User Manual

1. Slowly press and release the remote button of your choice two
times. The opener LEDs will ash and go o, indicating you
have successfully programmed your remote.
2. Press and release the same button a third time and door will
open or close.
NOTE: It is possible to press the remote button too quickly or lightly. If
the LEDs do not go OFF, press the remote button several more times to
achieve conrmation.
1
Putting Opener into Programming Mode
New Genie® Openers
1. Press and hold the program button until the
round LED turns blue, then release.
PROGRAM
SET
+
PROGRAM
SET
+
PROGRAM
SET
+
PROGRAM
SET
+
2. The round LED will go out and the long LED
will begin ashing purple.
Proceed to step 2
-OR-
Genie® openers and external receivers manufactured between
1995 to 2011
RADIO
SIGNAL
LEARN
CODE
CODE
LEARN
SET
SET
OPEN
FORCE
CLOSECODE
LEARN LIMITMANUAL
or
RADIO
SIGNAL
LEARN
CODE
RADIO
SIGNAL
LEARN
CODE
1. Press & release Learn Code button once.
The red LED will begin to ash.
Proceed to step 2
2
Programming a Remote to the Opener
NOTE: Once in programming mode, you will have approximately 30 seconds to perform this step.
Note: While programing remote buttons, stand at least 5 feet away from the opener. This ensures
you have proper communication between the remote and the opener.
PROGRAM
SET
+
PROGRAM
SET
+
39658503537, 06/2017
PRGM
SET
TYPE 1
TYPE 2 TYPE 3
There are 3 types of programming button pads. Type 1 is shown in these steps. All buttons
perform the same function and programming is the same for all types shown above.
Place operator into programming mode:
TYPE 1-2-3
RADIO
SIGNAL
LEARN
CODE
- OR -
Place operator into programming mode:
WARNING
!
MOVING DOOR CAN CAUSE SERIOUS INJURY OR DEATH.
•DO NOT install transmitter unless the door operator’s safety device works as required by the door
operator’s manual.
•Wall Console must be mounted in sight of door, at least 5 feet above oor and clear of moving door
parts.
•Keep people clear of opening while door is moving.
•DO NOT allow children to play with the transmitter or door operator.
If safety reverse does not work properly:
•Close door then disconnect opener using the manual release handle.
•DO NOT use transmitter or door operator.
•Refer to Door and Door Opener Owner’s Manuals before attempting any repairs.
AVERTISSEMENT
!
UNE PORTE MOBILE PEUT ENTRAÎNER DES BLESSURES GRAVES VOIRE MORTELLES.
•NE PAS installer l’émetteur sans s’assurer d’abord que le dispositif de sécurité de la télécommande
fonctionne tel que requis dans le manuel de l’ouvre-porte.
•La console murale doit être installée en vue de la porte, à au moins 1,5 m au-dessus du sol et à l’écart des
pièces de la porte mobiles.
•Tenir toute personne à l’écart de l’ouverture de la porte pendant qu’elle est en mouvement.
•NE PAS laisser les enfants jouer avec l’émetteur ou la télécommande de l’ouvre-porte.
Si le système d’inversion de sécurité ne fonctionne pas correctement, procéder comme suit :
•Fermer la porte puis débrancher l’ouvre-porte en utilisant la poignée de déverrouillage manuel.
•NE PAS utiliser l’émetteur ni la télécommande de l’ouvre-porte.
•Se reporter aux manuels d’utilisateur de l’ouvre-porte et de la porte avant de procéder à une réparation.
Remote
Buttons
Flashlight
Button
New Genie® Openers
1. Press and hold the program button until the
round LED turns blue, then release.
2. Press and hold the Up(+) Down (-) buttons at the
same time, until the both LEDs ash blue and go OFF.
Genie® openers and external receivers manufactured between
1995 to 2011.
•Toeraseallremotedevicesfromallother
types of Genie® openers,
Press and hold the Learn Code Button until
the LED stops blinking.
Start at step 1 to reprogram your remotes.
NOTE: Clearing remote control memory from the power head will clear ALL programmed remotes
and wireless keypads. Your opener will no longer recognize any signal from any remote device,
including a missing remote device.
3
Lost or Stolen Remote/Erasing all Remotes
PROGRAM
SET
+
PROGRAM
SET
+
PROGRAM
SET
+
FCC Part 15.21 Statement:
Changes or modications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
FCC / IC Statement:
This device complies with FCC Part 15 and Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de
brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
For additional help or information, please visit our website at
www.GenieCompany.com, contact our Customer Care group at
1-800-35-Genie, or write to us directly at:
The Genie Company
One Door Drive, PO Box 67
Mount Hope, Ohio 44660
Replace the Battery
Replace remote battery with 1-AAA battery.
1. Remove screw and press down on top of battery door and slide
back o of remote.
2. Match battery polarity symbols inside battery housing and
replace battery.
3. Align cover, snap case closed, install screw.
NOTE: Transmitter will not require reprogramming for battery change.
AAA
Press the LED Flashlight button once.
LED Flashlight will operate until button is pressed again or when 4 minutes have
passed.
After 4 minutes the LED will ash indicating that light will turn o automatically.
4
Using the LED Flashlight
RADIO
SIGNAL
LEARN
CODE
RADIO
SIGNAL
LEARN
CODE
©2017 GMI Holdings, Inc. DBA The Genie Company. Pat: www.GenieCompany.com/patent
-OR-
Instruction pertains to all button pad TYPES shown in section 1