User’s Manual (November 2007)
TRADEMARKS The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. All other brand and product names are trademarks or registered trademarks of their respective owners. NOTE The information in this manual is subject to change without notice.
Table of Contents Preface ..................................................................................... vi Chapter 1 Getting Started...................................................1-1 Getting the Computer Running ............................................ 1-2 Unpacking ........................................................................ 1-2 Connecting to AC Power ................................................. 1-2 Opening the Cover ........................................................
Hot Keys .......................................................................... 2-8 Using the Touchpad ........................................................... 2-11 Configuring the Touchpad ............................................. 2-13 Using the Touchscreen (Optional) ..................................... 2-14 Using the Hard Disk Drive................................................. 2-16 Installing a Second Hard Disk Drive (Optional) ............ 2-16 Using the Optical Drive (Optional) ........
Chapter 4 Expanding Your Computer ...............................4-1 Connecting an External Monitor .......................................... 4-2 Connecting a Serial Device .................................................. 4-4 Connecting a USB Device.................................................... 4-6 Connecting an IEEE 1394 Device........................................ 4-7 Using Smart Cards (Optional).............................................. 4-8 Inserting and Removing a Smart Card ............
Chapter 7 Caring for the Computer ...................................7-1 Protecting the Computer....................................................... 7-2 Using the Windows Security Center ................................ 7-2 Using the Cable Lock....................................................... 7-4 Taking Care of the Computer............................................... 7-5 Location Guidelines ......................................................... 7-5 General Guidelines.........................
Appendix A Specifications ................................................... A-1 Appendix B Regulatory Information .................................... B-1 On the Use of the System .....................................................B-2 Class B Regulations .........................................................B-2 Safety Notices ..................................................................B-3 On the Use of the RF Device................................................
Preface This manual contains information that will help you operate the computer. It is divided into 8 chapters and 2 appendices. z Chapter 1, Getting Started, takes you through the process of setting up the computer and identifying its external components. z Chapter 2, Operating Your Computer, tells you how to use the computer’s components and features. z Chapter 3, Managing Power, provides information on power.
Notational Conventions Throughout this manual, the following conventions are used to distinguish elements of text. NOTE: identifies additional information that requires special attention. CAUTION: identifies important information that, if not followed, may result in loss of data or damage to the computer. Keyboard keys are shown in a bold typeset. For example: Press the Enter key to complete.
Chapter 1 CHAPTER Getting Started Congratulations on purchasing this rugged computer. This chapter first tells you step by step how to get the computer up and running. You will find instructions for these procedures: z Unpacking z Connecting to AC power z Opening and closing the cover z Turning on the computer z Turning off the computer Then, you will find a section briefly introducing the external components of the computer.
Getting the Computer Running This section guides you through the procedures for getting the computer ready for operation. Unpacking After unpacking the shipping carton, you should find these standard items: z Rugged computer z Accessories: − AC adapter − AC power cord − Touchscreen pen (depending on your model) Inspect all the items. If any item is damaged or missing, notify your dealer immediately.
3. Plug the female end of the AC power cord to the AC adapter and the male end to an electrical outlet (o). 4. Power is being supplied from the electrical outlet to the AC adapter and onto your computer. Now, you are ready to turn on the computer. 5. When the AC adapter is connected, it also charges the battery pack. The Battery Charge Indicator on the computer glows amber to indicate that charging is in progress. When the battery is fully ) glows green.
Opening the Cover CAUTION: Be gentle when opening and closing the cover. Opening it vigorously or slamming it shut could damage the computer. Open the top cover by pushing on the cover latch (n) and lifting up the cover (o). You can tilt the cover forward or backward for optimal viewing clarity. Turning On and Off the Computer Turning On 1. Make sure that the computer is connected to AC power or battery is fully charged.
2. Press the power button ( ). 3. Each time the computer is turned on, it performs a Power-On Self Test (POST), and the Windows operating system should start. Turning Off To turn off the computer power, use the “Shut Down” command of your operating system. NOTE: There are other ways you can stop the computer so that you will be back to where you left off when you next turn on the computer. (See “Stopping the Computer” in Chapter 2 for information.
Taking a Look at the Computer This section identifies the external components of the computer and briefly describes the function of each component. NOTE: Depending on the model you purchased, the appearance of your computer may not be exactly the same as those shown in this manual. Right-Side Components NOTE: You may need to open the covers to be able to see the right-side components.
Ref Component Description See Also o Mini IEEE 1394 Port Connects an IEEE 1394 device such as a scanner, printer, DVCAM, VCR, and more. P. 4-7 p Serves as the master control that turns the RF (radio frequency) On/Off wireless LAN radio, Bluetooth radio, on/off. Switch P. 2-28, 2-30 q Card Reader Accepts a MultiMediaCard (MMC), Secure Digital (SD), Memory Stick (MS) or Memory Stick PRO (MS PRO) card for removable storage media. P. 4-14 r s RJ-11 Connector Connects the telephone line. P.
Left-Side Components NOTE: You may need to open the covers to be able to see the left-side components. Ref Component Description n Battery Pack Supplies power to your computer when external power is not connected. o Media Bay Depending on your model, the media bay may contain any of the following: Combo Drive/ DVD Dual Drive/ Super Multi Drive Accepts a compact disc for installing or loading software, accessing data, and playing music/video.
Rear Components NOTE: You may need to open the covers to be able to see the rear components. Ref Component Description See Also n Power Connector Connects the AC adapter. o USB Port Connects a USB device, such as a USB flash disk, printer, digital camera, joystick, and more. p Expansion Bus Connector Connects to a Port Replicator. q VGA Connector Connects an external display monitor. P. 4-2 r Serial Connector Connects a serial mouse or serial communication device. P.
Front Components Ref Component Description n Top Cover Latch Locks the top cover. o Handle Getting Started See Also P. 1-4 Provides a convenient way to carry the computer anywhere.
Bottom Components Ref n Component Memory Slots Getting Started Description Inside are the memory slots for expanding the memory size of your computer. See Also P.
Top-open Components Ref n Component LCD Screen Getting Started Description Displays the output of the computer. May include the optional touchscreen feature. See Also P.
Ref o Component Description See Also Quick Buttons P1 Turns off/on the LCD display and LED indicators, or User customized program quick launch key. NOTE: The function of P1 quick button depends on your setting in BIOS Setup program under the Advanced menu (see chapter 5 for details). Enables/disables power saving when using battery power. P. 2-21 P. 6-3 P. 2-4 Lights green when power saving mode is ON. Enables/disables sunlight readable display. P.
Ref Component Description See Also t Microphone Receives sound and voice for the computer. u Keyboard Serves as the data input device of the computer. v Fingerprint Sensor Serves as the fingerprint verification, preventing unauthorized access to your computer. P. 2-35 w Stereo Speaker Sends out sound and voice from the computer. P. 2-23 Indicators Show the current status of the computer’s devices. Power Lights green when computer is on. P. 2-23 P. 2-6 P.
Where to Go from Here As your computer is ready for operation, you may want to do any of the following now: For this purpose... To know more about the computer... Do this... Go on to the next chapter. To install the operating system if your See the operating system manual. dealer has not already done so... To know more about the operating system... Read the operating system manual. To set a power-on password... Read the operating system manual.
Chapter 2 CHAPTER Operating Your Computer This chapter provides information about the use of the computer. If you are new to computers, reading this chapter will help you learn the operating basics. If you are already a computer user but are new to rugged computers, you may choose to read only the parts containing information unique to your computer.
Starting and Stopping the Computer There are a number of ways to start and stop the computer. Starting the Computer You always start the computer using the power button ( ). A computer starts up with an operating system (OS) existing on the storage device such as the hard disk. The computer will automatically load the OS after you turn it on. This process is called booting. NOTE: An operating system is the platform for all your software application programs to run on.
To stop in this mode... Hibernation Do this... To start up or resume again Depending on your settings in Windows, you can place the computer in Hibernation mode by: • Closing the display cover • Pressing the power button Press the power button. If you choose to stop in Sleep or Hibernation mode, you can return to where you left off the next time you start up the computer. (See “Power Management” in Chapter 3 for more information.
Using the Quick Buttons Located on top of the keyboard are five quick buttons: z LCD display and LED indicators quick button (P1) to turn off the LCD display and LED indicator, or User customized program quick launch key (P1) – see chapter 6 for more details. NOTE: The function of P1 quick button depends on your setting in BIOS Setup program under the Advanced menu (see chapter 5 for details). z Power saving quick button ( ) to enter into power saving mode when using battery power.
z Light sensor quick button ( ) for adjusting the LCD brightness automatically based on your computer’s surrounding lighting condition. Lights green when light sensor is enabled.
Using the Internal Keyboard Your keyboard has all the standard functions of a full-sized computer keyboard plus a Fn key added for specific functions. The standard functions of the keyboard can be further divided into four major categories: z Typewriter keys z Cursor-control keys z Numeric keys z Function keys Typewriter Keys Typewriter keys are similar to the keys on a typewriter. Several keys are added such as the Ctrl, Alt, Esc, and lock keys for special purposes.
Cursor-Control Keys NOTE: The word “cursor” refers to the indicator on the screen that lets you know exactly where on your screen anything you type will appear. It can take the form of a vertical or horizontal line, a block, or one of many other shapes.
Numeric keys facilitate entering of numbers and calculations. When Num Lock is on, the numeric keys are activated; meaning you can use these keys to enter numerals. NOTE: z When the numeric keypad is activated and you need to type the English letter in the keypad area, you can turn Num Lock off or you can press Fn and then the letter without turning Num Lock off. z Some software may not be able to use the numeric keypad on the computer. If so, use the numeric keypad on an external keyboard instead.
Key Description Switches the wireless LAN radio on and off. Switches the night vision feature on and off for viewing the display when using night vision goggles (optional). Decreases the sound volume. Increases the sound volume. Switches the display output to one of the following when external devices are connected. Upon booting the system with CRT: LCD CRT LCD & CRT NOTE: This function only applies to Plug & Play display devices. Decreases the LCD brightness. Increases the LCD brightness.
Key Description Serves as the sleep button that you can define with Windows’ Power Options. (See the “Power Management” in Chapter 3.) Switches the keyboard backlight on and off (option). Euro Symbol You can press the euro dollar sign on various keyboards. z To press the euro sign on a United States-International keyboard, hold down the Alt Gr key and press 5 (which has an euro sign on it).
Using the Touchpad CAUTION: Do not use a sharp object such as a pen on the touchpad. Doing so may damage the touchpad surface. NOTE: z Press Fn+F9 to toggle the touchpad on or off. z For optimal performance of the touchpad, keep your fingers and the pads clean and dry. When tapping on the pad, tap lightly. Do not use excessive force.
Here are some common terms that you should know when using the touchpad: Term Action Point Move your finger on the pad until the cursor points to the selection on the screen. Click Press and release the left button. –or– Tap gently anywhere on the pad. Double-click Press and release the left button twice in quick succession. –or– Tap twice on the pad rapidly. Drag and drop Press and hold the left button, then move your finger until you reach your destination (drag).
Configuring the Touchpad You may want to configure the touchpad to suit your needs. For example, if you are a left-handed user, you can swap the two buttons so that you can use the right button as the left button and vise versa. You can also change the size of the on-screen pointer, the speed of the pointer, and so on. To configure the touchpad, go to Control Panel Æ Hardware and Sounds Æ Mouse Properties.
Using the Touchscreen (Optional) NOTE: z Make sure the touchscreen driver has been installed properly. z Press Fn+F8 to toggle the touchscreen on or off. CAUTION: Do not use a sharp object such as a ballpoint pen or pencil on the touchscreen. Doing so may damage the touchscreen surface. Use your finger or the included touchscreen pen (option).
Here are some common terms that you should know when using the touchscreen: Term Action Click/Point Tap gently on the touchscreen. Double-click Tap twice on the touchscreen rapidly. Drag and drop Press lightly on the touchscreen and move your finger/ touchsreen pen until you reach your destination (drag). Finally, release your finger/touchscreen pen (drop) when you finish dragging your selection to the destination. The object will drop into the new location.
Using the Hard Disk Drive Your computer comes with a removable hard disk drive as drive C. A hard disk drive is a storage device with non-removable, rotating, magnetic storage platters inside it. It is where your operating system and application software programs are stored. Your hard disk drive is a 2.5-inch PATA (parallel ATA) / SATA (serial ATA) hard disk drive.
4. Be careful to observe the correct orientation and slide the hard disk drive bracket into the media bay until it reaches the end. 5. Close the media bay cover to secure the hard disk drive bracket. NOTE: To remove the second hard disk drive, press upward the hard drive release latch (n) and carefully pull on the ribbon strip (o) to remove the hard drive.
Using the Optical Drive (Optional) Your computer may come with an optical drive, usually configured as drive D. Depending on the model, your drive is one of the following: z Combo drive can work both as a DVD drive (reading DVD discs in addition to CDs, audio CDs and CD-R/-RW discs), and also as a CD recorder (writing to CD-R/-RW discs). z DVD Dual drive besides the Combo drive function, can write to DVD+R/+RW/-R/-RW discs.
Inserting and Removing a Disc Follow this procedure to insert or remove a disc: 1. Turn on the computer. 2. Open the media bay cover by sliding the release latch towards the left. 3. Press the eject button and the DVD tray will slide out partially. Gently pull on it until it is fully extended. 4. To insert a disc, place down the disc in the tray with its label facing up. Slightly press the center of the disc until it clicks into place.
6. Close the media bay cover. NOTE: In the unlikely event that you are unable to release the drive tray by pressing the eject button, you can manually release the disc. (See “Optical Drive Problems” in Chapter 8.
Using the Video Features The video subsystem of your computer features: z 13.
Using the Audio Features NOTE: If you experience interference while recording, try lowering the microphone recording volume. The audio subsystem of your computer features: z Azalia interface (high density audio codec) z 2-channel analog output z Built-in microphone (n) z External audio connectors (o) and z Set of speakers (p) Ways of playing and recording sound vary with the operating system used. See your operating system documentation or online help for specific information.
Connecting Audio Devices For higher audio quality, you can send or receive sound through external audio devices. NOTE: After connecting an external audio device, make sure that you specify the use of the correct audio device in Windows. z Audio Output Connector (green) can be connected to speakers, headphones, or earphone set. z Microphone Connector (pink) can be connected to an external microphone for recording voice or sound.
Using the Communication Features Using the Modem The internal 56 K fax/data modem allows you to use the telephone line to communicate with others by fax, email, or connect to an online service or bulletin board. To connect the telephone line to the modem, connect one end of the modem cable to the RJ-11 connector on the computer and the other end to the phone line. NOTE: z When using the communication software, you may have to disable power management. z Set the COM port of the modem to COM3.
Using the LAN The internal 10/100/1000Base-T LAN (Local Area Network) module allows you to connect your computer to a network. It supports data transfer rate up to 1000 Mbps. To connect the network cable to the LAN module, connect one end of the LAN cable to the RJ-45 connector on the computer and the other end to the network hub.
Using the Wireless LAN Depending on your model, an internal mini PCI-E wireless LAN (WLAN) card may have been pre-installed by your computer manufacturer at the factory. This card allows you to access corporate networks or the Internet in a wireless environment. The WLAN features include: z Access Point (Infrastructure) mode support z WEP (Wired Equivalent Privacy) 64/128-bit data encryption z IEEE 802.
Turning Off/On the WLAN Radio NOTE: The FAA (Federal Aviation Agency) has deemed it unsafe to operate wireless devices in aircraft as this may interfere with flight safety. Remember to turn off wireless LAN when using your computer in the airplane. To turn on the WLAN radio: 1. Make sure that the RF switch is at the ON position. 2. Press Fn+F1 to turn on the WLAN radio (see “Hot Keys” in Chapter 2), indicated by the WLAN indicator ( on.
3. If any wireless network is detected, the following window appears on screen. Click the Show drop down menu and select Wireless. 4. Select a wireless network to connect to by clicking a selection, then click Connect. 5. Depending on the settings, you may be asked to enter a WEP key (refer to your Windows online help for more information on setting a wireless network connection).
Using the Bluetooth® Feature Depending on your model, your computer may incorporate the Bluetooth capability for short-range (about 10 meters) wireless communications between devices without requiring a cable connection. With Bluetooth wireless technology, data can be transmitted through walls, pockets and briefcases as long as two devices are within range. Turning On and Off the Bluetooth Feature 1. Make sure that the RF switch is at the ON position. 2.
3. The following appears onscreen. To turn on the Bluetooth feature, click the Bluetooth quick button. The Bluetooth indicator ( ) will glow in green. By default, your computer is in the general discoverable and pairable mode after the Bluetooth feature is turned on. 4. To turn off the Bluetooth feature, click the Bluetooth quick button again. The status of the Bluetooth connection is indicated by the Bluetooth icon located in the system tray in the lower-right part of the screen.
2. Right-click the icon, and then click Add New Connection. 3. The Add New Connection Wizard window appears. Select Express Mode (Recommended), and then click Next.
4. Select the device to connect to and click Next. 5. Depending on the type of Bluetooth device that you want to connect to, you will need to enter the pertinent information. Sending a File 1. Make sure that the target Bluetooth device is turned on, discoverable and within close range. (See the documentation that came with the Bluetooth device.) 2. Right-click the Operating Your Computer icon, and then click Wireless File Transfer.
3. In the Wireless File Transfer window, click Add to browse for the file to send. 4. Click the target device from the list, and then click Send to start the transfer procedure.
Using the Fingerprint Sensor To start using the fingerprint sensor: 1. Locate and slide open the fingerprint sensor cover.
2. Go to Start menu Æ Programs Æ Protector Suite QL Æ Control Center. The following screen appears. The computer features the Fingerprint Control Center utility for enrolling your fingers for added security.
Enrolling Fingerprints To start enrolling your fingerprint(s): 1. Click Fingerprints on the main menu. 2. Then click Initialize.
3. The following screen appears. Read carefully the contents of the Welcome screen and then click Next to continue. 4. Follow the onscreen instructions to complete enrolling your fingerprint(s).
Changing the Settings To change the settings of your fingerprint software: 1. Click Settings on the main screen. 2. Then click System Settings.
3. The following screen appears. Proceed to make the necessary settings to your fingerprint software. 4. Click OK after you have finished with your settings.
Chapter 3 CHAPTER Managing Power Your computer operates either on external AC power or on internal battery power. This chapter tells you how you can effectively manage power. To maintain optimal battery performance, it is important that you use the battery in the proper way.
AC Adapter CAUTION: z The AC adapter is designed for use with your computer only. Connecting the AC adapter to another device can damage the adapter. z The AC power cord supplied with your computer is for use in the country where you purchased your computer. If you plan to go overseas with the computer, consult your dealer for the appropriate power cord. z When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer.
Battery Pack The battery pack is the internal power source for the computer. It is rechargeable using the AC adapter. The operating time of a fully charged battery pack depends on how you are using the computer. When your applications often access peripherals, you will experience a shorter operating time. NOTE: Care and maintenance information for the battery is provided in the “Battery Pack Guidelines” section in Chapter 7.
CAUTION: After the computer has been fully recharged, do not immediately disconnect and reconnect the AC adapter to charge it again. Doing so may damage the battery. NOTE: The battery level may automatically lessen due to the self-discharge process (0.21 % per day), even when the battery pack is fully charged (100 %). This happens no matter if the battery pack is installed in the computer.
By Operating System You can check the approximate battery level using the battery meter function of the operating system. To read the battery level in Windows, click the icon on the system tray. By Gas Gauge On the exterior side of the battery pack is a gas gauge for displaying the estimated battery charge.
To replace the battery pack, follow these steps: 1. Make sure that the computer is not turned on or connected to AC power. 2. Locate the battery compartment on the left side of the computer. 3. Open the compartment cover by sliding the release latch to the left (n) then upwards (o). 4. Pull on the ribbon strip to remove the battery pack. 5. Slide the new battery pack all the way into the slot.
2. Open the media bay cover by sliding the release latch towards the left. 3. Press upwards the optical drive release latch (n) and carefully pull on the ribbon strip (o) to remove the optical drive. 4. Slide the second battery pack all the way into the slot. Make sure to observe the correct orientation (the ribbon strip must face outward for future battery pack removal). 5. Close the media bay cover to secure the second battery pack.
NOTE: To remove the second battery pack, press upwards the battery release latch (n) and carefully pull on the ribbon strip (o) to remove the battery pack. On the exterior side of the second battery pack is a gas gauge for displaying the estimated battery charge. When the battery pack is not installed in the computer and you want to know the battery charge, you can press the switch with a pointed device to see the corresponding value of indicator segment that light green.
Battery Low Signals and Actions The battery icon changes appearance to display the current state of the battery so that you can see how much charge remains (Windows default setting). When the battery charge is above 25 % the battery icon is green. When the battery charge reaches 25 % a yellow triangle with an exclamation point (!) appears above the green battery icon. When the charge reaches the low battery level a red circle with a white “X” appears ) above the green icon.
Power Management Your computer supports ACPI (Advanced Configuration and Power Interface) for power management. The power management feature allows you to reduce the power consumption for energy saving. With an ACPI-compliant operating system such as Windows Vista, power supply to different computer components is controlled on an as-needed basis. This allows maximum power conservation and performance at the same time. In general, Windows’ power management works in this way: What... When...
Hibernation NOTE: Make sure that the hibernation feature is enabled in the “When I press the power button,” “When I press the sleep button,” and “When I close the lid” of the Power Options Æ System Settings Properties from the Control Panel Æ Mobile PC in Windows Vista. Hibernation is a very useful feature. People frequently open many applications when they use computers.
Power-Saving Tips Aside from enabling your computer’s power saving mode (see previous section), you can do your part to maximize the battery’s operating time by following these suggestions. z Press the power saving quick button ( saving mode when using battery power. z Do not disable Power Management. Choose a Windows power plan that saves power. A power plan is a collection of hardware and system settings that control how your computer manages power.
Chapter 4 CHAPTER Expanding Your Computer You can expand the capabilities of your computer by connecting other peripheral devices. When using a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter.
Connecting an External Monitor If you want the benefits of a larger display screen with higher resolution, you can connect an external display monitor to your computer. Follow this procedure to connect an external monitor: 1. Make sure that the computer is not turned on. 2. Slide the release latch towards the right to open the connector cover. 3. Plug the monitor’s D-type signal connector to the computer’s VGA connector. 4.
7. You can change display settings through your operating system. See your operating system documentation or online help for specific information. CAUTION: Do not disconnect the external monitor while the computer is in the Sleep mode or Hibernation mode. If no external monitor is connected when the computer resumes, the LCD might not display properly.
Connecting a Serial Device Your computer has two serial ports for connecting serial devices such as serial mouse or serial communication device (modem). Follow this procedure to connect a serial device: 1. Make sure the “Serial Port COM1/COM2” item is set properly in the BIOS Setup program. (See “Advanced Menu” in Chapter 5 for information.) 2. Make sure the computer is not turned on. 3. Slide the release latch towards the right to open the port cover. 4.
Connecting a USB Device Your computer has three USB ports for connecting USB devices, such as a digital camera, scanner, printer, modem, and mouse. The USB ports support transfer rates up to 12 MB/s for USB 1.1 devices and 480 MB/s for USB 2.0 devices. To connect a USB device, slide the release latch towards the right to open the port cover and then simply plug the device cable to one of the USB ports.
Connecting an IEEE 1394 Device Your computer has a mini IEEE 1394 port for connecting IEEE 1394 devices that include not only computer peripheral devices such as scanner, printer and high-quality CCD, but also consumer electronic equipment such as DVCAM and VCR. To connect an IEEE 1394 device, prepare an IEEE 1394 cable. Slide the release latch towards the right to open the connector cover.
Using Smart Cards (Optional) Depending on the model, your computer has a smart card slot for additional security feature, providing tamper-proof storage of user and account identity. A smart card is a type of plastic card embedded with a computer chip that stores and transacts data between you (user) and the computer. You need to install third-party smart card software to take advantage of the smart card feature. Inserting and Removing a Smart Card To insert a smart card: 1.
To remove a smart card: 1. Make sure that the third-party smart card software is not accessing the smart card. 2. Pull the card out of the slot.
Using PC Cards Depending on your model, your computer has one or two PC card slots which supports type II card and CardBus specifications. Inserting and Removing a PC Card NOTE: z Some PC cards require additional system resources. Before using such PC card, you may have to free other system resources for the PC card. z Although some PC cards can be inserted and removed without turning off the computer, you cannot remove or install PC cards during Sleep mode. To insert a PC card: 1.
To remove a PC card: icon found on the 4. Double-click on the Safely Remove Hardware Windows Vista taskbar and the Safely Remove Hardware window appears on screen. 5. Select (highlight) the PC card from the list to disable the card. 6. Push the eject button and the card will slide out slightly. 7. Pull the card out of the slot.
Using ExpressCards (Optional) Depending on the model, your computer has an ExpressCard slot. ExpressCard supports the PCI Express and USB 2.0 serial data interfaces (supporting speeds of up to 2.5 Gbps and 480 Mbps respectively), improving speed in data transfer while conserving power usage. ExpressCard Type The ExpressCard slot can accommodate a 54 mm (ExpressCard/54) or 34 mm (ExpressCard/34) wide ExpressCard.
2. Slide the ExpressCard, with its label facing up, all the way into the slot until the rear connectors click into place. 3. When a new card is seated, the computer will detect it and try to install the appropriate driver. Follow the on-screen instructions to complete the process. To remove an ExpressCard: icon found on the 1. Double-click on the Safely Remove Hardware Windows taskbar and the Safely Remove Hardware window appears on screen. 2.
Using the Card Reader NOTE: z If your hard disk is divided into several drives, make sure that all drives have been formatted before using the Card Reader. Otherwise, you may encounter problems when using the Card Reader. z You can use only storage cards. Your Card Reader does not support cards with I/O (input/output) functions such as a wireless network card or Bluetooth wireless card. Your computer has a Card Reader.
2. Align the card with its connector pointing to the slot and its label facing down. Slide the card into the slot until it reaches the end. 3. Windows will detect the card and assign it a drive name (typically E). To remove a storage card: 1. Double-click My Computer. 2. Right-click the drive with the card and select Eject. 3. Pull the card out of the slot.
Using the Port Replicator (Optional) A port replicator is available as an option. This device eliminates the hassles of having you connect and disconnect the various cables when carrying your computer around and allows a variety of peripherals to be connected including a headphone or microphone, etc. The port replicator connects to the expansion bus connector at the rear of your computer. 1. Slide open the expansion bus connector cover. 2. Connect your port replicator to the expansion bus connector ( ).
System Memory Upgrade You can upgrade your computer by changing system memory to a maximum of 4 GB on the two 533/667 MHz DDRII SO-DIMM slots. CAUTION: RAM modules are extremely sensitive to static electricity. There are cases where static electricity generated by the human body has adversely affected such modules. When inserting or removing a RAM module, do not touch the terminals or internal components, insert objects other than the module, or allow foreign particles to enter.
4. To install the RAM module, match the module's notched part with the socket's projected part and firmly insert the module into the socket at a 20-degree angle. 5. Then push down until the retaining clips lock the module into position. CAUTION: If the RAM module is difficult to insert or difficult to push down, do not force it. Check once more to ensure that the module is positioned correctly. 6. Close the compartment cover and secure with six screws.
Chapter 5 CHAPTER Using BIOS Setup BIOS Setup Utility is a program for configuring the BIOS (Basic Input/ Output System) settings of the computer. BIOS is a layer of software, called firmware, that translates instructions from other layers of software into instructions that the computer hardware can understand. The BIOS settings are needed by your computer to identify the types of installed devices and establish special features. This chapter tells you how to use the BIOS Setup program.
When and How to Use BIOS Setup When to Use You need to run BIOS Setup Utility when: z You see an error message on the screen requesting you to run BIOS Setup Utility. z You want to restore the factory default settings. z You want to modify some specific settings according to the hardware. z You want to modify some specific settings to optimize the system performance. Starting BIOS Setup NOTE: z The BIOS Setup Utility screens shown in this chapter are for your reference only.
The BIOS Setup Utility screen can be divided into four areas: z On the top is the menu bar containing the titles of the available menus. Each menu title brings a specific menu. z The left column of the menu displays the menu items. z The right column of the menu provides more detailed information when a menu item is highlighted. z The bottom of the menu provides keyboard instructions for moving around and making selections.
Moving Around and Making Selections You must go through two or three levels to complete the setting for an item. In most cases, there are two levels: menu title and submenu. Use the keyboard to move around and make selections. Keyboard information can be found at the bottom of the screen. A brief description of keyboard usage is listed next: Key Function ←,→ Selects a menu title. ↑,↓ Selects an item or option. +/– Changes the value. Enter 1) Brings up the sub-menu when available.
Information Menu The Information menu contains the basic configuration information of the system.
Main Menu The Main menu contains the system date and time, as well as USB and wireless LAN settings of the system. System Time sets the system time. System Date sets the system date. Legacy USB Support enables or disables the system’s support for Legacy USB device in DOS mode.
Advanced Menu The Advanced menu contains the advanced settings as shown next. P1 Function allows you to specify the P1 quick button function. When set at Blackout the P1 quick button allows you to turn off the LCD backlight and LED indicator. When set at Quick Btn the P1 quick button functions as a user customized quick launch key. CD/DVD Auto Power Control allows you to enable the optical drive’s automatic power control when using battery power.
When set at Enhanced and connecting a SATA hard drive is set as Primary on SATA controller in Native mode. When connecting a PATA hard drive is set as Primary on PATA controller in Legacy mode. AHCI Configuration enables support for AHCI (Advanced Host Controller Interface) Native command queuing and Link Power Management. Requires Windows XP Service Pack 1 + IAA driver or newer operating system. This item will not appear if the above item “SATA HDD Mode” is set at Compatible.
Security Menu The Security menu contains the TPM (Trusted Platform Module) setting. TPM is a component on your computer’s mainboard that is specifically designed to enhance platform security above-and-beyond the capabilities of today’s software by providing a protected space for key operations and other security critical tasks. Using both hardware and software, TPM protects encryption and signature keys at their most vulnerable stages – operations when the keys are being used unencrypted in plain-text form.
TPM Support enables or disables TPM support (see chapter 6 for details). Current TPM State shows the current TPM state. Change TPM State allows you to select between No Change, Clear, Deactivate & Disable, and Enable & Activate.
Boot Menu The Boot menu sets the sequence of the devices to be searched for the operating system. The bootable devices will be automatically detected during POST and shown here, allowing you to set the sequence that the BIOS uses to look for a boot device from which to load the operating system. A brief description of keyboard usage is listed next: Key Function ↑,↓ Selects (highlight) a boot device. +, – Changes the boot sequence. 1 to 4 Loads the default boot sequence.
Exit Menu The Exit menu displays ways of exiting BIOS Setup Utility. After finishing with your settings, you must save and exit so that the changes can take effect. Exit Saving Changes saves the changes you have made and exits BIOS Setup Utility. Exit Discarding Changes exits BIOS Setup Utility without saving the changes you have made. Load Setup Defaults loads the factory default values for all the items. Discard Changes restores the previous values for all the items.
When and How to Use the System Recovery Feature When to Use You need to run System Recovery when: z Your computer does not start correctly. z Your Windows operating system does not start at all. z You want to restore the factory default Windows settings. Starting System Recovery To run System Recovery: 1. During system startup when the following screen appears, press Ctrl + Alt + F2 keys for four seconds or press Enter and select HDI Recovery when a small window appears on the screen.
2. The message This will help you reinstall Windows to the whole HDD to factory default. All data on HDD will be lost appears on the screen to ask if you want to access System Recovery. Type 1 to continue or type 0 to exit. 3. A warning message appears as follows: **************************************** You must accept the following terms before performing the recovery process: 1.
5. Your system will start the recovery process and Windows operating system will be re-installed to its default setting.
Chapter 6 CHAPTER Using the TPM and P1 Utility Your computer comes with an added security feature known as the TPM (Trusted Platform Module) – a component on your computer’s mainboard that is specifically designed to enhance platform security above-and-beyond the capabilities of today’s software by providing a protected space for key operations and other security critical tasks. Also, located on top of your keyboard is the P1 quick launch key.
Using TPM (Trusted Platform Module) TPM is a hardware-based security feature that can be used to create and manage computer-generated digital certificates. When combined with security software, the TPM enhances existing network and computer security by enabling features such as file protection capabilities and protected e-mail. NOTE: z Make sure you select Enable on the TPM Support item under the Security menu of your BIOS Setup (see chapter 5 for details).
P1 Quick Launch Key Utility If you select Quick Btn in BIOS Setup program on the P1 Function item under the Advanced menu (see chapter 5 for details), you can use the quick launch key utility that allows you to define the P1 quick launch key. ) and select To start the utility, right-click the GeTAC utility icon ( Quick Buttons Definition on the Windows system tray. The Quick Button Definition window appears as shown next.
Defining the buttons: The box in the window represents the user-definable button. To assign a program to a button, click the Open icon to pop up the Select a File to Open dialog box as shown next and select the desired program. Then, click Open to complete the process. The appropriate icon will then appear in the box. To launch the program, press the P1 quick launch key, or, if the Quick Button Definition window is open, click the box containing the icon.
Chapter 7 CHAPTER Caring for the Computer Taking good care of your computer will ensure a trouble-free operation and reduce the risk of damage to your computer.
Protecting the Computer To safeguard the integrity of your computer data as well as the computer itself, you can protect the computer in several ways as described in this section. Using the Windows Security Center Windows Security Center protects your computer against intrusion.
Windows Security Center alerts you to take action on the following security essentials: z Windows Firewall z Windows Update z Malware Protection (anti-virus, anti-spyware) z Others (Internet security, user account control) For detailed information on Windows Security Center, see Windows’ Help. Using the Cable Lock You can use a Kensington-type cable lock to protect your computer against theft. The cable lock is available in most computer stores.
Taking Care of the Computer Location Guidelines z For optimal performance, use the computer where the recommended temperature is between 0 °C (32 °F) and 55 °C (131 °F) – actual operating temperature depending on product specifications. z Avoid placing the computer in a location subject to high humidity, extreme temperatures, mechanical vibration, direct sunlight, or heavy dust. z Do not cover or block any ventilation openings on the computer.
Cleaning Guidelines z Never clean the computer with its power on. z Use a soft cloth moistened with water or a non-alkaline detergent to wipe the exterior of the computer. z Gently wipe the display with a soft, lint-free cloth. Do not use alcohol or detergent on the display. z Dust or grease on the touchpad can affect its sensitivity. Clean the pad by using adhesive tape to remove the dust and grease on its surface. Battery Pack Guidelines z Recharge the battery pack when it is nearly discharged.
z It is recommended that you charge the battery pack with the computer’s power off. z To maintain the battery pack’s operating efficiency, store it in a cool dark place removed from the computer and with 30 % ~ 40 % charge remaining. z Important guidelines when using the battery pack. When installing or removing the battery pack take note of the following: – avoid installing or removing the battery pack when the computer is in Sleep mode.
z Turn off the computer power when cleaning the display. Cleaning the display with the power on may cause improper operation. z Use the touchscreen within the intended area only. The display area and touchscreen operating area is the same. Using it beyond the allowed area may cause damage to the display and result in improper operation. z Do not use excessive force on the display. Avoid moving the computer while holding the display or twisting the display.
When Traveling z Before traveling with your computer, make a backup of your hard disk data into flash disks or other storage devices. As an added precaution, bring along an extra copy of your important data. z Make sure that the battery pack is fully charged. z Make sure that the computer is turned off and the top cover is securely closed. z Do not leave objects in between the keyboard and closed display. z Disconnect the AC adapter from the computer and take it with you.
Chapter 8 CHAPTER Troubleshooting Computer problems can be caused by hardware, software, or both. When you encounter any problem, it might be a typical problem that can easily be solved. This chapter tells you what actions to take when solving common computer problems.
Preliminary Checklist Here are helpful hints to follow before you take further actions when you encounter any problem: z Try to isolate which part of the computer is causing the problem. z Make sure that you turn on all peripheral devices before turning on the computer. z If an external device has a problem, make sure that the cable connections are correct and secure. z Make sure that the configuration information is properly set in the BIOS Setup program.
Solving Common Problems For easy reference, the problems are divided into these categories. Problem Type Go to Battery Problems P. 8-4 Bluetooth Wireless Transmission Problems P. 8-4 Display Problems P. 8-5 ExpressCard Problems P. 8-6 Hardware Device Problems P. 8-6 Hard Disk Drive Problems P. 8-7 Keyboard, Mouse, and Touchpad Problems P. 8-7 LAN Problems P. 8-8 WLAN Problems P. 8-8 Modem Problems P. 8-8 Optical Drive Problems P. 8-10 PC Card Problems P.
Battery Problems The battery does not charge (Battery Charge indicator does not light amber). z Make sure that the AC adapter is properly connected. z Make sure that the battery is not too hot or cold. Allow time for the battery pack to return to room temperature. z Make sure that the battery pack is installed correctly. z Make sure that the battery terminals are clean. The operating time of a fully charged battery becomes shorter.
z Make sure that both devices are compatible. Display Problems Nothing appears on the screen. z During operation, the screen may automatically turn off as a result of power management. Press any key to see if the screen comes back. z The brightness level might be too low. Increase brightness by pressing the Fn+F7 hot key. z The display output might be set to an external device.
ExpressCard Problems The ExpressCard does not work. z Make sure that the ExpressCard is correctly seated. z If the card requires an IRQ (Interrupt ReQuest), make sure that there is one available. The ExpressCard stops communicating properly. z The application may have been reset when the computer is turned off or in Sleep mode. Exit and restart the application. Hardware Device Problems The computer does not recognize a newly installed device.
The hard disk drive in-use indicator glows without blinking. z The data files stored on the hard disk drive may be fragmented. Use a tool such as Window’s Disk Defragmenter to defragment the files. Keyboard, Mouse, and Touchpad Problems The keyboard does not respond. z Try connecting an external keyboard. If it works, contact an authorized dealer, as the internal keyboard cable might be loose. The numeric keypad is disabled. z Make sure that the Num Lock is switched on.
WLAN Problems I cannot use the WLAN feature. z Make sure that the mini PCI-E WLAN card is correctly installed. z Make sure that the WLAN feature is turned on. Transmission quality is poor. z Your computer may be in an out-of-range situation. Move your computer closer to the Access Point or another WLAN device it is associated with. z Check if there is high interference around the environment and solve the problem as described next. Radio interference exists.
z If the operating radio channel is in poor quality, change the Access Point and all the wireless station(s) within the BSSID to another radio channel. z Your computer may be in an out-of-range situation. Move your computer closer to the Access Point it is associated with. z Make sure that your computer is configured with the same security option (encryption) to the Access Point. z Use the Web Manager/Telnet of the Access Point to check whether it is connected to the network.
z Make sure that the disc is not dirty. Clean the disc with a disc cleaning kit, available in most computer stores. z Make sure that the computer supports the disc or the files contained. You cannot eject a disc. z The disc is not properly seated in the drive. Manually release the disc following the method described next: 1. Turn off the computer. 2. Open the media bay cover by sliding the release latch towards the left. 3.
z If the card requires an IRQ (Interrupt ReQuest), make sure that there is one available. The PC card stops communicating properly. z The application may have been reset when the computer is turned off or in Sleep mode. Exit and restart the application. Power Management Problems The computer does not enter Sleep or Hibernation mode automatically. z If you have a connection to another computer, the computer does not enter Sleep or Hibernation mode if the connection is actively in use.
Software Problems An application program does not work correctly. z Make sure that the software is correctly installed. z If an error message appears on the screen, consult the software program’s documentation for further information. z If you are sure the operation has stop, reset the computer. (See “Resetting the Computer” later in this chapter.) Sound Problems No sound is produced. z Make sure that the volume control is not set too low. z Make sure that the computer is not in Sleep mode.
Startup Problems When you turn on the computer, it does not respond and the Power Indicator does not light green. z If you are using an external AC power, make sure that the AC adapter is correctly and securely connected. If so, make sure that the electrical outlet works properly. z If you are using the battery power, make sure that the battery is not discharged. When you turn on the computer, it stops after POST. z Restart your computer. Other Problems The date/time is incorrect.
Resetting the Computer You may have to reset (reboot) your computer on some occasions when an error occurs and the program you are using hangs up. If the computer operation seems to hang up, first wait. It is possible that the computer is processing data. Periodically check the hard disk drive in-use indicator, if it flashes irregularly, the program may be accessing data and preventing you from using the keyboard.
Appendix A APPENDIX Specifications NOTE: Specifications are subject to change without any prior notice. Parts CPU Chipset NorthBridge SouthBridge Intel® ICH8M BIOS RAM (system) Display Audio Specifications Intel® Core™ 2 Duo Merom processor LV L7300/LV7500 800 MHz FSB (Front Side Bus), 1.4/1.6 GHz, 4 MB L2 cache thermal specifications 17 W Intel® GM965, dual channel support Panel 1 MB EEPROM, ACPI, fingerprint / smart card security, TPM Up to 4 GB DDRII 533/667 MHz, 2 × 200-pin SO-DIMM sockets 1.
Parts Storage device Optical drive Card slots I/O ports Modem LAN Wireless LAN Bluetooth wireless technology (option) GPS (option) Security Power Dimension (W×D) Weight Specifications Specifications Hard disk drive SATA interface, 2.5-inch diameter (9.
Appendix B APPENDIX Regulatory Information This appendix provides regulatory statements and safety notices on your computer. NOTE: Marking labels located on the exterior of your computer indicate the regulations that your model complies with. Please check the marking labels and refer to the corresponding statements in this appendix. Some notices apply to specific models only.
On the Use of the System Class B Regulations USA Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Canada Canadian Department of Communications Radio Interference Regulations Class B Compliance Notice This Class B digital apparatus meets all requirements of the Canada Interference-Causing equipment regulations. Cet appareil numérique de Classe B respecte toutes les exigences du Règlement Canadien sur le matériel brouileur.
ENGLISH CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions. DEUTSCH VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
About the Modem Caution z Never install telephone wiring during a lightning storm. z Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. z Never touch non-insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. z Use caution when installing or modifying telephone lines. z Avoid using the telephone function (other than a cordless type) during an electrical storm.
On the Use of the RF Device NOTE: The information in this section applies to models with the wireless LAN module. USA and Canada Safety Requirements and Notices IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
z The use of wireless devices in hospitals is restricted to the limits set forth by each hospital. Antenna use: z In order to comply with FCC RF exposure limits, low gain integrated antennas should be located at a minimum distance of 20 cm (8 inches) or more from the body of all persons.
EMC Requirements This device uses, generates and radiates radio frequency energy. The radio frequency energy produced by this device is well below the maximum exposure allowed by the Federal Communications Commission (FCC). This device complies with the limits for a Class B digital device pursuant to Part 15 subpart C of the FCC Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.
Canada Radio Frequency Interference Requirements To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Pour empêcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit être utilisé à l'intérieur et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal.
Greek To προϊόν αυτό πληροί τις προβλέψεις της Ευρωπαϊκής Οδηγίας 1999/5/EC. Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer 1999/5/EC. Italian Questo prodotto è conforme alla Direttiva Europea 1999/5/EC. Norwegian Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 1999/5/EC. Portuguese Este produto cumpre com as normas da Diretiva Européia 1999/5/EC. Spanish Este producto cumple con las normas del Directivo Europeo 1999/5/EC.
The European variant is intended for use throughout the European Economic Area. However, authorization for use is further restricted in particular countries or regions within countries, as follows: General European standards dictate maximum radiated transmit power of 100 mW Effective Isotropic Radiated Power (EIRP) and the frequency range 2400 – 2483.5 MHz. Belgium and the Netherlands In Belgium and the Netherlands, the product may not be used outdoors.
Departments in Which the Wireless LAN Module’s Maximum EIRP Not Shown in the Previous Table Frequency Ranges (MHz) Indoors Outdoors 2400 – 2446.5 10 mW Not permitted 2446.5 – 2483.5 100 mW 100 mW on private property with Ministry of Defense approval Turning Off the Wireless LAN Radio NOTE: Turning the wireless LAN radio off is not the same as disabling the wireless LAN card. It is not necessary to disable the card to meet the regulatory requirements.
电子信息产品有毒有害物质或元素名 称及含量标示 有毒有害物质或元素 项目 部件名称 铅 (Pb) 镉 (Cd) 汞 (Hg) 六价铬 (Cr+6) 多溴联苯 多溴二苯醚 (PBB) (PBDE) 1 金属机构件 X O O O O O 2 塑料机构件 O O O O O O 3 电路板组件 X X O O O O 4 液晶面板 X X X O O O 5 硬盘 X O O O O O 6 光驱 X O O O O O 7 键盘 X O O O O O 8 充电电池组件 X X O O O O 9 适配器 X X X O O O 10 电源线 X O O O O O 11 外部信号连接线 O O O O O O 12 钮扣电池 O O X O O O 13 风扇 X O O O O O 14 散热模块 (金属部分) X O O O O O 15 喇叭 X O O O
使用除外项目如下： 1. 铅使用于部件、装置的内部连接用高融点锡焊上（铅为 85wt% 以上的有铅锡焊）。 2. 电子陶瓷部件（压电组件・陶瓷介质材料等）内的含铅量。 3. 电子部件的玻璃内的含铅量。 4. 两种以上元素组成之焊料，用于连接微处理器封装与针头且铅含 量超过 80wt% 并少于 85wt%。 5. 铅于覆晶集成电路封装内用于铸模与基板之电子接点之焊锡。 6. 于钢材、铝材、铜材中的含铅量。 7. 通孔盘状及平面数组陶瓷多层电容器焊料所含的铅。 8. 电子接点的电镀，其要求高可靠性，且没有替代性材料之镉。 9. 电池内的含铅量。 10. 电池内的含镉量。 11.
