User's Manual

ManualsBrandsGOOD WAY ManualsSmart HomeScene Button

Scene Button

User’s Manual

Introduction

The Scene Button is a wireless switch designed to control other associated

devices through the Z-Wave controller. After receiving the signals emitted

by the Scene Button, the Z-Wave controller can then give commands or

operate according to its own settings. Its great compatibility with Z-Wave

products makes it suitable for Z-Wave smart home gateway.

Different scene device actions can be triggered by clicking, double-clicking,

or holding the button. The Scene Button can be conveniently mounted on

any surface and in any position or location at home, e.g. beside the bed or

on the desk.

The Scene Button is also a security Z-Wave device and supports the Over-

The-Air (OTA) feature for the product’s firmware upgrade. If you want it to

be a security device that use secure/encrypted message to communicate in

a Z-Wave network, then a security enabled Z-Wave controller is needed.

Package Contents

 Scene Button x 1

 User Manual x 1

 3M Double-sided tape x 1

 Screw x 2

Command Class

Z-Wave Scene Button Command Class Supported

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

COMMAND_CLASS_SUPERVISION_V1

COMMAND_CLASS_BATTERY_V1

COMMAND_CLASS_WAKE_UP_V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

COMMAND_CLASS_SECURITY_V1

COMMAND_CLASS_SECURITY_2_V1

COMMAND_CLASS_VERSION_V3

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4

COMMAND_CLASS_ASSOCIATION_V2

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1

COMMAND_CLASS_POWERLEVEL_V1

COMMAND_CLASS_CENTRAL_SCENE_V2

COMMAND_CLASS_CONFIGURATION_V1

Security

COMMAND_CLASS_ASSOCIATION_V2

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1

COMMAND_CLASS_POWERLEVEL_V1

COMMAND_CLASS_ CENTRAL_SCENE_V2

COMMAND_CLASS_CONFIGURATION_V1

COMMAND_CLASS_BATTERY_V1

COMMAND_CLASS_WAKE_UP_V2

COMMAND_CLASS_VERSION_V3

COMMAND_CLASS_SUPERVISION_V1

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4

Scene Button Device Information

Basic Device Class: ROUTING_SLAVE

Generic Device Class: SENSOR_NOTIFICATION

Specific Device Class: NOTIFICATION_SENSOR

Detailed description of each Command Class

[COMMAND_CLASS_ZWAVEPLUS_INFO]

The Z-Wave Plus Info Get Command is used to get additional information

of the Z-Wave Plus device in question.

[COMMAND_CLASS_SUPERVISION]

The Supervision Command Class allows a sending node to request

application-level delivery confirmation from a receiving node. The delivery

confirmation includes relevant application-level status information in the

confirmation message. The Supervision Command Class MAY be used for

solitary commands such as Set and unsolicited Report commands.

The Supervision Command Class MUST NOT be used for session-like

command ﬂows such as Get←→Report command exchanges or ﬁrmware

update.

[COMMAND_CLASS_BATTERY]

The Battery Command Class is used to request and report battery levels for

a given device.

[COMMAND_CLASS_WAKE_UP]

The Wake Up Command Class version 2 enables read back of the Wake Up

Interval capabilities in a node.

The Z-Wave Scene Button wakes up by wake up timer or presses the

physical button once, it will send Wakeup Notification Command to the

node ID that requires to be reported and stay awake for 10 seconds, if no

WAKE_UP_NO_MORE_INFORMATION command is received.

[COMMAND_CLASS_TRANSPORT_SERVICE]

The Transport Service Command Class supports the transfer of datagrams

larger than the Z-Wave frame.

[COMMAND_CLASS_SECURITY]

The Security Command Class create the foundation for secure application

communication between nodes in a Z-Wave network. The security layer

provides confidentiality, authentication and replay attack robustness

through AES-128.

[COMMAND_CLASS_SECURITY_2]

The Security 2 Command Class is a framework for allowing nodes to

communicate securely in a Z-Wave network. The Security 2 Command Class

provides backwards compatibility to nodes implementing the Security 0

Command Class. Security 2 Command Class also defines a new

encapsulation format, new Security Classes and a new KEX Scheme 1, which

together offers a number of advantages over the Security 0 Command Class.

Security 2 Command Class is scalable and allows more KEX Schemes,

Security Classes and encapsulation formats to be introduced in the future

if necessary.

[COMMAND_CLASS_VERSION]

The Version Command Class, version 3 allows supporting nodes to

advertise capabilities related to the Version Command Class and optionally

provide a detailed list of information regarding implementation on the Z-

Wave chip.

[COMMAND_CLASS_FIRMWARE_UPDATE_MD]

The Firmware Update Meta Data Command Class may be used to transfer

a firmware image to a Z-Wave device.

[COMMAND_CLASS_ASSOCIATION]

The Association Command Class is used to manage associations to Node ID

destinations. A Node ID destination may be a simple device or the Root

Device of a Multi Channel device.

[COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION]

The Multi Channel Association Command Class is used to manage

associations to Multi Channel End Point destinations as well as to Node ID

destinations.

[COMMAND_CLASS_ASSOCIATION_GRP_INFO]

The Association Group Information (AGI) Command Class allows a node to

advertise the capabilities of each association group supported by a given

application resource. Controllers and installer tools SHOULD use AGI

information to support controller-assisted button-to-button association

and GUI-based drag-and-drop association in a plug-and-play fashion.

Centralized gateway-based deployments may create a single association

from the lifeline association group to a central management application.

Group

Name

Description

1 Lifeline Lifeline group, association with 5 nodes.

[COMMAND_CLASS_MANUFACTURER_SPECIFIC]

Manufacturer Specific Command Class, version 2 adds a set of commands

to communicate unique identification, e.g. the serial number, of the

product. Commands not mentioned here remain unchanged as specified

for Manufacturer Specific Command Class, Version 2.

[COMMAND_CLASS_DEVICE_RESET_LOCALLY]

The Device Reset Locally Command Class is used to notify central

controllers that a Z-Wave device is resetting its network specific

parameters.

[COMMAND_CLASS_POWERLEVEL]

The Powerlevel Command Class defines RF transmit power controlling

Commands useful when installing or testing a network. The Commands

makes it possible for supporting controllers to set/get the RF transmit

power level of a node and test specific links between nodes with a specific

RF transmit power level.

[COMMAND_CLASS_CENTRAL_SCENE]

The Central Scene Command Class is used to communicate central scene

activations to a central controller using the lifeline concept.

Product Overview

Product Installation

Battery Installation

1. Slide the battery cover on the bottom of the product to separate it from

the main body.

2. Insert 2 AAA alkaline batteries into the battery compartment and make

sure that the positive and negative polarity of the battery is correct.

3. Slide the battery cover back to the main body.

4. Lock the 2 screws into the screw holes to ensure that the battery cover

is tightly integrated with the main body.

Note:

The package contents do not contain alkaline batteries and must be

purchased by the user.

Scene Button Installation

1. Place the Scene Button on your desktop.

2. Using the double-sided tape: first peel one side of the tape and place

the sticky side onto the battery cover of the Scene Button. Then peel

the other side of the tape and attach it onto a proper location on the

wall.

Product Operation

Function

Operation

Inclusion

Put the Z

Wave Controller into inclusion mode,

and press the button three times in 1.5 seconds to

include the

device

Exclusion

Put the Z

Wave Controller into exclusion mode,

and press the button three times in 1.5 seconds to

exclude the

device

Reset

Remove the battery of the Scene Button first.

2. Power on the Scene Button by reinserting the

battery and operate step 3 within 5 seconds.

3. Press the button three times in 1.5 seconds and

press and hold the button for more than 5

seconds at the 3rd time.

4. The device is excluded and restores to factory

default setting, and the device will be restored

to the unpaired status.

Note: Please use this procedure only when the

network primary controller is missing or otherwise

inoperable.

Send action

to trigger a

scene

Button pressed 1 time

Button pressed 2 times

Button held down

Button released

LED Indicator

LED Signal Status

LED off

Scene

Button is not powered.

2. Scene Button is in standby

mode

Red blinking once every 2

seconds for 30 seconds

When

Scene

Button is powered

and has not been added to the Z-

Wave network.

Solid Red for 5 seconds

When

Scene

Button is powered

and has been added to the Z-Wave

network.

Red blinking 1 time Button pressed 1 time successfully.

Red blinking 2 times Button pressed 2 times successfully

Red blinking 3 times

Inclusion process success

2. Exclusion process success

3. Parameter setting success

Button held down

successfully

Red blinking 6 times Low battery

Product Specification

Item Description

Power Supply DC 3V, AAA Alkaline Battery x 2

RF Protocol Z-Wave

RF Frequency

EU:868.4

MHz

US:908.40 MHz

JP: 922.50 MHz

KR: 920.9MHz

Data Rate 9.6kbps/40kbps/100kbps

Operation Range 100 feet (About 30M)

LED Indicator RED

Button

1 (Inclusion/

Exclusion/

rigger

Reset)

Waterproof Level IPX4

Operation Temperature -10℃ ~ 40℃

Regulatory Approvals CE/ FCC/ TELEC / Z-Wave® Plus

Dimensions (L*W*H) 80 x 80 x 40.5 mm

*Specification is subjective to change without prior notice.

Regulatory Compliance

CE Caution

Electromagnetic compatibility and Radio spectrum Matters (ERM); Short

Range Devices (SRD); Radio equipment to be used in the 25 MHz to 1,000

MHz frequency range with power levels ranging up to 500 mW; Part 2:

Harmonized EN covering essential requirements under article 3.2 of the

R&TTE Directive.

FCC Caution

This device complies with Part 15 of the FCC rules standard. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party

responsible for compliance could void the authority to operate equipment.

This device and its antenna must not be co-located or operating in

conjunction with any other antenna or transmitter. This equipment

complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with

V1.0

Summary of content (2 pages)

PAGE 1
Scene Button User’s Manual V1.0 Introduction The Scene Button is a wireless switch designed to control other associated devices through the Z-Wave controller. After receiving the signals emitted by the Scene Button, the Z-Wave controller can then give commands or operate according to its own settings. Its great compatibility with Z-Wave products makes it suitable for Z-Wave smart home gateway. Different scene device actions can be triggered by clicking, double-clicking, or holding the button.
PAGE 2
minimum distance 20cm between the radiator & your body. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.