.001.002 9.0 – 17.0 03.3674.001.003 12.0 – 23.0 03.3674.001.004 650 ( 640 – 700 ) 3.0 – 5.5 03.3674.005.
