User Guide

ManualsBrandsGenie ManualsBuilding SuppliesGenie SilentMax 1200 Garage Door Opener - ¾ HPC Power Plus DC Motor Belt Drive System - Includes 2 3-Button Remotes, Wall Console, Wireless Keypad, Motion Detector and Safe-T-Beams - Model 4042-TKH

Car2U

System

Programming for Genie

Setting the Car2U to Factory Default settings

The default setting for the Car2U system is:

• Button 1= Genie Manufactured Openers

• Button 2= LiftMaster

Manufactured Openers

• Button 3= Wayne Dalton

Manufactured Openers

1. Press and hold buttons 1 and 3 for twenty seconds or until all three LED’s begin to

flash.

2. Release both buttons. The Car2U system is now set to the Factory Default

settings.

To Change One of the Other Manufacturer’s Buttons to Genie

1. Press and hold buttons 1 and 3 for one second and release– all three LED’s will

light solid RED.

2. Press and hold the button (2 or 3) you want to change to Genie – the corresponding

LED will flash. While continuing to hold the button you want to change, press and

release button 1. Press and release button 1 again.

3. Release the button you were holding in step 2 and wait for the LED to stop flashing.

This button is now set for Genie.

Note: If needed, repeat this procedure for the remaining button to change to Genie

Summary of content (6 pages)

PAGE 1
Car2U® System Programming for Genie® Setting the Car2U to Factory Default settings The default setting for the Car2U system is: • Button 1= Genie Manufactured Openers • Button 2= LiftMaster® Manufactured Openers • Button 3= Wayne Dalton® Manufactured Openers 1 1. 2. 2 3 Press and hold buttons 1 and 3 for twenty seconds or until all three LED’s begin to flash. Release both buttons. The Car2U system is now set to the Factory Default settings. To Change One of the Other Manufacturer’s Buttons to Genie 1.
PAGE 2
Car2U® System Programming for GENIE Models IntelliG® 1000, IntelliG® 1200, TriloG™ 1200, TriloG™ 1500, GPower™ 900 Manufactured before July 2011 The label shown right is on the back of the powerhead. Use this instruction if the first 5 digits of the serial number from this label is 11188 or smaller. Programming Car2U to a Genie Opener 1. Press and hold the program button PRGM until the round blue LED and the long blue LED are on – release the button. The round blue LED will be on. 2.
PAGE 3
Car2U® System Programming for GENIE Models IntelliG® 1000, IntelliG® 1200, TriloG™ 1200, TriloG™ 1500, GPower™ 900 Manufactured before November 2011 The label shown right is on the back of the powerhead. Use this instruction if the first 5 digits of the serial number from this label is 11290 or smaller. Programming Car2U to a Genie Opener 1. Press and hold the program button PRGM until the round blue LED and the long blue LED are on – release the button. The round blue LED will be on. 2.
PAGE 4
Car2U® System Programming for Genie Models IntelliG® 1000, IntelliG® 1200, TriloG™ 1200, TriloG™ 1500, GPower™ 900, ReliaG® 650, ReliaG® 850 Manufactured after November 2011 The label shown right is on the back of the powerhead. Use this instruction if the first 5 digits of the serial number from this label is 11291 or greater. Programming Car2U to a Genie Opener 1. Press and hold the program button PRGM until the round blue LED release the button. The long LED will flash purple. is on – 2.
PAGE 5
Car2U® System Programming for older Genie Models If your learn button looks like this: Programming Car2U to a Genie Opener 1. Press and release the learn code button - the red LED will begin to blink. 2. Press the desired Car2U button one time. The red LED will stop blinking and stay on. 3. Press the desired Car2U button one more time. The red LED will go out. 4. Pressing the Car2U button again will cause the garage door to move.
PAGE 6
Car2U® System Programming for Genie Models ChainLift® 600, BeltLift® 600, ChainLift® 800, BeltLift® 800, ReliaG 600® , ReliaG 800® Programming Car2U to a Genie Opener 1. Press and release the learn code button the red LED will begin to blink. CODE 2. Press the desired Car2U button one time. The red LED will stop blinking and stay on. 3. Press the desired Car2U button one more time. The red LED will go out. 4. Pressing the Car2U button again will cause the garage door to move.