Instructions / Assembly

INSTALLATION INSTRUCTIONS FOR P1752-L
For Wall Sconce Fixture
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R
A V E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F U S I B L E S O U D O D I S J O N C T E U
ASSEMBLING THE FIXTURE (Fig.1)
1. Shut off power at the fuse box or circuit breaker box and remove
the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in a
clear area. Take care not to misplace any small parts necessary
for installation.
3. Remove screws (I), rubber washers (J) and cap nuts (E)
separating mounting plate (A) and parts (H, G, F).
4. Attach mounting plate (A) to the junction box with mounting
screws (D) (size:8-32*1/2"L) provided.
Note: The side of the mounting plate marked "GND" must face
out.
CONNECTION THE WIRES (Fig.2)
5. Connect the electrical wires as shown in Fig.2. Make sure that all
wire connectors are secured. If your junction box has a ground
wire (green or bare copper), connect the fixture’s ground wire to
it. Otherwise, connect the fixture’s ground wire directly to the
mounting plate (A) using the green screw (C) provided. Tuck the
wire connectors neatly into the junction box.
FINISHING THE INSTALLATION (Fig.1)
6. Thread the 2 mounting screws (B) into the mounting plate (A)
spaced the same distance apart as the holes in the fixture back
plate (F). (You can adjust the length of the screws if necessary.)
7. Align back plate (F) to screws (B) and secure with cap nuts (E).
8. Place the glass (G) with marked arrow on the topside into frame
(H), then secure frame (H) to back plate (F) with rubber washer
(J) and screws (I) onto back plate (F).
9. To prevent moisture from entering the junction box and causing a
short circuit, use clear caulking (i.e. Indoor/Outdoor silicone
sealant) to outline the outside of frame (H) where it meets the wall
leaving a space at bottom to allow moisture a means to escape
(Fig.3).
Your installation is now complete. Return power to the junction box and
test the fixture.
CAUTION /ATTENTION: When handling the fixture, do not apply
pressure to the LEDs. Hold the fixture by the base or back plate
only.
Replacing LED module (Fig.4)
The LED module can be replaced by a qualified electrician without
cutting of wire and without damage to any decorative element to which
the fixture is attached. See installation steps for more details (Fig.4)
Warning: Turn off power at the circuit breaker before
replacing LED module.
a. Loosen screws (I) and rubber washers (J) to remove frame (H)
and glass (G). (Fig.1)
b. To remove the fixture from the wall: loosen cap nuts (E).
Disconnect the wire connectors and place the fixture (F) on a
clear flat surface. (Fig.1)
c. Loosen screws (K) and remove protective case (L) from back
plate. Remove the waterproof silicon on the protective case (L),
loosen screws (M) to remove cap (N) and diffuser (O).
d. Loosen screws (S), rubber washers (R), screws (P) and wire
fastener (Q). Carefully remove LED module (T).
e. Reverse steps a-d for installing the new LED module.
Note: The LED module should be provided by a specified supplier.
IMPORTANT: Fixture should be installed by a qualified electrician to
ensure proper wiring and installation.
Dimmable with ELV and/or LED compatible wall dimmer
switches.
Fig. 2
Fig.1
Fig.3
Fig.4