Submittal Sheet

ManualsBrandsGrundfos ManualsCirculator PumpsTPE100-160/2 E-Circulator Pump w/ Differential Pressure Sensor, 3 HP, Bronze, 208-230V, GF 100 Flange Mount

Company name:

Created by:

Phone:

Fax:

Date:

Printed from Grundfos CAPS [2011.05.069]

Position Count Description Unit price

-1 On

request

TPE 100-160/2-S B U-G-Z-BUBE

Product photo could vary from the actual product

Product No.: 91136606

Single-stage, centrifugal, in-line, single-head

pump.

The in-line design with opposite suction and

discharge ports enables mounting in pipework or

on a concrete foundation.

The shaft seal is a corrosion resistant

maintenance-free mechanical seal.

The pump is fitted with a three-phase

MLE motor with frequency converter and

PI-controller integrated in the motor terminal

box. No additional motor protection is required as

both motor and electronics are protected by

integrated overload and temperature protection.

A differential pressure transmitter fitted on the

pump registers the differential pressure across

the pump and enables constant pressure or

proportional pressure control of the pump.

A control panel enables setting of required

setpoint as well as setting of pump to MIN or MAX

operation or to STOP. The control panel has

indicator lights for "Operation" and "Fault".

Communication with the pump is possible by means

of Grundfos R100 Remote Control enabling further

settings as well as reading out of a number of

parameters such as "Actual value", "Speed",

"Power input" and total "Power consumption".

The terminal box holds terminals for the

connection of :

- Pump start/stop (potential-free contact),

1/6

Summary of content (6 pages)

PAGE 1
Company name: Created by: Phone: Fax: Date: Position Count -1 - Description Unit price TPE 100-160/2-S B U-G-Z-BUBE On request Product photo could vary from the actual product Product No.: 91136606 Single-stage, centrifugal, in-line, single-head pump. The in-line design with opposite suction and discharge ports enables mounting in pipework or on a concrete foundation. The shaft seal is a corrosion resistant maintenance-free mechanical seal.
PAGE 2
Company name: Created by: Phone: Fax: Date: Position Count Description - Unit price external remote setpoint setting via analog signal, 0 - 5 V, 0 - 10 V, 0(4) - 20 mA, 5 V voltage supply for setpoint potentiometer, Imax = 5 mA, differential pressure sensor factory-fitted, input for forced control to MIN or MAX (potential-free contact), potential-free fault signal relay with changeover contact, RS485 GENIbus. Liquid: Liquid temperature range: Liquid temp: 5 ..
PAGE 3
Company name: Created by: Phone: Fax: Date: Description Product name: Product Number: EAN number: Value TPE 100-160/2-S B U-G-Z-BUBE U-G-Z BUBE 91136606 5700838117189 - H 100 % (ft) TPE 100-160/2-S B 3* 220 V, 60 Hz Pumped liquid = Water Liquid temperature = 68 °F Density = 62.
PAGE 4
Company name: Created by: Phone: Fax: Date: - 91136606 TPE 100-160/2-S B 60 Hz cos phi eta 1 TPE 100-160/2-S B + 90FA I (A) 10 3 HP 3* 220 V, 60 Hz cos phi I eta 0.8 8 0.6 6 0.4 4 0.2 2 0 0 n (rpm) 0.5 3000 1 1.5 2 2.5 3 P2(HP) 0 n P1 (kW) P1 3 2500 2000 2 1500 1000 1 500 n = 100 % 0 Printed from Grundfos CAPS [2011.05.
PAGE 5
Company name: Created by: Phone: Fax: Date: - 91136606 TPE 100-160/2-S B 60 Hz 4 15/16" M16 6 9/16" 10 3/8" 25 9/16" 4 15/16" 3 15/16" 4 13/16"7 7/16" 3/4" NPT 1/4 4 3/16" 6 3/16" 10 1/2" 21" 7 9/16" 9 1/16" Note! All units are in [mm] unless others are stated. Disclaimer: This simplified dimensional drawing does not show all details. Printed from Grundfos CAPS [2011.05.
PAGE 6
Company name: Created by: Phone: Fax: Date: - 91136606 TPE 100-160/2-S B 60 Hz L1 L2 L3 0-10 V 0/4-20 mA 4-20 mA 1 9 8 7 B Y A 1: 9: 8: 7: B: Y: A: Digital input GND (frame) +24 V Sensor input RS-485B Screen RS-485A Group 1 1/0 Group 3 Group 2 NC C NO STOP 6: GND (frame) 5: +10 V 4: Setpoint input 3: GND (frame) 2: Start/stop RUN 0/4-20 mA 0-10 V 10K 6 5 4 3 2 All units are [mm] unless otherwise presented. Printed from Grundfos CAPS [2011.05.