MODEL G0454ZX 20" PLANER w/SPIRAL CUTTERHEAD OWNER'S MANUAL (For models manufactured since 06/23) COPYRIGHT © MAY, 2023 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #MNLW22721 PRINTED IN CHINA ***Keep for Future Reference*** V1.05.
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use.
Table of Contents INTRODUCTION................................................ 2 Contact Info.................................................... 2 Manual Accuracy............................................ 2 Identification.................................................... 3 Controls & Components.................................. 4 Internal Components...................................... 5 Machine Data Sheet....................................... 6 SECTION 1: SAFETY......................................
INTRODUCTION Contact Info Manual Accuracy We stand behind our machines! If you have questions or need help, contact us with the information below. Before contacting, make sure you get the serial number and manufacture date from the machine ID label. This will help us help you faster. We are proud to provide a high-quality owner’s manual with your new machine! Grizzly Technical Support 1815 W. Battlefield Springfield, MO 65807 Phone: (570) 546-9663 Email: techsupport@grizzly.
Identification Become familiar with the names and locations of the controls and features shown below to better understand the instructions in this manual. Control Panel for Magnetic Switch Return Roller (1 of 2) Cast-Iron Extension Wing (1 of 2) Dust Hood Table Height Handwheel Gearbox Belt Cover Foot Pedal Table Height Scale Feed Rate Control Knob Table Lock (1 of 2) Lifting Bars (2 of 4) To reduce your risk of serious injury, read this entire manual BEFORE using machine. Model G0454ZX (Mfd.
Controls & Components D To reduce your risk of serious injury, read this entire manual BEFORE using machine. F E I G Refer to the following figures and descriptions to become familiar with the basic controls and components of this machine. Understanding these items and how they work will help you understand the rest of the manual and minimize your risk of injury when operating this machine. Control Panel A B C Figure 1. Control panel components. A. POWER Switch: Turns incoming power ON and OFF.
Internal Components C A E D F B G Workpiece I H H Figure 3. Workpiece path and major planing components (side cutaway view). A. Anti-Kickback Fingers: Provide additional safety for operator. B. Serrated Infeed Roller: Pulls workpiece toward cutterhead. C. Chip Breaker: Breaks off chips created by cutterhead to prevent tearout, and diverts chips to dust port. D. Cutterhead: Holds indexable carbide inserts that remove material from workpiece. E. Chip Deflector: Directs chips into dust hood.
Machine Data Sheet MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0454ZX 20" PLANER WITH SPIRAL CUTTERHEAD Product Dimensions: Weight.............................................................................................................................................................. 812 lbs. Width (side-to-side) x Depth (front-to-back) x Height...........................................................................
Cutterhead Info Cutterhead Type........................................................................................................................................ Spiral Cutterhead Diameter .......................................................................................................................... 3-3/16 in. Number of Cutter Rows....................................................................................................................................
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating This Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
WEARING PROPER APPAREL. Do not wear clothing, apparel or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to reduce risk of slipping and losing control or accidentally contacting cutting tool or moving parts. HAZARDOUS DUST. Dust created by machinery operations may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with each workpiece material.
Additional Safety for Planers Amputation, serious cuts, entanglement, or death can occur from contact with rotating cutterhead or other moving parts! Flying chips can cause eye injuries or blindness. Workpieces or knives thrown by cutterhead can strike nearby operator or bystanders with deadly force. To reduce the risk of these hazards, operator and bystanders MUST completely heed hazards and warnings below. KICKBACK. Know how to reduce risk of kickback and kickback-related injuries.
SECTION 2: POWER SUPPLY Availability Circuit Information Before installing the machine, consider the availability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize the risk of electrocution, fire, or equipment damage, installation work and electrical wiring must be done by an electrician or qualified service personnel in accordance with all applicable codes and standards.
Grounding Requirements This machine MUST be grounded. In the event of certain malfunctions or breakdowns, grounding reduces the risk of electric shock by providing a path of least resistance for electric current. This machine is equipped with a power cord that has an equipment-grounding wire and a grounding plug. Only insert plug into a matching receptacle (outlet) that is properly installed and grounded in accordance with all local codes and ordinances.
SECTION 3: SETUP Needed for Setup This machine presents serious injury hazards to untrained users. Read through this entire manual to become familiar with the controls and operations before starting the machine! Wear safety glasses during the entire setup process! HEAVY LIFT! Straining or crushing injury may occur from improperly lifting machine or some of its parts. To reduce this risk, get help from other people and use a forklift (or other lifting equipment) rated for weight of this machine.
Inventory B The following is a list of items shipped with your machine. Before beginning setup, lay these items out and inventory them. If any non-proprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store. C D NOTICE E F If you cannot find an item on this list, carefully check around/inside the machine and packaging materials.
Hardware Recognition Chart USE THIS CHART TO MATCH UP HARDWARE DURING THE INVENTORY AND ASSEMBLY PROCESS. Flat Head Cap Screw 5mm 5mm Model G0454ZX (Mfd.
Cleanup The unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corrosion during shipment and storage. This rust preventative works extremely well, but it will take a little time to clean. Be patient and do a thorough job cleaning your machine. The time you spend doing this now will give you a better appreciation for the proper care of your machine's unpainted surfaces.
Site Considerations Weight Load Physical Environment Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be installed on the machine, and the heaviest workpiece that will be used. Additionally, consider the weight of the operator and any dynamic loading that may occur when operating the machine.
Lifting & Placing HEAVY LIFT! Straining or crushing injury may occur from improperly lifting machine or some of its parts. To reduce this risk, get help from other people and use a forklift (or other lifting equipment) rated for weight of this machine. The Models G0454ZX requires the use of lifting equipment such as a forklift, engine hoist, or boom crane. DO NOT attempt to lift or move the planer without the necessary assistance of other people.
5. 6. Line up notch in handwheel bore with preinstalled key, slide handwheel onto shaft, and secure with M12-1.75 hex nut and 12mm flat washer (see Figure 10). 8. Remove front base cover (see Figure 12). 9. Position foot pedal mount over crosspiece at front of machine base (see Figure 12). Thread handle into rim of handwheel and tighten to secure (see Figure 10). 10. Secure foot pedal from front to back using (2) M10-1.5 x 55 hex bolts, (4) 10mm flat washers, and (2) M10-1.
Dust Collection This machine creates a lot of wood chips/ dust during operation. Breathing airborne dust on a regular basis can result in permanent respiratory illness. Reduce your risk by wearing a respirator and capturing the dust with a dust-collection system. Minimum CFM at Dust Port: 600 CFM Do not confuse this CFM recommendation with the rating of the dust collector.
Test Run 5. Move POWER switch to ON position. 6. Twist STOP button clockwise until it springs out (see Figure 15). This resets switch so machine can start. Once assembly is complete, test run the machine to ensure it is properly connected to power and safety components are functioning correctly. If you find an unusual problem during the test run, immediately stop the machine, disconnect it from power, and fix the problem BEFORE operating the machine again.
Recommended Adjustments The adjustments listed below have been performed at the factory. However, because of the many variables involved with shipping, we recommend that you verify the adjustments to ensure the best possible results from your new machine. Step-by-step instructions for these adjustments can be found in the SERVICE section starting on Page 35. -22- Factory adjustments that should be verified: • • • V-belt tension (Page 38). Table height scale calibration (Page 43).
SECTION 4: OPERATIONS Operation Overview The purpose of this overview is to provide the novice machine operator with a basic understanding of how the machine is used during operation, so the machine controls/components discussed later in this manual are easier to understand. Due to the generic nature of this overview, it is not intended to be an instructional guide.
workpiece inspection Workpiece Inspection Some workpieces are not safe to use or may require modification before they are. Before cutting, inspect all workpieces for the following: • • • • • • -24- Material Type: This machine is only intended for workpieces of natural wood fiber Attempting to use workpieces of any other material that may break apart during operation could lead to serious personal injury and property damage.
Planing Tips Planing Tips • Inspect your lumber for twisting or cupping, and surface one face on a jointer if necessary before planing workpiece. • Scrape off all glue when planing glued-up panels. Dried glue can quickly dull knives/ inserts. • DO NOT plane more than one piece at a time. Never plane multiple pieces side by side. • Never remove more than the recommended amount of material on each pass. Only remove a small amount of material on each pass when planing wide or dense stock.
Pitch & Glue Build-up Problem: Glue and resin buildup on the rollers and cutterhead will cause overheating by decreasing cutting sharpness while increasing drag in the feed mechanism. The result can include scorched lumber, uneven knife/insert marks, and chatter. Solution: Clean the rollers and cutterhead. Chip Marks or Indentations Problem: Chip indentation or chip bruising is the result of wood chips not being thrown away from the cutterhead and out of the machine.
Setting Feed Rate Bed Roller Height High Feed Rate........................................20 FPM Low Feed Rate.........................................15 FPM Bed Roller Height Range...............0.002"–0.020" The infeed and outfeed rollers move the workpiece through the planer while keeping it flat and providing a consistent rate of movement. The speed that these rollers move the workpiece through the planer is the feed rate.
Rotating/Replacing Cutterhead Inserts Tools Needed Qty Hex Wrench 3mm............................................... 1 Wrench or Socket 14mm.................................... 1 Rotacator (Optional)........................................... 1 To adjust bed roller height: 1. DISCONNECT MACHINE FROM POWER! 2. Lower table all the way down to give yourself room to work. 3. Loosen set screws above each of four roller adjustment cams—two on each side (see Figure 20).
4. Remove any sawdust or debris from head of insert, Torx screw, and surrounding area (see Figure 22). 6. — When all four insert cutting edges have been used, replace insert with a new one. Always position insert reference dot in same position when installing a new insert to aid in rotational sequencing. Torx Screw Cutterhead Insert Figure 22. Cutterhead inserts and Torx screws (chip deflector removed for better clarity). 5.
ACCESSORIES SECTION 5: ACCESSORIES Installing unapproved accessories may cause machine to malfunction, resulting in serious personal injury or machine damage. To reduce this risk, only install accessories recommended for this machine by Grizzly. H7319—Indexable Carbide Inserts, 10-Pk. These replacement carbide inserts measure 14 x 14 x 2mm and come in a 10-pack. Great to have on hand. NOTICE Refer to our website or latest catalog for additional recommended accessories.
SECTION 6: MAINTENANCE To reduce risk of shock or accidental startup, always disconnect machine from power before adjustments, maintenance, or service. Schedule For optimum performance from this machine, this maintenance schedule must be strictly followed.
Suggested Lubricants SB1365—South Bend Way Oil-ISO 68 Engineered for the high pressure exerted on horizontal or vertical ways and slides. Protects against rust and corrosion. Ensures stick-free, smooth motion which maximizes finishes and extends the life of your machine. Won’t gum up! 12 oz. AMGA#2 (ISO 68 Equivalent). Items Needed Qty Hex Wrench 6mm............................................... 1 Wrench or Socket 10mm.................................... 1 Phillips Head Screwdriver #2.....................
Sprockets (2 of 5) Table Height Chain Fill Plug Figure 29. Example of table height chain and sprockets (viewed from underneath base). Gearbox Oil Oil Type............... T28042 or ISO 320 Equivalent Oil Amount..................................................20 Oz. Frequency........ After First 20 Hours, Then Yearly Note: We recommend that you replace the gearbox oil after the first 20 hours of operation.
Columns & Leadscrews Oil Type.................SB1365 or ISO 68 Equivalent Oil Amount.............................................Thin Coat Grease Type......... T26419 or NLGI#2 Equivalent Frequency............... Every 40 Hours of Operation The table rides on the columns and is moved by the rotation of the leadscrews inside the columns. Loosen the dust sleeve (see Figure 33) to access the columns and leadscrews.
Service SECTION 7: SERVICE Review the troubleshooting procedures in this section if a problem develops with your machine. If you need replacement parts or additional help with a procedure, call our Technical Support. Note: Please gather the serial number and manufacture date of your machine before calling. Troubleshooting Motor & Electrical Symptom Possible Cause Possible Solution Machine does not start, or power supply breaker immediately trips after startup. 1. 2. 3. 4. 1. 2. 3. 4.
Motor & Electrical (Cont.) Symptom Possible Cause Machine has 1. Motor or component loose. vibration or noisy operation. 2. Mobile stand feet not adjusted properly. 3. V-belt(s) worn, loose, pulleys misaligned or belt slapping cover. 4. Insert(s) at fault. 5. Pulley loose. 6. Motor mount loose/broken. 7. Motor fan rubbing on fan cover. 8. Bed rollers protruding unevenly. 9. Cutterhead bearings at fault. 10. Centrifugal switch needs adjustment/at fault. 11. Motor bearings at fault. Possible Solution 12.
Operation (Cont.) Symptom Possible Cause Possible Solution Chipping/ indentation in workpiece surface (inconsistent pattern). 1. Chips aren't being properly expelled from cutterhead. 2. Chip breaker not set correctly. 1. Use proper dust collection system. Fuzzy grain. 1. Wood may have high moisture content or surface wetness. 2. Dull insert(s). 1. Check moisture content is below 20% and allow to dry if moisture is too high (Page 24). 2. Rotate/replace insert(s) (Page 28).
Tensioning/ Replacing V-Belts 2. Remove belt cover to expose belts and pulleys, as shown in Figure 35. Note: A collection of black belt dust at the bottom of the belt cover is normal during the life of the belts. After approximately 16 hours of operation, V-belts will stretch and seat into pulley grooves and need to be properly tensioned to avoid severely reducing life of V-belts.
4. If V-belts need to be replaced, raise motor to release belt tension, roll them off pulleys, then replace them as a matched set of three. 5. To adjust V-belt tension, loosen top motor mount hex nuts (see Figure 36 on Page 38), then adjust bottom hex nuts to raise or lower motor. Note: V-belts are correctly tensioned when there is approximately 3⁄4" deflection when moderate pressure is applied to them midway between pulleys, as illustrated in Figure 37.
Using a Rotacator 8. Items Needed Qty Hex Wrenches 3, 6mm.................................1 Ea. Wrench or Socket 10, 13mm........................1 Ea. Rotacator............................................................ 1 To use a Rotacator: 1. DISCONNECT MACHINE FROM POWER! 2. Ensure all inserts are properly installed (refer to Rotating/Replacing Cutterhead Inserts on Page 28 for detailed instructions). 3. Lower table at least 4" below headstock, then lock it in position. 4.
12. Use same zero reference on Rotacator dial from Step 5, perform similar steps as described above to adjust height of chip breaker to its recommended specification given at beginning of this subsection. Adjustment controls are shown in Figure 41. Using Wood Blocks Items Needed Qty Hex Wrenches 3, 6mm.................................1 Ea. Wrench or Socket 10, 13mm........................1 Ea. 2x4 6' Long......................................................... 1 Feeler Gauge Set...........................
5. Remove dust hood, top cover, belt cover, and gearbox cover. 6. Raise table until wood blocks get close to cutterhead. 7. Use belt to rotate cutterhead, and continue raising table until blocks just barely touch cutterhead insert at its lowest point of rotation (BDC), then lock table in place. Note: Upward pressure of wood blocks will hold infeed and outfeed rollers, chip breaker, and pressure bar at same level as insert at BDC. 8.
Positioning Chip Deflector Calibrating Table Height Scale Chip Deflector Gap Setting................... 1⁄ 16''–1⁄ 8'' Although correctly set at the factory, the table height scale can be adjusted for accuracy if necessary. When properly distanced from the cutterhead, the chip deflector directs the chips into the dust hood, and keeps them from falling onto the outfeed roller and being pressed into the workpiece. Tools Needed: Qty Wrench or Socket 10, 13mm........................1 Ea.
Tensioning Table Height Chain The table height chain transfers movement from the table height handwheel to the columns that control table height. The chain drive can be adjusted to remove slack if the chain stretches over time or is loosened during table leveling procedures. Tools Needed Qty Hex Wrenches 4, 6mm.................................1 Ea. Aligning Pulleys Proper pulley alignment prevents premature V-belt wear and unnecessary load on the motor.
Adjusting Table Parallelism Maximum Allowable Tolerances: Cutterhead/Table Side-to-Side................... 0.002" Head Casting/Table Front/Back................. 0.020" Table parallelism is critical to the operation of the machine. As such, it is essential that the table is parallel with the cutterhead (within 0.002") from side-to-side, as illustrated in Figure 50. The easiest way to determine if your table has a parallelism problem is to plane a workpiece and measure the thickness in multiple locations.
3. Loosen lock screws and idler sprocket (see Figure 52). Idler Sprocket Figure 52. Location of idler sprocket and lock screws. 4. 6. -46- Repeat Steps 4–6 with each sprocket that needs to be adjusted until table-to-cutterhead clearance is within 0.008" from one side to the other. 8. Make sure chain is properly fitted on sprockets, then tighten idler sprocket and cap screws. 9.
Tensioning Drive Chain 3. Loosen lock bolt (see Figure 54) that secures idler bracket to gearbox, then push idler wheel against chain with moderate pressure to eliminate slack in chain. While maintaining pressure on idler wheel, tighten hex bolt. The drive chain system transfers power from the cutterhead to the infeed and outfeed rollers. The chain drive can be adjusted to remove slack if the chain stretches over time. Idler Bracket Idler Wheel Items Needed Qty Hex Wrench 6mm...........................
SECTION 8: WIRING These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Compare the manufacture date of your machine to the one stated in this manual, and study this section carefully. If there are differences between your machine and what is shown in this section, call Technical Support at (570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine.
wiring diagram Wiring Diagram Control Box To Power Supply N L N1 L1 Hot To Electrical Box Y 3 4 2 0 2 X2 2 3 X2 1 L1 1 4 X1 4 2 5 POWER SWITCH NHD NCS-P5P298D101 SA1 2 X1 4 START BUTTON NHD NLB22-F10GA SB2 CB-10 N1 0 PL-BA9 L N Ground Ground 1 CB-01 X Hot 2 To Electrical Box PL-BA9 220 VAC L6-30 PLUG 0 5 CB-10 G 4 3 STOP BUTTON NHD NLB22-R11RA SB1 Electrical Box L1 0 N1 1 Circuit Breaker 3L2 1L1 5L3 N1 L1 KM1 13NO Centrifugal Switch 13NO 21NC 21
Electrical Components Figure 55. Electrical box wiring. -50- READ ELECTRICAL SAFETY ON PAGE 48! Model G0454ZX (Mfd.
Figure 56. Control box wiring. Figure 57. Motor junction box wiring. Model G0454ZX (Mfd.
SECTION 9: PARTS We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown are available for purchase. Call (800) 523-4777 or visit www.grizzly.com/parts to check for availability.
Headstock Parts List (Cont.) REF PART # DESCRIPTION REF PART # DESCRIPTION 14 15 19 20 21 22 23 24 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 53 53-1 53-2 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 ROLLER STAND CAP SCREW M6-1 X 16 DUST HOOD 5" FLANGE BOLT M6-1 X 12 TOP COVER FLANGE BOLT M6-1 X 12 FOAM PIECE CHAIN DRIVE COVER CAP SCREW M8-1.
Table 210 213 211 212 207 209 208 204 205 203 202 206 209 207 210 206 208 201 214 REF PART # DESCRIPTION REF PART # DESCRIPTION 201 202 203 204 205 206 207 MAIN TABLE ROLLER BALL BEARING 6201-2RS ECCENTRIC SHAFT SET SCREW M6-1 X 12 GIB WEDGE DOG 208 209 210 211 212 213 214 LOCK BAR KNOB M12-1.75,7-LOBE, D72 EXTENSION WING LOCK WASHER 8MM FLAT WASHER 8MM HEX BOLT M8-1.25 X 30 SET SCREW M8-1.
Columns 318 313 313 305 311 311 313 316 309 315 314 313 317 311 308 305 312 302 329 305 320 320 310 332 301 331 306 307 329 319 323 327 321 322 326 324 325 306 307 319 321 303 304 328 333 REF PART # DESCRIPTION REF PART # DESCRIPTION 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 BASE HEX BOLT M12-1.75 X 60 HEX NUT M12-1.75 FLAT WASHER 12MM COLUMN SECONDARY BALL BEARING 6202-2RS INT RETAINING RING 35MM COLUMN PRIMARY INT RETAINING RING 38MM SET SCREW M10-1.
Gearbox 424 423 418 439 416 426 425 420 427 430 417 438 434 419 435 406 413 432 413 412 414 415 409 409 433 429 407 402 431 430 405 403 404 437 436 421 422 428 402 401 440 441 410 443 408 411 442 REF PART # DESCRIPTION REF PART # DESCRIPTION 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 GEARBOX COVER CAP SCREW M6-1 X 25 COLUMN SPROCKET FLAT WASHER 8MM HEX BOLT M8-1.25 X 16 CHAIN 06B-1 51 LINKS KNOB M10-1.
Stand 550-1 550-2 550-4 572 550-5 550-3 572 550-6 574 578 573 572 561 573 559 579 562 560 560 576 575 566 563569 568 572 575 573 573 579 551 517-8 517-2 517-9 517-7 517-3 517-6 517-4 550 502 565 558 571 570 517-5 517-1 576 577 520 519 517 518 515 503 510 501 516 513 505 504 509 522 517-9 506 512 514 519 521 557 507 556 524 527 526 525 508 523 510 511 555 528 554 529 529-1 529-2 529-14 529-13 529-3 529-4 529-12 529-5 529-6 529-8 529-7 529-10 529-11 529-9 Mode
Stand Parts List REF PART # DESCRIPTION 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 517-1 517-2 517-3 517-4 517-5 517-6 517-7 517-8 517-9 518 519 520 521 522 523 524 525 526 527 528 529 529-1 529-2 529-3 529-4 STAND ASSEMBLY CABINET COVER REAR FLAT HD CAP SCR M6-1 X 20 MOTOR MOUNT PLATE SET SCREW M6-1 X 12 CONNECTING ROD SET SCREW M8-1.25 X 12 CONNECTING ROD HEX BOLT M10-1.5 X 80 FLAT WASHER 10MM HEX NUT M10-1.5 LOCK COLLAR SET SCREW M6-1 X 8 ADJUSTMENT BOLT M12-1.
Labels & Cosmetics (Front, Right) POWER START 602 STOP CHECK OIL LEVEL BEFORE USING! WARNING! INJURY HAZARD! To reduce risk of shortand long-term injury, wear safety glasses, hearing protection, and a respirator when using this machine. WARNING! To reduce risk of death or serious injury, read manual BEFORE using machine. To get a new manual, call (800) 523-4777 or go to www.grizzly.com. INJURY/SHOCK HAZARD! Disconnect power before adjustments, maintenance, or service.
Labels & Cosmetics (Top, Left) 613 MODEL G0454ZX 20" PLANER WITH SPIRAL CUTTERHEAD Specifications Motor: 5 HP, 220V, 1-Ph, 60 Hz Full-Load Current Rating: 22A Cutterhead: 4 Spirals, 98 Inserts Cutterhead Speed: 4902 RPM Cuts Per Minute: 20,000 Feed Rate: 15, 20 FPM Maximum Width of Cut: 20" Maximum Depth of Cut: 1/8" Minimum Stock Thickness: 3/16" Maximum Stock Thickness: 8" Minimum Stock Length: 8" Replacement Inserts: H7319 Weight: 812 lbs. Date S/N Mfd.
WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
