Instructions / Assembly

ManualsBrandsGeneral International ManualsDrill Presses14 in. Variable Speed Drill Press

ASSEMBLY INSTRUCTIONS

Before proceeding with the assembly, read the operating and maintenance instructions manual and familiarize

yourself with correct assembly, setup, maintenance and safety procedures.

1. Place the base (1) on a flat surface and screw the column (8), to the base.

2. Remove the rack ring (9) from the column (8).

3. Insert the rack (11) into the table bracket and position the 2 pieces onto

the column at the same time. The bottom lip of the rack is pressed bet-

ween the column and the flange. The top lip of the rack is similarly secured

with the replacement of the rack ring (9). Tighten the set screw in the rack

ring. Place the handle (10) on the worm gear and secure it with the hex

head bolt.

Attach the head (2) to the column and tighten the head with the set screws (3).

5. Secure the table onto the table arm.

6. Attach the 3 feed handles, (4, 5 & 6), to the handle body (7).

7. If desired, install a max. 60 watt light bulb

(not included) for the worklight (12).

Once assembled, clean the protective coating from all surfaces (where

applicable) using a rag dipped in kerosene, mineral spirits or paint thin-

ner. (Dispose of potentially flammable solvent-soaked rags according to

manufacturer’s safety recommendations.) A putty knife, held flat to avoid

scratching the surface, may also be used to scrape off the coating fol-

lowed by clean-up with solvent. Avoid rubbing painted surfaces, as many

solvent-based products will remove paint.

14” DRILL PRESSES

75-025 • 75-125

INSTALL THE CHUCK GUARD

Fit the chuck guard onto the quill and tighten the

Phillips screw to secure the chuck guard in place.

ADJUSTING AND USING THE CHUCK GUARD

1. Loosen the wing nuts on both sides of the chuck

guard and slide the chuck guard extension down

along the two slots to the desired height .

2. Tighten the wing nuts to lock the chuck guard exten

sion in place.

Note: To facilitate drill bit installation / removal, flip the spring

loaded chuck guard up as shown in to keep it out of the

way.

REAR VIEW

TO PREVENT THE RISK OF SERIOUS INJURIES, ALWAYS

COVER THE CHUCK AND DRILL BIT WITH THE CHUCK

GUARD WHEN USING THE DRILL PRESS.

TO AVOID RISK OF SERIOUS INJURY, MAKE SURE THE DRILL PRESS IS

INSTALLED ON A FLAT, SOLID AND STABLE SURFACE.

Summary of content (4 pages)

PAGE 1
4” DRILL PRESSES 75-025 • 75-125 A S S E M B LY I N S T R U C T I O N S Before proceeding with the assembly, read the operating and maintenance instructions manual and familiarize yourself with correct assembly, setup, maintenance and safety procedures. TO AVOID RISK OF SERIOUS INJURY, MAKE SURE THE DRILL PRESS IS INSTALLED ON A FLAT, SOLID AND STABLE SURFACE. 1. Place the base (1) on a flat surface and screw the column (8), to the base. 2. Remove the rack ring (9) from the column (8). 3.
PAGE 2
INSTALLING THE CHUCK 1. Slide the arbor into the quill assembly, flat end goes in first. 2. Slide the chuck onto the tapered end of the arbor and using the feed handle, lower the quill assembly against the table to secure the chuck. (To avoid damaging the chuck place a piece of wood on the table.) REMOVING THE CHUCK AND ARBOR 1. Turn “OFF” and disconnect the drill from the power source. 2. Using feed handle, lower the quill assembly. 3. Insert tool into, and all the way through the quill assembly.
PAGE 3
ADJUSTING TABLE HEIGHT TABLE SWING ADJUSTMENT TABLE ROTATION ADJUSTMENT 1. 1. Loosen column lock handle (1). 1. Loosen the table lock handle (3). 2. 2. Turn the crank handle (2) until the table is at the desired height. Swing the table arm bracket and the table to the desired position. Rotate the table to the desired position. 3. Retighten column lock handle (1). 3. Retighten the table lock handle (3). Retighten the column lock handle (1) before starting.
PAGE 4
CHANGING SPEEDS MAKE SURE THE DRILL PRESS HAS COME TO A COMPLETE STOP BEFORE CHANGING SPEEDS. REFER TO THE SPINDLE SPEED SELECTION CHART LOCATED ON THE INSIDE OF THE SPINDLE COVER. 1. Disconnect the drill press from the power source. 2. Loosen the slide bar bolt (1) located on the right side of the head. 3. Pull the motor (2) in towards the head to loosen the belts. 4. Relocates belts to the desired pulleys to select a new spindle speed. 5. Push the motor (2) back, away from the head. 6.