Performance and Specifications

ManualsBrandsGree ManualsAir ConditionersPTAC Air Conditioner Cooling Area, Adjustable Air Direction

FIELD--INSTALLED ACCESSORIES (CONT.)

Condensate Drain Kit

Part No.: DRAIN--KIT--1PK

The drain kit may be attached to the exterior right or

left side of the wall sleeve for external draining or

mounted to the room side of the wall sleeve for

internal draining.

A 3 in. (152.4 mm) straight tube and 90˚ curved tube

are supplied to simplify any application (1/2 in. /

12.7 mm OD copper).

IMPORTANT: For internal drains installed

in the p lastic wall sleeve, the drain must be

installed on the flat area of the sleeve. It

cannot be installed in the wafer area.

A07748

Drain Kit

Replacement Filters

Part No.: GA-FILTER-2PK

The Gree E-TAC model replacement air filters come

in packages of two (2). The filters save

energy by

preventing the evaporator coils from

being plugged with dirt and lint. These economical

and sturdy filters are interchangeable and may be

washed, vacuumed, and reused.

Replacement FIlters

Baffle Kit

Part No.: BAFFLE--KIT--1PK

Baffle Kit

This universal drain kit may be used internally or

externally to route condensate to a drainage system. It

can be field-installed on any Gree wall sleeve.

Although Gree units are designed to dissipate all the

condensate generated during normal cooling, there

may be times when abnormal conditions cause more

condensate than the unit can dissipate. If condensate

that drips from the wall sleeve is objectionable, this

internal/external drain kit should be installed.

The accessory baffle kit ensures a good seal between

the unit and the exterior grille to prevent air recircula-

tion, which can cause system failure.

The accessory baffle kit is required for applications

using unauthorized exterior grille.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW

CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC

components

• Less sensitivity to building orientation (sun,

wind, shade)

• Optional architectural grille to permit custom

exterior appearance

I nitial Cost Savings for the Buildin

g Owner

• N

o expensive component HVAC system

purchase

• No equipment room or maintenance

engineering staff

• Two--part delivery to minimize on--site

damage

• Weather--protected wall sleeve that goes in

place during construction; chassis that slides

in place after construction

• No seasonal changeover required for cooling

or heating -- units are self--contained comfort

systems

Lower Operating Costs and Reliable Comfort

for The Occupant

• Heat pump models offer substantial savings

over models with conventional electric

resistance heaters

• Individual units allow tenants to choose the

degree of comfort and operating economy.

• Rapi

d servicing reduces downtime: complete

chassis can be replaced in minutes without

disrupting other occupants.

• Each unit operates independently of other

units in the building. No dependency by

building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve,

your options include:

• Replace the existing wall sleeve with the

the polymer wall sleeve. See accessory sleeve

section for selecting the correct sleeve for

your application.

NOTE: in most cases, when replacing the

wall sleeve, the exterior grille must also be

replaced.

• Use an existing sleeve and exterior grille. The

Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve

tension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

E-TAC

Whether you are designing a new structure or

replacing packaged terminal air conditioning units in

an existing building, Gree E-TAC will meet your

needs.

The Gree E-TAC Packaged Terminal Air Conditioning

(E-TAC) unit is designed to meet the needs of the

architect, engineer, and contractor. For unit

installation, Gree’s expert support network will assist

in all applicable aspects of the construction project,

from preparing a budget to start-up.

The following major competitors’ wall

sleeves/grilles: Carrier, GE, Amana,

Trane, Friedrich and Bryant, and NO

accessory retrofit kit is required.