Use and Care Manual

EXHAUSTFAN
RULES FOR SAFE OPERATION
1.D o not depend on any switch as the sole means of disconnecting power when installing
or servicing the fan.
2.A lways disconnect, lock-out, and tag-out power source before installing or servicing. Failure
disconnect power source can result in fire, shock, or serious injury.
3.M otor will restart without warning after thermal protector trips. Do not touch operating motor;
it may be hot enough to cause injury.
4.D o not place body parts or objects in fan or motor openings while motor power is connected to the
source.
5. All electrical connections should be made by a qualified electrician.
6. These utility exhaust fans are for general purpose exhaust applications only. Do not use these
exhaust fans in an area where corrosive or explosive materials may be found.
7. Follow all local and state/provincial electrical and safety codes in the United States and
Canada, as well as the National Electrical Code (NEC) Act and the Occupational Safety and Health
(OSHA) in the United States, and the Canadian Electric Code (CEC) in Canada.
8. Always disconnect power source before working on or near a motor or its connected load.
1. The motor amperage and voltage ratings must be checked for compatibility to supply voltage prior to final
electrical connection.Please refer to the motor's nameplate label.
2. This product is to be used indoors.
3. Wiring must conform to local,state , and national codes.
4. This appliance is not intended for use by persons(including children )with reduced physical,sensory or
mental capabilities ,or lack of experience and knowledge,unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
5. Children should be supervised to ensure that they do not play with the appliance.
IPOWER wattants this product to be free of defects in material and workmanship for the
applicaitons specified in the owner's manual for a period of one year from date of purchase. This
warranty only applies to the original purchaser of this product.
This warranty excludes damage, accidental or otherwise, to the unit not caused by a
defect in material or workmanship.
The warranty also excludes damage caused by misuse, tampering, modificaiotn,
misassembly, repairs or alterations, or failure to adequately maintain and care for the unit.
Operation this product under any conditions other than those recommended or at voltages
other than indicated will also void this warranty. For warranty issues, contact the place of
purchase for repair/replacement opportunities. The original dated receipt or proof of
purchase must accompany all returns.
All warranties, expressed or implied, are limited for one year from the date of purchase.
IPOWER is a registered trademark of BRTH INC. Unless proscribed by law, BRTH INC,
shall not be, liable for any personal injury, propertu, or any incidental or consequential
damafe of any kind resultign from malfuctions, defects, misuse, improper assembly or
installation, or alteration of this product.
Some states do not allow for the limitation or exclusion of incidental or consequential
damages, or do not allow limitation on implied warranties. The above limitations and
exclusions may not apply to you. This warranty gives you specific legal rights, and may
also include other rights.
OPERATING INSTRUCTIONS
1. Keep the area free of objects that could impede air flow on both the
intake and exhaust side of fan.
2. For proper exhaust operation, a window, door, or louver should be
opened for fresh air intake on the opposite side of the area to be
ventilated.
3. Turn the fan ON; the shutter will open automatically. When the unit is
turned OFF, the shutter will close.
MAINTENANCE
1. Disconnect power source before servicing.
2. Periodically clean off accumulated dirt from the propeller, guard, motor, and shutter.
-3-
-4-
Metal
Vertical
Power source
Mounting Position
Frame Material
Propeller Material
Metal
115 60 60 1510
Rotational Speed
R/min
A
13.58
14.96
17.71
B
19.09
21. 25
24. 8
14.44
16.9
20.47
C
7.28
7.87
7.87
D E
15.35
18.11
21.45
Exhaust
fan
Product parameters:
HIFANXVENTIL14THEMOT
HIFANXVENTIL16THEMOT
HIFANXVENTIL20THEMOT
HIFANXVENTIL14THEMOT
HIFANXVENTIL16THEMOT
HIFANXVENTIL20THEMOT
115 60 98 1480
115 60 148 1080
E
D
B
C
A
F
F
3.74
4.52
4.52
NOTE: Allowing the fan frame to flex or move will result in excesess vibrations,which may
cause possible premature shutter failure.
2. Connect power to the motor using an approved wiring methodhod.Refer to the following
wiring diagram:Figure1
Figure1: wiring Diagram-Single speed. 120-volt connection.
READ AND FOLLOW ALL INSTRUCTION BEFORE OPERATING FAN
-1-
-2-
switch
Green
White
Black
Thermal protector
Motor