H2oEliteLabs Max i Residential model - indoor installation Operation Manual H2oEliteLabs.
Table of Contents Page 2: Table of contents Page 3: What’s included, Types of pipes that can be used and Elite Max i specs Page 4: Installation location Page 5: Mounting the control module, installing the induction coil Page 6: Installing the induction coil, coil chart Page 7: Coil chart, connecting the power adapter Page 8: Connecting induction coil, Features and notifications Page 9: Optional Equipment, Technology and how it works Page 10: Benefits of the H2oEliteLabs Max i Page 11: Warranty information a
What’s Included EWC-Elite Max I Control module AC adapter (115 volt class, UL approved) Signal cable AWG18 (60’) 4 Nylon cable ties Screws and wall anchors Types of pipes that can be used with Elite-Max i Copper Pipe PVC Pipe CPVC Pipe PEX Pipe Please note: The EWC Max i cannot be used on galvanized pipe or any kind of steel pipe. In the event that galvanized or steel pipe is present. A section of the galvanized or steel pipe must be removed and replaced with copper, PVC or PEX pipe.
Installation Location 1. Determine where the main cold water line enters the house or condominium. Ideal location for induction coil 2. Apply induction coil to main cold water line. If the main cold water line is not assessable then apply induction coil to the incoming cold water line to water heater or tankless water heater. Only hot water appliances will have treatment if the induction coil is applied to the hot water.
Mounting the control module The control module can be mounted on any type of wall or surface with supplied mounting hardware. Supplied hole template can be used to mark screw spacing. There are two mounting holes located on the back of the control module. Mounting holes with 3”(76.2mm) center to center spacing Screws and wall anchors Installing the induction coil 1.
Installing the induction coil (continued) 9. Installing the induction coil on copper pipe will need a double layer coil. Wrap the first layer coil as mentioned on the previous page. 10. When finished wrapping the first layer and securing to the pipe with a cable tie, then another layer of wrapping must be applied on top of the first layer of wrappings with the remaining wire. 11.
Coil Chart for Copper Note: Always use specified length and layers of wraps for your pipe size. NPS Pipe size Layers Approx. Coil Length 1/2” Double 6” 5/8” Double 6” 3/4” Double 6” 1” Double 5.5” 1 1/4” Double 5” 1 1/2” Double 4.5” Connecting the Power Adapter The control module comes with a 115 VAC power adapter with a 5’ cord. Part number: CUI/SW125-5-N-P5. Only use supplied power supply. This must be inserted into the power receptacle jack in the bottom of the control module.
Connecting Induction Coil 1. Upon completion of installing the induction coil, the two wires leading from the induction coil must be connected to the control module. 2. You will need to strip approximately .5” of the wire insulation from each wire. 3. There are two illuminated holes in the bottom of the control module to receive the stripped wire ends. 4. To insert the coil wires into the control module there are two illuminated push buttons located on the front of the control module.
Optional Equipment The Elite Max i is equipped with an optional water leak detection module . The water leak detection module will alert the user with an audible and visual notification in the event of a water leak. The leak detection module should be installed on the floor where there is a possibility for water leaks.
Benefits of the H2oEliteLabs Max i The most outstanding feature of the H2oEliteLabs Max i, is that it’s completely maintenance free. No, salt, no chemicals, no batteries, totally solid state design and no expensive repairs. H2oEliteLabs is environmentally friendly without the use of salt and leaving essential minerals it is also better for your health. To harness the full effect of the H2oEliteLabs Max i it may take up to 90 days to completely remove scale buildup from the entire plumbing system.
Warranty information and Product Support H2oEliteLabs Max i The H2oElite Max i has a warranty period of 3 years from the date of purchase. Free of defects in material and workmanship under normal use. This warranty does not extend to any water or electrical appliances or damaged plumbing nor other damages that occurred before or after installation. The manufacture in no way will be liable for damages from improper installation or damaged pipes or any other damages directly or indirectly.
H2oEliteLabs.
