User's Manual
Table Of Contents
- Getting Started
- Wizards
- Using the Startup Wizard
- Using the Wireless Wizard to Configure the Wireless Settings for ISA550W and ISA570W
- Using the DMZ Wizard to Configure the DMZ Settings
- Using the Dual WAN Wizard to Configure the WAN Redundancy Settings
- Using the Site-to-Site Wizard to Establish the Site-to-Site VPN Tunnels
- Using the Remote Access Wizard to Establish the IPSec VPN Tunnels or SSL VPN Tunnels for Remote Access
- Status
- Networking
- Configuring IP Routing Mode
- Port Management
- Configuring the WAN
- Configuring the WAN Redundancy
- Configuring the VLAN
- Configuring the DMZ
- Configuring the Zones
- Configuring the Routing
- Dynamic DNS
- IGMP
- VRRP
- Configuring the Quality of Service
- Address Management
- Service Management
- Wireless Configuration for ISA550W and ISA570W
- Firewall
- Configuring the Firewall Access Rules to Control Inbound and Outbound Traffic
- Configuring the Firewall Schedule
- Firewall Access Rule Configuration Examples
- Configuring the NAT Rules to Securely Access a Remote Network
- Configuring the Session Settings
- Configuring the Content Filtering to Control Access to Internet
- Configuring the MAC Filtering to Permit or Block Traffic
- Configuring the IP/MAC Binding to Prevent Spoofing
- Configuring the Attack Protection
- Configuring the Application Level Gateway
- Security Services
- VPN
- About VPN
- Configuring the Cisco IPSec VPN Server
- Configuring the Cisco IPSec VPN Client
- Configuring the Site-to-Site VPN
- Configuring the SSL VPN
- Elements of the SSL VPN
- Configuration Tasks to Establish a SSL VPN Tunnel
- Installing the Cisco AnyConnect VPN Client on User’s PC
- Importing the Certificates for User Authentication
- Configuring the SSL VPN Users
- Configuring the SSL VPN Gateway
- Configuring the SSL VPN Group Policies
- Configuring the SSL VPN Portal
- Configuring the L2TP Server
- Configuring the VPN Passthrough
- Viewing the VPN Status
- User Management
- Device Management
- Remote Management
- Administration
- SNMP
- Configuration Management
- Firmware Management
- Log Management
- Managing the Security License
- Managing the Certificates for Authentication
- Configuring the Email Alert Settings
- Configuring the RADIUS Servers
- Configuring the Time Zone
- Device Discovery
- Diagnosing the Device
- Measuring and Limiting Traffic with the Traffic Meter
- Configuring the ViewMaster
- Configuring the CCO Account
- Configuring the Device Properties
- Configuring the Debug Settings
- Troubleshooting
- Technical Specifications and Environmental Requirements
- Factory Default Settings
- Where to Go From Here
Device Management
Managing the Security License
Cisco ISA500 Series Integrated Security Appliance Administrator Guide 309
10
NOTE To send the alert email for license expiration events, you first need to
enable the License Expiration Alert feature and configure the email
account settings in the Email Alert Setting page. Click the link or go
to the Device Management -> Email Alert Settings page to do this.
See Configuring the Email Alert Settings, page 316.
Renewing the Security License
Perform the following steps to renew the security license before it expires.
STEP 1 Contact your Cisco reseller to purchase a new license.
STEP 2 Launch the the Configuration Utility and login, go to the Device Management ->
License Manaagement page.
STEP 3 Click Renew.
The Install License window opens.
STEP 4 The license can be a license code (PAK) or a license file downloaded from
cisco.com. Choose the license type from the License Type drop-down list:
• License Code (PAK) from cisco.com: Automatically retrieves and installs
the license on the security appliance from the Cisco server. If you choose
this option, enter the following credential information. These credentials are
required to authenticate to the Cisco server.
- License Code: Enter the license code (PAK).
- Cisco.com Login: Enter the user name of your CCO account to log into
Cisco.com.
- Cisco.com Password: Enter the password of your CCO account to log
into Cisco.com.
- Email Address: Enter the registered email address to receive the PAK.
• License File Download from cisco.com: Installs the security license that
was previously downloaded to your PC. If you choose this option, click
Browse to locate and select the license file from your PC.