User's Manual
Table Of Contents
- Getting Started
- Wizards
- Using the Startup Wizard
- Using the Wireless Wizard to Configure the Wireless Settings for ISA550W and ISA570W
- Using the DMZ Wizard to Configure the DMZ Settings
- Using the Dual WAN Wizard to Configure the WAN Redundancy Settings
- Using the Site-to-Site Wizard to Establish the Site-to-Site VPN Tunnels
- Using the Remote Access Wizard to Establish the IPSec VPN Tunnels or SSL VPN Tunnels for Remote Access
- Status
- Networking
- Configuring IP Routing Mode
- Port Management
- Configuring the WAN
- Configuring the WAN Redundancy
- Configuring the VLAN
- Configuring the DMZ
- Configuring the Zones
- Configuring the Routing
- Dynamic DNS
- IGMP
- VRRP
- Configuring the Quality of Service
- Address Management
- Service Management
- Wireless Configuration for ISA550W and ISA570W
- Firewall
- Configuring the Firewall Access Rules to Control Inbound and Outbound Traffic
- Configuring the Firewall Schedule
- Firewall Access Rule Configuration Examples
- Configuring the NAT Rules to Securely Access a Remote Network
- Configuring the Session Settings
- Configuring the Content Filtering to Control Access to Internet
- Configuring the MAC Filtering to Permit or Block Traffic
- Configuring the IP/MAC Binding to Prevent Spoofing
- Configuring the Attack Protection
- Configuring the Application Level Gateway
- Security Services
- VPN
- About VPN
- Configuring the Cisco IPSec VPN Server
- Configuring the Cisco IPSec VPN Client
- Configuring the Site-to-Site VPN
- Configuring the SSL VPN
- Elements of the SSL VPN
- Configuration Tasks to Establish a SSL VPN Tunnel
- Installing the Cisco AnyConnect VPN Client on User’s PC
- Importing the Certificates for User Authentication
- Configuring the SSL VPN Users
- Configuring the SSL VPN Gateway
- Configuring the SSL VPN Group Policies
- Configuring the SSL VPN Portal
- Configuring the L2TP Server
- Configuring the VPN Passthrough
- Viewing the VPN Status
- User Management
- Device Management
- Remote Management
- Administration
- SNMP
- Configuration Management
- Firmware Management
- Log Management
- Managing the Security License
- Managing the Certificates for Authentication
- Configuring the Email Alert Settings
- Configuring the RADIUS Servers
- Configuring the Time Zone
- Device Discovery
- Diagnosing the Device
- Measuring and Limiting Traffic with the Traffic Meter
- Configuring the ViewMaster
- Configuring the CCO Account
- Configuring the Device Properties
- Configuring the Debug Settings
- Troubleshooting
- Technical Specifications and Environmental Requirements
- Factory Default Settings
- Where to Go From Here
Wizards
Using the Wireless Wizard to Configure the Wireless Settings for ISA550W and ISA570W
Cisco ISA500 Series Integrated Security Appliance Administrator Guide 42
2
• Enable: Check this box to enable the SSID.
• Mode: Choose the wireless connectivity type for each enabled SSID.
- Intranet WLAN Access: Allows wireless users to access the corporate
network via the wireless network. The WLAN is mapped to the DEFAULT
VLAN.
- Guest WLAN Access: Only allows guest users to access the corporate
network via the wireless network. The WLAN is mapped to the GUEST
VLAN.
- Guest WLAN Access (Captive Portal): Only allows guest users who
authenticated successfully to access the corporate network via the
wireless network. The wireless users will be directed to a specific web
authentication login page to authenticate, and then be directed to a
specified web portal after login successfully before they can access the
Internet.
NOTE Only one SSID can be set for Guest WLAN access and Captive Portal
WLAN access.
STEP 4 Specify the wireless connectivity settings for all enabled SSIDs.
Depending on the wireless connectivity type that you selected for the SSID, you
need to complete the relevant settings for each enabled SSID.
For complete details to configure the Intranet WLAN access, see Configuring the
SSID for Intranet WLAN Access, page 43.
For complete details to configure the Guest WLAN access, see Configuring the
SSID for Guest WLAN Access, page 44.
For complete details to configure the Captive Portal WLAN access, see
Configuring the SSID for Guest WLAN Access (Captive Portal), page 45.
STEP 5 After you are finished, click Next.
The Summary window opens. The Summary page displays the summary
information for all configurations you made for the SSIDs.
STEP 6 Click Submit to save your settings and exit the Wireless Wizard.