90SL Shower Enclosure Installation Guide Nova 90° Round Slider Shower Enclosure
A C B D 5 mm I J x5 E F G H 6mm x5 K x2 L x1 x1 N M x2 4 mm O P x2 Q x2 R S T Included in your purchase Shipped in 5 separate boxes A B C D E F G H Return Panel Fixed Panel Slider Panel Slider Panel Edge Strip Slider Panel Weather Strip Fixed Panel Weather Strip Shower Rod Aluminum Floor Strip I J Slider Panel Handle O Fixed Panel Clips, Screws P & Wall Anchors Q K Fixed Panel Brackets R L Shower Rod Brackets, Screws S & Wall Anchors T M Return Panel Shower Rod Bracket N Slide
Thank you for your purchase. If for any reason you are having trouble with installation, or if the size of the product does not fit your designated space, please contact Glass Warehouse directly and do not return this product to place of purchase. We will be able to exchange the panels or parts to suit your opening. Glass Warehouse takes pride in providing quality products and customer service. We want to ensure your happiness with your purchase for years to come.
Installation Guide 1⁄8" A B C D E ¼" F G H I J K Tools required for install. A B C D E F Silicone and caulking gun Power drill Phillips head screwdriver Pencil ⅛" tile drill bit ¼" tile drill bit G H I J K Hacksaw Utility knife Level Hammer Tape measure Note: Silicone is not provided and will need to be purchased separately. We recommend using a clear, mold resistant silicone which can be purchased at your local hardware store.
70" 8" These two measurements need to be the same W– 3 ½" from outer edge of glass width 01 02 Measure and mark the fixed panel location. Mark the three clip locations. Use a level and mark a line up the wall and along the floor. This is your center line for the clips. The two lines in the diagram above represent equal measurements. A 70" from the floor, up the vertical line. B 8" from the floor, up the vertical line.
03 04 Drill the holes for clips to fix to the wall and floor. Fix anchors and clips. Using a ¼" tile drill bit, drill the three marked holes on the wall and floor. Using a hammer, carefully insert the green wall and floor anchors. Trim any excess from the plug hanging out of hole so your clips can sit flush to wall and floor. If the shower base is tiled, use the same ¼" tile drill bit to drill the third hole on the shower floor. If the shower base is fiberglass, use a ⅛" drill bit for the floor hole.
05 06 Set the Return Panel in place. Place Slider Panel inside shower. Place the ⅛" rubber block on the floor 3" from the wall. Place a 1⁄16" rubber block inside the floor clip. Rubber blocks are not required in the wall clips. Place Slider Panel inside the shower on cardboard to protect the bottom of door. Be sure to face handle holes toward Return Panel. This will make it easier for installation at later stage once Fixed Panel and bar has been set in place.
70" 8" Width of Return Panel minus 1/4" 07 08 Mark the threshold and Fixed Panel wall. Mark the holes to drill on Fixed Panel wall. Measure the width of your Return Panel minus 1/4" and mark it on the threshold. Draw a level line up the wall at this point where the Fixed Panel will be placed. You will need at least 2 5/8" threshold width from this line to the inside of the shower enclosure. Along the drawn level line, mark 8" and 70" from floor.
09 10 Drill the holes for Wall Clips. Install Fixed Panel Wall Clips. Using a 1/4" drill bit, drill holes and install the wall anchors. Trim excess from the wall anchors hanging out of hole with utility knife so your clips can sit flush to wall. Place Wall Clips over holes and drill screws into wall anchors to secure clips. Make sure these are securely tightened. Important: Installer can use a 1/8" tile drill bit to create pilot holes, but this is optional.
Measure width from wall to Return Panel 11 12 Set the Fixed Panel in place. Measure opening width. Measure the width of the Fixed Panel and place the 1/8" thick Rubber Blocks provided 3" in from each end where the glass panel will sit on the tile/threshold. Gently place the glass panel down on the Rubber Blocks and slide glass into the Wall Clips. Check to make sure the glass is level. If not, adjust by adding thinner 1/16" Rubber Blocks to the blocks already on floor.
Panel hole Saw here 1" Shower opening width 13 14 Measure and cut Shower Rod. Install the Return Panel Shower Rod Bracket. I mportant: You must cut rod at opposite end from the Fixed Panel brackets. Subtract 1" from the opening width measurement (step 12) and then measure out this distance on the Shower Rod. For example: If your opening measurement is 47" your rod length should be 46". Use a hacksaw and cut your Shower Rod to the correct length.
Fixed Panel 15 16 Install the Fixed Panel Brackets on Shower Rod. Level Shower Rod and mark hole to drill. Install the brackets on Shower Rod into the holes on the Fixed Panel. If the brackets do not line up perfectly with the holes in the glass, you can loosen the allen bolt on the bracket to adjust it side to side to suit the holes in the glass. Using a level, check Shower Rod is perfectly level from one wall to the Return Panel.
17 18 Drill hole for Shower Rod Bracket. Screw in flat fixing piece and Shower Rod Bracket. Using 1/4" drill bit, drill hole and install wall anchor. Trim excess from the wall anchor hanging out of hole with utility knife. On Fixed Panel side wall install only the round flat fixing piece unscrewed from Shower Rod Bracket with rest of bracket remaining on rod. This allows you to slide the rod into one whole bracket on the Return Panel and then screw remaining bracket on opposing wall.
19 20 Complete Shower Rod install. Set Fixed Panel into Floor Bracket and mark hole. Tighten Fixed Panel Brackets and tighten the screws on Shower Rod Brackets. Make sure both of the bottom corners of the Fixed Panel measure the same distance from the front of the threshold tile (or fiberglass pan). Check panel is level again. Loosen allen screw on bottom of Floor Bracket and rotate adjustable end which fits on Fixed Panel for either left or right installation. Mark hole to drill for Floor Bracket.
Slider Panel Slider Panel 21 22 Drill hole, install anchor and install Floor Bracket. Install Sliding Panel Handle. Using a 1/4" drill bit, drill hole and install anchor (if necessary). Trim excess from the anchor with utility knife. Fill this hole with a little bit of silicone to waterproof. Reinstall Floor Bracket, making sure that the plastic insert is in place inside Floor Backet. Screw Floor Bracket down to secure. Carefully install the Slider Panel Handle on the Sliding Panel.
Slider Panel 23 24 Install Sliding Panel Rollers. Install the Slider Panel. Carefully install the Slider Panel Rollers on the Slider Panel. Be sure that Slider Panel is sitting on folded cardboard to avoid cracking or chipping. Lift the door and slowly lower the rollers onto the shower rod. When lowering the panel be sure the bottom of Slider Panel slides into the floor bracket. Important: Gently slide door from side to side making sure it is not binding anywhere along the bottom.
Slider Panel 25 26 Level and adjust Slider Panel Rollers. Install the Roller Guides. If Slider Panel is not level when hung from Rollers you can use the Roller Adjustment Tool to level it up. Install Roller Guide clips on Slider Panel to prevent the door from being able to come off rollers. Make sure there's no more than a 1/16" gap between the guides and the Shower Rod. The Roller Guides need to be almost touching the Rod to insure that the sliding door is completely secure.
27 28 Adjust Slider Panel Stoppers. Install Aluminum Floor Strip and optional Cap. Important: Slide door gently when testing door stops so as not to damage the door or the fixed panel. Adjust location of Slider Stoppers on Shower Rod to ensure the Slider Panel does not touch the Return Panel and the Slider Panel Handle does not touch the Fixed Panel. Install Aluminum Floor Strip to prevent water leakage. Measure distance from Floor Bracket to Return Panel and cut Aluminum Floor Strip to fit.
29 30 Trim Rubber Blocks. Apply silicone to seal Panels. Trim the Rubber Blocks under the Fixed Panel and Return Panel with a utility knife so that they are flush with the glass panel resting on top of them. Apply silicone around the wall and floor surface of the Fixed Panel and Return Panel. You need to silicone both the inside and outside edges ensuring the gap between glass and tile is completely sealed.
31 Install Weather Strips. Once silicone has cured, you're done! Install the plastic weather strip on panels. The shortest Weather Strip goes on the edge of the Fixed Panel. The longest piece goes on the outer edge of the Slider Panel near the handle. The mid-length piece goes on the inside of the Slider Panel. Please register your warranty using the instructions on the back cover of this document.
Care & Maintenance EnduroShield makes cleaning easier and less frequent; however it is recommended that you continue to clean the surfaces regularly. Maintaining the Treated Surface Approved Cleaning Products For best results simply drying the glass with a squeegee or towel after each use will help keep the glass clean and reduce mineral spots forming.
Exclusive Limited Warranty Terms & Conditions. This warranty is effective as of JANUARY 1, 2019 on all Glass Warehouse product purchases PLEASE READ GLASS WAREHOUSE WARRANTY TERMS AND CONDITIONS BEFORE INSTALLING YOUR GLASS WAREHOUSE PRODUCT. BY USING THE PRODUCT, YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS Glass Warehouse offers the following warranty for its products and components thereof.
obligation shall be discharged upon tender of parts, replacement or repair of the product. Purchaser’s refusal to accept the tender terminates all warranty obligations and VOIDS THE WARRANTY. Cost of freight for returning products to Glass Warehouse for repairs or replacement under this limited warranty are the responsibility of the customer. Cost of freight associated with shipping of replacement product(s) or parts covered by this warranty is the responsibility of the original user.
Register Your Warranty Today! To activate your limited lifetime warranty, please email inquiries@glasswarehouse.us and provide us with: • • • • • Name Purchase Order Number Model Number Address Email address We will require this information within 30 days of purchase to complete the activation of your warranty. If you have any further questions you can also email us at this same address.