Installation and Operating Instructions Built in Cooktops Please note: This cooktop must be installed by an authorised installer. The enclosed installation check list must be completed and signed off by the installer with the installer’s Licence number recorded to activate the Warranty.
SAFETY PRECAUTIONS IMPORTANT! This booklet is a fundamental part of the appliance, it should be retained. Read all instructions carefully before using the appliance. This appliance is to be installed by a qualified technician in accordance with the gas installation code AS5601, SAA wiring rules, as well as the requirements of all local statutory and building authorities and regulations. This appliance is for domestic use only and has been designed for cooking and heating food.
COOKTOP IDENTIFICATION Warning: This appliance is designed to be built into a kitchen bench capable of withstanding the weight of the appliance during its use. ♦ The kitchen bench must be resistant to temperatures of at least 100°C. Check with the manufacturer of the bench material to be sure. No liability will be accepted for damage to bench materials that do not comply ♦ See the relative paragraph and drawings for correct installation.
LIGHTING THE GAS BURNERS Gas burners The flow of gas to the burners is regulated by the controls knobs. Depending on the model, the graphic symbols are printed on the knobs or the control panel (Fig. 10). The indicator symbols are: Valve closed, no gas flow Maximum capacity, maximum gas flow Minimum capacity, minimum gas flow Turning On and Off Each control knob is clearly marked with the burner that it controls.
USING THE GAS COOKTOP Pan supports (trivets) The trivets were designed to make the cooktop easy and safe to use. We recommend checking their exact position and stability on the cooktop before each use. Furthermore, check that the supporting rubbers are integral and correctly positioned. Small vessel support (Fig.8) Only use the auxiliary burner ring (the smallest) for vessels with a small diameter to prevent them from tipping and to maximise efficiency. WOK Burner stand (Fig.
Fixing the cooktop The cooktop is to be fixed to the bench as follows: 1. Place the sealing gasket supplied along the outside edge of the hole cut into the bench so that the ends of the strips are perfectly joined without overlapping. 2. Position the cooktop into the hole in the bench making sure it is centered. 3. Attach the cooktop to the bench with the supplied mounts as shown in fig. 16. 4. When the sealing gasket is correctly installed, it will protect the cooktop from intrusion of liquids.
CONVERSION TO DIFFERENT TYPES OF GAS Should the cooktop need to be converted to a gas different to the one it was intended for, the injectors have to be replaced. It there are no spare injectors supplied they can be obtained from Glem Gas Service. The injectors are to be installed according to the table on the underside of the cooktop. Injectors can be identified by the diameter expressed in hundredths of mm printed on the injector itself.
After rinsing, dry with soft cloth. Avoid spray cleaners directed onto the graphics and take care when wiping not to damage the printed graphics on the cooktop. Cast Iron Trivets Wipe the trivets with a damp cloth once they have cooled. Do not use cleaning agents or harsh detergents to clean and dry carefully to prevent spotting or marking. This is important. Burners The burners are made up of two pieces and can be removed and cleaned with suitable products.
DIAGRAMS Fig. 1 Fig. 2 2 2 1 1 3 3 4 4 Fig. 3 Fig. 4 2 3 5 4 1 3 2 1 4 4 3 5 2 1 2 Fig. 5 3 1 4 Fig.
Fig. 7 Fig. 7A 2 1 5 3 4 Fig. 8 Fig. 9 Fig. 11 Fig. 10 Fig. 13 Fig.
Fig. 14 Fig. 15 Fig. 16 Fig. 17 Fig.
Fig. 21 Fig.
GLEM GAS AUSTRALASIA PTY. LTD. PRODUCT WARRANTY Thank you for choosing a Glem Gas Appliance, the purchase of this appliance is an important investment in your home and so to protect your investment we urge you to complete the registration card attached, please return it immediately. IT IS A WARRANTY REQUIREMENT THAT PROOF OF PURCHASE BE PROVIDED PRIOR TO REQUESTING A SERVICE CALL. THIS WARRANTY SHALL NOT APPLY IF THE APPLIANCE WAS NOT INSTALLED BY A LICENSED TECHNICIAN AND PROOF IS NOT SUPPLIED.