Downdraft Vent systems 36" Wide Models: ZVB36 30" Wide Models: ZVB30 Monogram_ _ We bring go_Jflthings to life,
Safetv Information BEFORE YOU BEGIN WARNING Read/these instructions and carefully. To reduce the risk of fire, electric completely JMPORTANT - Save these instructions for local inspector's use. iMPORTANT= Observe all governing B. Before service or cleaning unk, switch power off at service panel and Iockthe service disconnecting means to prevent power from being switched on accidentafly.
Design information Design Information Models Available ...............................................................3 Accessories .......................................................................3 Product Dimensions ..........................................................3 Tools and Materials Required .........................................9 Remove Packaging ...........................................................9 Power Supply ...............................................................
Design mnformation ADVANCE Remote PLANNING Before you begin, you must: 1. Review countertop dimension illustrations to be sure you will have enough flat countertop surface. 2. Checkto be sure that the total countertop depth required (including minimum cutout to front edge depth) allows enough space for a backsplash. 3. Reviewthe cabinet illustration. Checkto be sure Switch The downdraft vent has a separate raise/lower switch.
Design mnformation Clearances Ductwork • The downdraft system with blower, motor and duct work will occupythe cabinet below the countertop and cooktop. ,The blower!motor assembly can be located below the cabinet floor. The assemNywill fit between 16" floor joists. Order JXRB67 for indoor remote locations. Prepare ductwork to vent to the outdoors. • Use the shortest and straightest duct run possible. , The maximum permissible length for duct run is 150 feet.
mnstaJiation Preparation CUTOUTS AND CLEARANCES * Identify the cutout illustration for the cooktop model you are installing. * Draw Bines on the countertop to follow as a cutting guide, Measure and marl< cooktop and vent overBaps to be sure there is enough flat countertop depth, * Measure carefully when cutting the countertop. Make sure sides of the opening are parallel and rear and front cuts are exactly perpendicuBr to sides.
Installation ZEU30R DIGITAL COOKTOPS Preparation WITH 30" VENT 2-1/2" to Cutout 1-3/4" Min. Cool
mnstaliation ZGU36GG GAS COOKTOPS Preparation WITH 36" VENT 2-1/4" Min. Cool
Installation Preparation / CAUTION Wall coverings, countertops and cabinets shouN wkhstand 200° heat generated by any cooktop. Gas- 6" to 11-9/16" Electric- 2" Clearance to Side Walls PRUDENCE Les rev_tements muraux, Jes dessus de comptoir et les armoires de cuisine doivent r_sister a Ja temp6rature de 95 -oC(200 -°F)cr_6e par toute table de cuisson. Max. 1 Max. [------------- 8" MJn. to Wall When Installed 2" Min.
mnstaliation Preparation POWER SUPPLY FOR Do Not Locate Gasor Electrical Connections Within Shaded Area PERSONAL SAFETY: Remove house fuse or open circuit breaker before beginning instaflation. Outlet 12" Above Cabinet Floor Do not use an extension cord or adapter plug with this appliance. Follow National electrical codes or prevailing local codes and ordinances.
JnstaJJation Preparation LoosenScrews VENTING OPTIONS toAdjust 3-1/2" to Left or Right_ The downdraft vent is shipped with the discharge outlet pointing straight down and can be changed to the left or right side. The blower outlet is sized for 3ol/4" x 10" and can be transitioned to 6" round. Side to side adjustments: The entire blower mounting plate can be adjusted 3-1/2 " to the left or right.
Ductwork Use this form to compute maximum permissible lengths for duct runs to outdoors. Total Duct Piece Dimensions Equivalent Quantity Equivalent Length* Used Lengtb I ft. 6" round, (per foot straight lengtb} 3-!/4" x I0" (per foot straight length) Nete: Do not exceed I ft. maximum permissible equivalent lengthsT Flexibme dactiag: If flexible metal 6" ducting is used, aH the equivalent feet values in the table should be doubled. The flexibUe metal duct should be 96° elbow I5 ft.
Instamiation [STEP llJNSTALL Instructions [STEP 21 iNSTALL THE DUCTWORK DOWNDRAFT Place the downdraft vent into the countertop against the back side. The downdraft blower system is designed for use with 3-1/4" x 10"ductwork. It can be transitioned to 6" round. * Ductwork MUST be vented tothe outside - never in a cutout, crawl space, attic or other enclosed space. 6" PVC duct should be used when installing under a concrete sial _Upper _r _,_\ %, \ '\ \ Note: Local building code must be followed for i
mnstamiation [STEP 31 iNSTALL RAiSE/LOWER mnstructions SWITCH AVERTiSSEMENT WARNING: Disconnect electrical power from unit before beginnhlg switch installation. Failure to do so could result in personal injury or damage to the electrical controls. II faut d_brancher Valimentation _lectrique de Vappareil avant de commencer I'installation de Hnterrupteur. II faut suivre cette directive pour _viter des Nessures ou endommager les commandes _lectriques. Determine the location for the RAISE/LOWER switch.
mnstaJiation ISTEP 4] CONNECT mnstructions POWER Cleaning a Stainless Steel Downdraft Vent Stainless steel has some unique cleaning characteristics. In order to keep your vent looking like new, we suggest cleaning it with Stainless Steel Magic or similar product. Plug power cord into properly grounded receptacle. ISTEP 5] iNSTALL RLTERS, CHECK OPERATION Stainless Steel Magic is available at Ace, True Value, Servistar, HWl and other leading stores.
Note: While performing installations described in this book, safety glasses or goggles should be worn, t4_ M};_zog'l-_l _/o_'_l _n, _'_i_ },_J_l _*_, _'_fl Webringgoodthingsto life, GE Consumer Producls Pub.No.49-80185 Dwg.No.