We Power Your World! GPW2600 GAS PRESSURE WASHER MANUAL Green-Power America, LLC
GPW2600 GAS PRESSURE WASHER Products Service Information Green-Power America LLC thanks you for choosing a Green-Power America LLC product. Please register your product within 10 days of purchase to ensure that you receive optimal service. Always keep copy of your original receipt. By registering your product, you are protected: 1. You have a record of the product purchase, 2. Customer Service can Better serve you on Warranty related issues 3.
GPW2600 GAS PRESSURE WASHER CONTENTS SPECIFITIONS .................................................................................................................... 4 SAFTY INSTRUCTION .....................................................................................................5-8 INTRODUCTION .................................................................................................................. 9 PART LIST ...............................................................................
GPW2600 GAS PRESSURE WASHER 1, SPECIFITIONS 4 Model Number GPW2600 Maximum Pressure 2600 psi Rated Pressure 2000 psi Rated volume 2.0gpm Minimum Inlet Pressure 30 psi Maximum Inlet Pressure 100 psi Pump Heavy-duty maintenance-free axial cam Thermal Relief Valve Included Minimum Temperature of Pumped Water Maximum Temperature of Pumped Water 41°F(5°C) 140°F(60°C) Inlet & Discharge Ports 3/4" (19 mm) standard garden hose connector High Pressure Hose Length 25' (7.
GPW2600 GAS PRESSURE WASHER 2, SAFETY INSTRUCTIONS WARNING To reduce the risk of serious injury, read all instructions and precautions before operating this machine. SYMBOL MEANINGS: TOXIC This symbol warns you of possible toxic gases which can be harmful to your health or deadly if you are exposed to them. FLAMMABLE AND COMBUSTABLE MATERIALS This symbol warns of materials/gases which are present and extremely flammable. When you see this symbol, be very cautious not to ignite the material/gases.
GPW2600 GAS PRESSURE WASHER INADEQUATE VENTILATION • Materials placed against or near the pressure washer or operating in areas where the temperature exceeds 40°C ambient (such as storage rooms or garages) can interfere with its proper ventilation features causing overheating and possible ignition of the materials or buildings. • Operate pressure washer in a clean, dry, well-ventilated area a minimum of 4’ (1.2 m) from any building, object or wall. DO NOT OPERATE UNIT INDOORS OR IN ANY CONFINED AREA.
GPW2600 GAS PRESSURE WASHER ENGINE AND MUFFLER MAY BE HOT • Place the pressure washer in an appropriate location, away from children and pedestrians. • Avoid placing any flammable materials near the exhaust outlet during operation or shortly thereafter. • Keep a 4’ (1.2 m) clearance from buildings or other equipment around the pressure washer to prevent overheating. • WARNING - The engine muffler will be very hot during and after use, avoid touching the engine or muffler while they are still hot.
GPW2600 GAS PRESSURE WASHER PREVENT ACCIDENTAL WATER SPRAY • To prevent accidental water spray, the wand trigger should be placed in the locked position when not in use. KEEP HANDS AWAY • Keep hands and other body parts away from high pressure water stream as water pressure will cause severe bodily harm. SAFETY GLASSES • Always wear safety glasses while operating. DETERGENTS • Only use recommended detergents for pressure washers.
GPW2600 GAS PRESSURE WASHER PREVENT PUMP DAMAGE • Do not run the pressure washer engine for more than 5 minutes without pressing the wand trigger or damage to the pump may result. • Never let the machine run unless connected to the water supply. Ensure water supply is running water through the pressure washer before attempting to start engine. • Never run caustic fluids or acid through this machine.
GPW2600 GAS PRESSURE WASHER 3, INTRODUCTION 10 Ref. Description Ref.
GPW2600 GAS PRESSURE WASHER 4, PART LIST Handle *1 Frame *1 Pressure hose *1 Gun *1 Wand *1 Gun holster *1 Hose hook *1 Wheel *2 Knob*2 Others: Manual *1；Nozzle cleaner*1；Spark plug wrench *1；O-ring*2 (1for pressure hose，1for spray gun). WARNING! Before attempting to start pressure washer, ensure you complete the following important steps. 1) Fill gasoline tank with Unleaded Gasoline. This is a 4-cycle engine with separate reservoirs for gas and oil.
GPW2600 GAS PRESSURE WASHER 3) Ensure both the pressure hose and garden hose have been correctly attached to the pressure washer pump. Ensure the water tap is on and water is running through the hose before attempting to start engine.
GPW2600 GAS PRESSURE WASHER 5, ASSEMBLY INSTRUCTIONS 1. Lift the frame with one hand and attach one of the wheels by pressing the wheel’s pin and inserting the wheel shaft into the main frame. Align the pin with the hole on the frame (A) until it snaps in. Repeat for the opposite side. 4. Attach the hose hook to the back of handle assembly until it slides into place. 2. Position handle assembly and main frame and connect them with square neck bolt, then fasten with the knob.
GPW2600 GAS PRESSURE WASHER 6, PREPARATION 1. OIL LEVEL WARNING! Pressure washer has no oil currently in crankcase! Operating the unit without the correct amount of oil will damage the engine. Always check the oil level before starting the engine, make sure the pressure washer is on a level surface before checking oil level. Check the oil level： 1) Turn the oil gauge dipstick counter clockwise; remove it and clean it with a clean cloth.
GPW2600 GAS PRESSURE WASHER 1) If it is necessary to add fuel, first make sure the engine is OFF, and then remove the fuel cap by turning it counter clockwise. 2) When refueling, make sure the fuel filter is in place and keep in mind all safety precautions. 3) Use clean unleaded gasoline with a minimum of 87 octane. DO NOT use old gas. DO NOT mix oil with gasoline. Fuel tank capacity: 2.7L.. 3.
GPW2600 GAS PRESSURE WASHER 7, OPERATING INSTRUCTION 1.
GPW2600 GAS PRESSURE WASHER ➢ Open water source Supply Water ➢ Start engine WARNING！ Make sure to check the oil level and fuel level to prevent engine damage.
GPW2600 GAS PRESSURE WASHER Step #2 Step #6 Step #3 Step #4 Step #5 Step #1 Step #1：Turn the engine switch into “ON” position. Step #2：Locate choke lever to “CLOSE” position. Step #3：Turn the fuel valve into “ON” position. Step #4：Put the throttle lever to the “FAST” position. Step #5：Locate recoil cord and pull slowly until resistance is felt. At this point, pull rapidly to start engine. Step #6：After engine starting, locate choke lever to “OPEN” position.
GPW2600 GAS PRESSURE WASHER NOTICE：When the environment temperature is higher such as summer, or engine is in a hot state, choke valve should be switched to "ON" or intermediate position, then start the engine. 2. INSTRUCTIONS FOR USE ➢ Cleaning operation Position the tip of the wand 6-8” (15-20 cm) away from the surface to clean at a 45°angle. ➢ Nozzles This pressure washer comes with 5 different pattern of nozzles. RED 0°：Thin and powerful stream of water for difficult stains and debris removal.
GPW2600 GAS PRESSURE WASHER This engine comes with a throttle lever. The pressure can be adjusted by changing the speed of engine. Turning the throttle lever to the left can increase the speed to get more pressure. Turning the throttle lever to the right can decrease the speed to get less pressure. WARNING! When moving the engine throttle to the minimum (rightmost), the output power of engine is low. Please don’t operate the machine, if not, the machine will be flameout stop due to low engine output power.
GPW2600 GAS PRESSURE WASHER WARNING! Some cleaning jobs can be completed by using only water, but for most, it is advantageous to use a detergent to penetrate and remove the dirt more effectively. When using pressure washer approved detergent, make sure the surface to clean is dry. Wetting the surface first is not recommended; it will dilute the detergent and will reduce the cleaning effectiveness.
GPW2600 GAS PRESSURE WASHER 8, TROUBLESHOOTING PROBLEM Engine Engine doesn’t start or is difficult to start SOLUTION Ensure the switch is in ON (I) position No fuel Fill the fuel tank with regular gasoline Low oil shut down sensor tripped to protect engine (not applicable to 2600 psi pressure washer) Add oil until it reaches minimum level on dip stick Excess water pressure in pump or hose Release water pressure by squeezing trigger on gun Choke lever not in right position 1.
GPW2600 GAS PRESSURE WASHER PROBLEM Water supply faucet closed Turn on faucet. Ensure there are no kinks or blockage in hose Water supply pressure is low Ensure faucet is fully opened. Check to make sure water supply is a minimum 30 psi, 4 GPM Inlet water filter is clogged Clean the water filter.
GPW2600 GAS PRESSURE WASHER 9, MAINTENANCE ➢ WATER INLET FILTER: This pressure washer is equipped with a water inlet filter. This water filter must be kept clean at all times or else it will restrict the water flow to the pressure washer and may damage the pump. Remove the quick connect coupling from the water inlet, then remove and clean water filter. DO NOT operate this pressure washer without the water inlet filter in place as deposits could build up internally and affect the functioning of the unit.
GPW2600 GAS PRESSURE WASHER ➢ CLEANING CARBURETOR 1) Screw down the bolt on the bottom of carburetor with wrench. 2) Push the float up four to five times, then clean sediment cup with gas. 3) Put the sediment cup back. *** Be careful not to miss the O ring. ➢INSPECTING SPARK PLUG The spark plug should be checked every 100 hours of operation or every year. ➢ REPLACING AND CLEANNING SPARK PLUG 1) Dismantle the spark plug wire by pulling it off the spark plug.
GPW2600 GAS PRESSURE WASHER 10, STROAGE ➢ FUEL STABILIZER FUEL STABILIZER 1) Add fuel stabilizer to fuel tank to minimize the formation of fuel gum deposits during storage. 2) Run engine at least 5 minutes after adding stabilizer to allow it to enter the FUEL TANK fuel system. NOTE: If a fuel stabilizer is not used, all gasoline must be drained from the tank and carburetor to prevent gum deposits from forming on these parts and causing possible malfunction of the engine.
GPW2600 GAS PRESSURE WASHER ➢ RUST PROTECTION 1) Pour approximately one teaspoon of Engine Oil engine oil through the spark plug hole and pull the recoil starter slowly until you feel increased pressure which indicates the Spark Plug piston is on its compression stroke and leave it in this position. This closes both the intake and exhaust valves to prevent the inside of the cylinder from rusting. 2) Cover the pressure washer and store it in a clean, well ventilated and dry place.
GPW2600 GAS PRESSURE WASHER 10. LIMITED WARRANTY Always keep your receipt as proof of purchase. We’re here to help! If you have any questions or comments, call our Toll-Free 1888-834-4218. Have your serial number ready. The serial number can be found on the back plate, located on the rear of the unit. This product has a Parts Replacement, Product Exchange and/or Repair Warranty only. NO REFUNDS will be provided. Please see stores for Product Exchange details.
GPW2600 GAS PRESSURE WASHER Distributed By: Green-Power America, LLC www.Green-PowerAmerica.com or www.G-PAmerica.
