Installation Instructions If you have questions, call 800.GE.CARES or visit our website at: www.monogram.
Installation Instructions BEFORE YOU BEGIN CAUTION: THESE COOKTOPS SHOULD BE INSTALLED IN CONJUNCTION WITH A SUITABLE OVERHEAD VENT HOOD. Due to the high heat capacity of this unit, particular attention should be paid to the hood and duct work installation to assure it meets local building codes. Read these instructions completely and carefully. • IMPORTANT – Save these instructions for local inspector’s use. • IMPORTANT – Observe all governing codes and ordinances.
Design Information CONTENTS Installation Instructions Step 1, Remove Packaging ..............................................7 Step 2, Cut the Countertop Opening ..............................7 Step 3, Install the Cooktop ..............................................8 Step 4, Connect Cooktop to Gas......................................8 Step 5, Connect Electrical ................................................9 Step 6, Assemble Burners, Check Ignition....................9 Finalize Installation ...........
36" Wide Hood Refer to Hood Installation Instructions 18" Min. 2" 7" 13" Max. 12" Min. to Combustible Material Each Side 1/2" 35" Cooking Surface 2-1/2" 22-3/4" Min. Electric/Gas Supply 8" 9-1/2" 3/4" 22" 12" 26-5/8" 36" Min. 22" High Backsplash to Combustibles with Shelf 12" High Backsplash 36" Min.
Installation Preparation INSTALLATION OPTIONS ADVANCE PLANNING These cooktops can be installed in standard 24" or deeper 25" cabinets. Refer to “Dimensions and Clearances” for appropriate placement and necessary clearances when planning the installation. • In 24" deep cabinets, the front of the cooktop will project approximately 1-7/8" beyond the front of the countertop. • Cabinetry cannot be installed directly above the cooktop.
Installation Preparation TOOLS REQUIRED MATERIALS REQUIRED (not supplied) • Saw • Measuring tape • Carpenter’s square • Large flat-blade screwdriver • Pipe wrench • Pipe and fittings as required • Manual gas line shut-off valve • Gas pressure regulator (supplied) • Gas-resistant pipe joint sealant • 5 foot, 5/8" AGA-certified flexible metal gas supply line (length must comply with local codes) – If required by local codes, use solid pipe fittings. NOTE: Purchase new flexible line.
26-5/8" 47-7/8" Allow Clearance Below the Burner Box for the Regulator and Gas Connections REAR FRONT REAR FRONT REAR am Monogr FRONT 46-1/8" HEATING 8-7/16" 22-3/4" 22-3/4" 7/8" 1/2" 2-1/2" 8" 8" 48" wide models are designed to fit in 48" or wider base cabinets Measure carefully when cutting the countertop. Make sure sides of the opening are parallel. • These cooktops require 8" free space below the countertop to house the cooktop burner box.
Installation STEP 3 INSTALL COOKTOP • Lower the cooktop into the opening. Make sure the cooktop is evenly seated and supported. A side frame gasket will seal the cooktop to the countertop. • “L” brackets with screws are provided to secure the cooktop to the countertop or to adjacent cabinetry. – Alternate screw hole locations on the sides of the cooktop allow for varying thicknesses of countertops or side cleats. • Select the bracket location; secure the bracket to the cooktop with 2 screws.
Installation STEP 5 CONNECT ELECTRICAL Plug power cord into properly grounded receptacle. STEP 6 ASSEMBLE BURNERS, CHECK IGNITION Assemble burners as shown. Check to be sure that burner heads and caps are securely seated. Pin(s) must completely engage holes to ensure proper assembly. • Check for proper ignition: – Push in one control knob and turn 90° to Lite position. – The igniter will spark and the burner will light; the igniter will cease sparking when the burner is lit.
Installation FINALIZE INSTALLATION Place the burner grates over the burners. Press corner of the grate to the cooktop. The grates should be seated and should not rock. The grill and griddle are secured with screws at the front. They are designed to be stationary and should not be removed. The griddle has two leveling screws beneath the rear flue cover that can be used to adjust to the desired slope. The center screw is for shipping purposes only and can be removed.
INSTALL 9” or 12” HIGH BACKSPLASH • Install and level the range or cooktop according to the installation instructions. • Remove the backsplash packaging. Select the back, wall mount panel with mounting screw slots. • Mark a horizontal line on the wall, 1/8" above the range/cooktop backguard. • Use wood screws or fasteners (not supplied) to secure the back section to the wall. Slide the panel up or down to provide the 1/8" gap between the top of the range/cooktop and the bottom of the backsplash.
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram ® local service in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Pub. No. 49-80225-2 Part No. 164D4290P377 17713 Rev.
