ASSEMBLY INSTRUCTIONS NIGHT STAND ASSEMBLY REQUIREMENTS 50 MINUTES 1-Person Tools Required: Approximate Assembly (Not Provided) Assembly Time ® eo Thank you for purchasing our product Please refer ond use this assembly instruction to assemble the product. Contact our customer service department in case there are any missing or damage parts or hardware, Replacement parts are normally shipped within 2 or 3 days. We appreciate your business! Within 30 days from delivery date ASSEMBLY PREPARATION: 1.
ASSEMBLY INSTRUCTIONS NIGHT STAND HARDWARE LIST CSK SCREW CAM9499 CAM 3000 A | fw M3.5X 12MM & nL 15X12 a CSK SCREW CAMERA CAM 2000 8 fas M35 X 15MM $M 12130 4 PLASTICINE HANDLE CSK SCREW 2 | pum PY WITH SCREW M4 X 25MM (MARXISM{ IPC] SETS CSK SCREW DRAWER SLIDE CR D | fms M45 X 22MM 8 ||P 8 (350MM) 2 DRAWER SLIDE CL E | oom SCREW MAT X 38MM (350MM) 2 EURO SCREW DRAWER SUED DR Foot M6 X FMM aio) 2 WOOD DOWEL. DRAWER SIDE 20MM] (Assam) 2 : TABLE CORNER BRACKET WOOD DOWEL {HOLES) 4 (6X 35hM) [1.
PARTS LIST ASSEMBLY OVERVIEW PARTS LIST NO. PART NAME ary ||No.
INSTRUCTIONS FOR FITTING CAM-BOLT AND CAM-LOCK CAM-BOLT CAM-LOCK CAM-BOLT Insert Cam-bolt info the per-drifled hole. Use a Phillips Screwdriver En 5h to tighten until shoulder is snug and flushed with the panel, See frustrations below. Shoulder is flushed {on Shoulder Is above the panel. the same level) with the panel, CAM LOCK Align the arrow on the Hammerlock to the Cam bio (x head and insert the Com-ck.
STEP 1 en Apply a small amount of Glue {T} to the holes identified on each part below. Do SN 2S Insert Wood Dowel each designated holes on each respective parts. 2 Use a Mallet fo insert Wood Dowel, if necessary. & & STEP 2 Insert Carbolic {K) info the holes of parts shown below. Use a Phillips Screw driver fo tighten Cam-boils, Refer fo Page 4 on proper fastening of Cam-bolts.
STEP 3 Step 3A Use Screw [D} fo assembler Left & Right Drawers Sides Drawer Back {12} as shown. Use Phillips Screwdriver {not provided) fo drive Screw {D}. Step 3C Install Drawer Front {8 & 9} with Cam-bolts completed in Step 2. Check that wood dowels on Drawer Front. Use Cam-lock [M} to lock Carbonates on Drawer Front, Refer to Page 4 on proper fastening of Cam-lock. Step 38 Insert Drawer Bottom (13) via groove on 10,11 & 12 Step 3D Fasten Handle {MN} to Drawer Front with screw provided.
STEP 4 Position drawer with bottom-side up. Next place Drawer Slide DR {Q1) and DL {Q2) with roller end towards the Drawer Back {12]. Align the holes on {Q1} or {2} fo the pilot holes on Drawer Sides {10 & 11) and use Screw {A} to fasten. STEP § Step 5A Install Drawer Slide CL (P2) to Side Panel Left (1). Step 58 Install Drawer Side CR (P1) to Side Panel Right (2). To install (P1) or {P2}. first, use the drawing to orientate the placement of {P1) or (PZ). Second, identify the pilot holes for screws (F).
STEP 6 — Apply Glue (T) fo the holes between the Cam-bolls on Bottom Panel (4}. Next align and fit wood dowels on Front, Rear, Left & Right Bottom Rai a Panel the holes on Bottom Panel (4). STEP 7 Fit Wooden Leg (5) between panels (6) & {7) and use screw (E) to fasten Wooden Leg fo Bottom Panel {4}. Note: For the purpose of illustration, Bottom Panel is positioned flak-down.
STEP 8 — On Front, Rear, Left & Right Bottom Rail Panel {6 & 7), insert Cam-locks (L} and tum clock-wise to lock the Cam-bolts. ov? STEP 9 Affix § holes Table Corner Bracket {R] to Wooden Leg {5) using Screw (C).
STEP 10 Apply Glue (T} fo the holes between the Cam-bolts on Side Panel Eff (1). Next, align and insert Cam-boles on Side Panel Left (1} fo the holes on Top & Bottom Panels {3 & 4}. Firmly attach Side Panel Left. insert Cam docks {L} and tum clock-wise to lock the Cam-bolts. STEP 11 Insert Back Panel {14} into the grooves on Top Panel {3} & Bottom Panel (4).
STEP 12 Use the muse procedures in Step 10 fo install Side Panel Right {2}, STEP 13 Insert Drawers fo the Assembly. To insert drawers, position riflers {on the drawer slide on each side of the drawer] above the rollers on Side Panel Left & Right. Uft the Drawer Front slightly upward and slide the rollers on the drawer info the drawer slide.
STEP 14 EN Affix Back ply Stopper {3] to the Buck Panel using Screw (B}. ST Exe {5x8 dl Us STEP 15 CAUTION: FLEAS DO NOT FULLY OPEN DRAWERS SIMULTANEOUSLY AS IT WILL CAUSE THE NIGHT STAND TO FALL DOWN.
Thank you for purchasing our product! Please assemble the products with the guidance of this manual instruction. Contact our friendly customer service department with any comments or in case there is any missing or damaged parts or hardware. Replacements for missing or damaged parts or hardware are normally shipped within 2 to 3 days.