Instructions / Assembly

ManualsBrandsGeneral International ManualsJointers7.5 HP Parallelogram Jointer

RULES FOR SAFE OPERATION

1. Do not operate this jointer when tired, distracted,

or under the effects of drugs, alcohol or any me-

dication that impairs reﬂexes or alertness.

2. The work area should be well lit, clean and free

of debris.

3. Keep children and visitors at a safe distance when

the jointer is in operation; do not permit them to

operate the jointer.

4. Childproof and tamper proof your shop and all

machinery with locks, master electrical switches

and switch keys, to prevent unauthorized or unsu-

pervised use.

5. STAY ALERT! Give your work your undivided attention.

Even a momentary distraction can lead to serious

injury.

6. Fine particulate dust is a carcinogen that can be

hazardous to health. Work in a well-ventilated area

and whenever possible use a dust collector. Wear

face, eye, ear, respiratory and body protection

devices.

7. Do not wear loose clothing, gloves, bracelets, neck--

laces or other jewelry while the jointer is in opera-

tion. Wear protective hair covering to contain long

hair and wear non-slip footwear.

8. Be sure that adjusting wrenches, tools, drinks and

other clutter are removed from the machine and/or

the table surface before operating.

9. Keep hands well away from knives and all moving

parts. Use a push stick to feed stock, and a brush,

not hands, to clear away chips and dust.

10. Be sure that the knives are securely installed in the

cutter head.

11. Always use clean, properly sharpened knives.

Dirty or dull knives are unsafe and can lead to

accidents.

12. If using a power feeder, stop the feeder before

stopping the jointer.

13. Do not push or force stock into the cutter head. The

jointer will perform better and more safely when

working at the rate for which it was designed.

14. Be sure that the cutter head has gained full opera-

ting speed before starting to joint.

15. Avoid working from awkward or off balance posi-

tions. Do not overreach and keep both feet on ﬂoor.

16. Keep guards in place and in working order. If a

guard must be removed for maintenance or clean-

ing be sure it is properly re-attached before using

the tool again.

17. Use of parts and accessories NOT recommended

by General

International may result in equipment

malfunction or risk of injury.

18. Never stand on machinery. Serious injury could

result if the tool is tipped over or if the cutting tool is

unintentionally contacted.

19. Always disconnect the tool from the power source

before servicing or changing accessories such as

knives, or before performing any maintenance or

cleaning, or if the machine will be left unattended.

20. Make sure that the switch is in the “OFF” position be--

fore plugging in the power cord.

21. Make sure the tool is properly grounded. If equip-

ped with a 3-prong plug it should be used with

a three-pole receptacle. Never remove the third

prong.

22. Do not use this jointer for any purpose other than

its intended use. If used for other purposes, General

International disclaims any real or implied warranty

and holds itself harmless for any injury, which may

result from that use.

To help ensure safe operation, please take a moment to learn the machine’s applications and limitations,

as well as potential hazards. General

International disclaims any real or implied warranty and holds itself

harmless for any injury that may result from the improper use of it’s equipment.

Summary of content (10 pages)

PAGE 1
RULES FOR SAFE OPERATION To help ensure safe operation, please take a moment to learn the machine’s applications and limitations, as well as potential hazards. General® International disclaims any real or implied warranty and holds itself harmless for any injury that may result from the improper use of it’s equipment. 1. Do not operate this jointer when tired, distracted, or under the effects of drugs, alcohol or any medication that impairs reﬂexes or alertness. 2.
PAGE 2
ADDITIONAL SAFETY INSTRUCTIONS FOR JOINTERS Because each shop situation is unique, no list of safety guidelines can ever be complete. The most important safety feature of any shop is the knowledge and good judgement of the user. Use common sense and always keep safety considerations, as they apply to your individual shop conditions, ﬁrst and foremost in mind.
PAGE 3
ELECTRICAL REQUIREMENTS BEFORE CONNECTING THE MACHINE TO THE POWER SOURCE, VERIFY THAT THE VOLTAGE OF YOUR POWER SUPPLY CORRESPONDS WITH THE VOLTAGE SPECIFIED ON THE MOTOR I.D. NAMEPLATE. A POWER SOURCE WITH GREATER VOLTAGE THAN NEEDED CAN RESULT IN SERIOUS INJURY TO THE USER AS WELL AS DAMAGE TO THE MACHINE. IF IN DOUBT, CONTACT A QUALIFIED ELECTRICIAN BEFORE CONNECTING TO THE POWER SOURCE. THIS TOOL IS FOR INDOOR USE ONLY. DO NOT EXPOSE TO RAIN OR USE IN WET OR DAMP LOCATIONS.
PAGE 4
IDENTIFICATION OF MAIN PARTS AND COMPONENTS FRONT VIEW D F E H G C I A P P B O N N M L J REAR VIEW Q R K P A. OUTFEED TABLE K. WHEEL LOCK KNOBS B. OUTFEED TABLE ADJUSTMENT HANDWHEEL L. INFEED TABLE ADJUSTMENT HANDWHEEL C. RABBETING ARM M. TABLE LOCKING LEVER D. CUTTER HEAD GUARD N. TABLE DEPTH ADJUSTMENT LOCK PIN E. FENCE TILT LEVER O. ECCENTRIC ADJUSTERS F. P. DEPTH OF CUT INDICATOR G. FENCE Q. FENCE ADJUSTMENT HANDWEEL H. MAGNETIC SWITCH R. FENCE TILT LOCKING LEVER I.
PAGE 5
BASIC FUNCTIONS This 12” jointer is designed for face and edge jointing in solid wood only. The unit is not designed nor should it be used to surface or prepare plywood, wood panelling, particleboard, MDF, nor any other wood based by-products nor any non-wood based materials. The 80-325 features a precision four point parallelogram table adjustment system that allows for easy parallel alignment of infeed and outfeed table to the cutter head and to each other.
PAGE 6
CLEAN UP The protective coating on the jointer tables prevents rust from forming during shipping and storage. Remove it by rubbing with a rag dipped in kerosene, mineral spirits or paint thinner. (Dispose of potentially ﬂammable solventsoaked rags according to manufacturer’s safety recommendations.) A putty knife, held ﬂat to avoid scratching the surface, may also be used to scrape off the coating followed by clean-up with solvent.
PAGE 7
ASSEMBLY INSTRUCTIONS For your convenience this jointer is shipped from the factory partially assembled and requires only minimal assembly and set up before being put into service. SERIOUS PERSONAL INJURY COULD OCCUR IF YOU CONNECT THE MACHINE TO THE POWER SOURCE BEFORE YOU HAVE COMPLETED THE INSTALLATION AND ASSEMBLY STEPS. DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL INSTRUCTED TO DO SO.
PAGE 8
ADJUSTING AND SETTING THE OUTFEED TABLE HEIGHT The outfeed table should be set level with the highest point of the knives A. The height of the outfeed table should be veriﬁed and adjusted prior to ﬁrst use. It should also be veriﬁed and re-adjusted periodically to compensate for knife wear and also upon knife replacement. ALWAYS DISCONNECT THE MACHINE FROM THE POWER SOURCE BEFORE MAKING ANY ADJUSTMENTS. FAILURE TO HEED THIS WARNING CAN LEAD TO SERIOUS PERSONAL INJURY.
PAGE 9
1. Loosen the infeed (right) table locking lever C. 2. Flip the handle down then use the handwheel B to adjust the infeed table height to the desired depth of cut. D Note: Refer to the graduated depth scale D. 3. Flip handle B up to allow you to keep the handwheel from interfering while jointing. 4. Re-tighten locking lever C to secure the infeed table in position. C B TABLE ALIGNMENT The outfeed table and infeed table have been factory set parallel to the cutter head and to each other.
PAGE 10
ADJUSTING THE FENCE AND SETTING THE FENCE STOPS (CONTINUED) H K L J M I N To set the 45° outward fence stop: To set the 45° inward fence stop: 1. Using a combination or machinists square, set the fence to 45° outward H. 1. Using a 45° combination or machinists square, set the fence to 45° inward K. 2. Loosen the jam nut I on the 45° outward fence stop bolt. 2. Flip the 90° stop into position L. 3. Loosen the jam nut M. 3.