Rotating, 45° tilting, crank-operated worktable with quick release clamp. Large front mounted stop switch with lock-out safety feature to prevent unwanted or unintentional start-up. Adjustable spindle tension return spring. Built-in lamp illuminates the drilling area. Spindle is supported by high quality ball bearings. Cast-iron pulleys reduce vibration. Industrial 1/2 HP motor. Heavy-duty positive depth stop for quick adjustment. 5/8” drill chuck.
GENERAL® INTERNATIONAL 8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3 Telephone (514) 326-1161 • Fax (514) 326-5555 • www.general.ca THANK YOU for choosing this General International model 75-030 Drill Press. This drill press has been carefully tested and inspected before shipment and if properly used and maintained, will provide you with years of reliable service.
Rules for Safe Operation To help ensure safe operation, please take a moment to learn the machine’s applications and limitations, as well as potential hazards. General® International disclaims any real or implied warranty and holds itself harmless for any injury that may result from improper use of its equipment. 1. Do not operate the drill press when tired, distracted, or under the effects of drugs, alcohol or any medication that impairs reflexes or alertness. 12.
14” DRILL PRESS 75-030 A S S E M B LY I N S T R U C T I O N S Before proceeding with the assembly, read the operating and maintenance instructions manual and familiarize yourself with correct assembly, setup, maintenance and safety procedures. To avoid risk of serious injury, make sure the drill press is installed on a flat, solid and stable surface. 1. Place the base (1) on a flat surface and screw the column (8), to the base. 2. Remove the rack ring (9) from the column (8). 3.
CONNECTING TO A POWER SOURCE Plug the drill into a proper receptacle. Your power tools should be connected to a dedicated electrical circuit of not less than #14 wire and should be protected with a 15 amp time lag fuse. If an extension cord is needed, use only 3-wire cords with 3-prong grounded-type plugs and 3-pole receptacles. Grounding: This tool must be grounded to protect the operator from electrical shock.
ADJUSTING TABLE HEIGHT TABLE SWING ADJUSTMENT TABLE ROTATION ADJUSTMENT 1. 1. Loosen column lock handle (1). 1. Loosen the table lock handle (3). 2. 2. Turn the crank handle (2) until the table is at the desired height. Swing the table arm bracket and the table to the desired position. Rotate the table to the desired position. 3. Retighten column lock handle (1). 3. Retighten the table lock handle (3). Retighten the column lock handle (1) before starting.
CHANGING SPEEDS MAKE SURE THE DRILL PRESS HAS COME TO A COMPLETE STOP BEFORE CHANGING SPEEDS. REFER TO THE SPINDLE SPEED SELECTION CHART LOCATED ON THE INSIDE OF THE SPINDLE COVER. 1. Disconnect the drill press from the power source. 2. Loosen the slide bar bolt (1) located on the right side of the head. 3. Pull the motor (2) in towards the head to loosen the belts. 4. Relocates belts to the desired pulleys to select a new spindle speed. 5. Push the motor (2) back, away from the head. 6.
RECOMMENDED OPTIONAL ACCESSORIES We offer a large variety of products to help you increase convenience, productivity, accuracy and safety when using your drill press Here’s a small sampling of optional accessories available from your local General International dealer. For more information about our products, please visit our website at www.general.ca 25 PIECE - RUBBER DRUM SANDING SET #75-025 Turn your drill press into a mini drum sander. Ideal for small sanding jobs on curved or odd shaped pieces.
PARTS LIST 75-030 PART N0.
PARTS LIST 75-030 9 PART N0.
DIAGRAM 64 65 66 SIDE A 40 68 67 80 69 85(2) 62 63 75 76 40-1 78 81 77(2) 79 82 84 83 61 72 60 32-1 73 33 74 40 41 42 34 31 32 EA SI D 71 59 40-1 58(2) 30(2) 29(4) 28-1 27 56(2) 57 28 26-1 36(3) 35N26-2 35-2N 35-1N 39(3) 37 26 25 44 45 38N 43 23(3) 22(3) 21 46 43 24 20 47 41 48 51 19 50 52 18N 87 53 49 49-1 10 11 54 7-1 55 9 12-1 12 88 4 17 8 7 6 5 16 13 15 14 3(4) 2(4) 1 10
75-030 8360, Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3 Tel.: (514) 326-1161 Fax : (514) 326-5565 Parts & Service Fax : (514) 326-5555 Order Desk orderdesk@general.ca www.general.ca IMPORTANT: When ordering replacement parts, always give the model number, serial number of the machine and part number. Also a brief description of each item and quantity desired.
