Installation Guide

ManualsBrandsGROHE ManualsBathParkfield Single-Handle 1-Spray Tub and Shower Faucet in Brushed Nickel InfinityFinish (Valve Sold Separately)

.....1

.....6

.....11

.....16

.....21

.....26

.....2

.....7

UAE

.....12

.....17

EST

.....22

.....27

.....3

.....8

.....13

.....18

.....23

RUS

.....28

.....4

.....9

.....14

SLO

.....19

.....24

.....5

FIN

...10

.....15

.....20

.....25

DESIGN + ENGINEERING

GROHE GERMANY

www.grohe.com

19 921

PARKFIELD

99.0006.031/ÄM 225453/09.13

Summary of content (12 pages)

PAGE 1
PARKFIELD DESIGN + ENGINEERING GROHE GERMANY 99.0006.031/ÄM 225453/09.13 www.grohe.com 19 921 D .....1 GB F E I .....2 NL .....6 S .....7 .....3 DK .....8 .....4 .....5 N .....9 FIN ...10 PL .....11 .....16 BG .....21 CN .....26 UAE .....12 TR .....17 EST .....22 UA .....27 GR .....13 SK .....18 LV .....23 RUS .....28 CZ .....14 SLO .....19 LT .....24 H P .....15 HR .....20 RO .....
PAGE 2
Please pass these instructions on to the end user of the fitting! S.v.
PAGE 3
5 015 19 921 II 2
PAGE 4
1 2 I1 D B E1 C G I H E B A A1 3 4 D F 5 H K L J M J1 3mm 4 3
PAGE 5
English Installation 1. Remove the two screws (A1) from the fitting template (A), then remove the template, see Fig. [1]. 2. Turn the valve stem (B) clockwise to the OFF position. 3. Make sure the water supply is turned on at the service stop valves (C). Stop valves must be in fully open position (slots horizontal) for valve to function. 4. The adjustable hot water limit stop (D) is factory set at neutral position to give maximum outlet temperature, see Figs. [2] and [3].
PAGE 6
7 D F 0 D 8 9 B E1 E 6 5 D1
PAGE 7
English Maximum hot water limit setting The adjustable hot water limit stop (D) is factory set in a neutral position (0), see Fig. [6]. On applications requiring to limit the valve opening from full hot position, the factory set adjustable hot water limit stop must be reset as described below. 1. Remove the factory set adjustable hot water limit stop (D), see Fig. [7]. 2. Slide the adapter (E) onto the valve stem (B), by placing the lever stop pin (E1) on top of "Arrow" ↑ (F), see Figs. [6] and [8]. 3.
PAGE 8
10 11 H C J J1 K L M 3mm 12 O O1 N I I2 H 13 14 P R 7
PAGE 9
English Maintenance Check, clean and if necessary, replace parts. Grease with special valve grease. Pressure balancing cartridge, see Figs. [10] to [14]. 1. Lever out plug (M) and loosen set screw (L) with a 3mm wrench, see Fig. [10]. 2. Pull off lever (K). 3. Detach screws (J1) and remove escutcheon (J). 4. Shut off hot and cold water stops (C). The slots are vertical when the stops are in the off position, see Fig. [11]. 5. Pull off cap (H), loosen screws (I2) and detach plastic guide (I), see Fig. [12].
PAGE 10
PAGE 11
PAGE 12
D & +49 571 3989 333 impressum@grohe.de A & +43 1 68060 info-at@grohe.com AUS Argent Sydney & +(02) 8394 5800 Argent Melbourne & +(03) 9682 1231 B & +32 16 230660 info.be@grohe.com BG & +359 2 9719959 grohe-bulgaria@grohe.com CAU & +99 412 497 09 74 info-az@grohe.com CDN & +1 888 6447643 info@grohe.ca CH & +41 448777300 info@grohe.ch CN & +86 21 63758878 CY & +357 22 465200 EST & +372 6616354 grohe@grohe.ee F & +33 1 49972900 marketing-fr@grohe.