Built-In Wall Oven 27" (68.6 cm) models JKS10, JKP30, JKP35, JKP55, JKP70, JKP75, PK916, PK956, ZEK938, ZEK958 Ilnstallat!on nstruct=ons 30" (76.2 cm) models JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960, ZET938, ZET958 If you have questions, call 1.800.GE.CARES ge.com Before You Begin Read these instructions carefully and completely. • IMPORTANT-save instructions these for local inspector's • IMPORTANT-observe use. all governing codes and ordinances.
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS For Your Safety Electrical • Be sure your oven is installed properly by a qualified installer or service technician. Requirements • Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit, stand or hang on the oven door.
Installation Instructions Pre-lnstallation Checklist Door removal is not a requirement for installation of the product, but is an added convenience. To remove the door: ALL INSTALLATION INFORMATION ON THE FOLLOWING PAGES IS TO BE USED FOR SINGLEAND DOUBLE OVEN INSTALLATION! Open the oven door as far as it will go. i Remove packaging materials. Check behind hinges and under false bottom.
Jation J for 27" (68.6 ui n On For JKSI0, JKP30, JKP70, PK916, ZEK938 models Cabinet 5" (12.7 era) Max. from the left or right Cabinet --Width _ 1 Cutout Width (63.5 era) Min. 25 1/4" (64.1 Max, _" Width 27" (68.6 cm) Recommended Cutout Location from Floor Box Location " 25" Junction _ side only. / 32 1t2" (82.6 cm) Cutout Depth 23 1/2" (59.7 cm) Min. Cutout 25" (63.6 cm) Min. Width 26 1/4" (64.1 cm) Max. Cutout Height 22" (55.g era) 27 5/8" Min. above base rail (70.
lation I for 27"(68.6cm) For JKP35, JKP55, JKP75, PK956, ZEK958 i Junction Box __._ over only. Cabinet Width 27" (68.6 erR) Recommended Cutout Location from Floor 13 114" (33.7 erR) Cutout Depth 23 5/8" (60 erR) Min. Cutout Width 25" (63.5 erR) Min. Location AHow I" (2.5 era) for oveHap of oven models side 25 1/4" (64.t erR) Max. edges of (111.8 cm) Min. icut°ut Above iHeight base rai_ i4911/16" [(126.2 cm) Mira ]50 1/8" i(127.3 cm) Max. Cutout Height 50 t/8" (127.3 erR) Max.
[ation [ for 27" (68.6 cm) j er Cou For JKS10, JKP30, JKPT0, PKPl6, ZEK938 r models only. Gas or electric cooktope may be installed over this oven. See eooktop installation instructions for cutout s{ze. See _abe_on top of oven for approved cooktop models. -\ 240V / 208V Junction Box Location 5" (12.7 cm) Max. from the [eft or right side \ Gas and e{ectrical connections for gas cooktop must be _ocated in an adjacent accessible _oeation to the right.
C [] le or On a awer For JKS10, JKP30, JKP35, ZEKg58 models only. JKPS5, JKPT0, JKPT5, PK916, PK956, ZEK938, SingJe 27" (68.6 cm) Oven Over a Warming Drawer Double 27" (68.6 cm) Oven Over a Warming Drawer Anti-Tip B_ock Against Rear •Wal_ Per Warming , Anti-Tip Block Against Rear Wa_[ Per Warming Drawer Requirement Drawer Requirement 2" (5.t era) Min. NOTE: Install the oven only with specific modets listed on the label located on top of the oven.
for 27" (68.6 cm) e Ovens only - ;rowave Oven Or Or Or a For JKS10, JKP30, JKP70, rming PKgl& ZEK938 Single 27" (68.6 cm) Oven Below an Advantium or Microwave Oven modems only. Singme 27" (68.6 cm) Oven Between an Advantium or Microwave Oven and a Warming Drawer Per Advantium or Microwave Oven Requirement Per Advantium or Microwave Oven Requirement Note: Install the oven only with specific models listed on the label located on top of the oven. 2" (&t era) Min.
Installation Instructions Cutout for 30"(76.2 Ovens only Built-In cm)Single For JTP30, JTP70, PT916, PT920, ZET938 models only. Cutout Width 28 1/2" (72.4 cm), 7 3/4" (19.7 cm) Max. Junction Box -_Location 28 5/8" (72.7 cm). Max. may be located in adjacent Allow 11/16" (1.75 cm) for overlap of oven over side edges of cutout _- Min. / --__ cabinet) (junction box Cabinet Width 30" (76.2 cm) Recommended Cutout Location from Floor 32 1/2" (82.6 cm) Cutout Depth 23 1/2" (69.7 cm) Min.
Installation Instructions IAICutoutfor30' 6.2cm)Double Built-InOvensonly For JTP35, JTP55, JTP75, PT956, PT960, ZET958 models only. Cutout Width 28 112" (72.4 cm) Min, 28 518" (72.7 cm) ==: Max. 7 3/4" (19.7 cm Junction Box ) Location (junction box may be located in adjacent cabinet) I / Allow 11/16" (1.75 cm) for overlap of oven over side edges of cutout Allow a minimum of 21" (53.
Installation Instructions IA1Cutout for 30" (76.2cm) Single Built-InOvens only Under Counter For JTP30, JTP70, PT916, PT920, ZET938 Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models. models only. 240V / 208V Junction Box ,\ Location (junction box may be in adjacent cabinet) 7 3/4" 25" (63.5 cm) (19.7 cm) \_ Top and/or side fillers may be necessary if unit is positioned between existin
Cabinetry Cutout for 30"(76.2cm) Single or Double Built-In Ovens only- Over a Warming Drawer For JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960, ZET938, ZET958 models only. Double 30" (76.2 cm) Oven Over a Warming Drawer Single 30" (76.2 cm) Oven Over a Warming Drawer Block Against Rear Wall Per Warming Drawer Requirement Anti-Tip Block Against Rear Wall Per Warming Drawer Requirement 2" (5.1 cm) Min. NOTE: install the 2" (5.1 cm) Min.
30" (76.2cm) or or ;rowave Oven or a rming Drawer For JTP30, JTP70, PTg16, PTg20, ZETg38 SingMe30" (7&2 cm) Oven BeMowan Advantium or Microwave Oven models only. SingMe30" (76.2 cm) Oven Between an Advantium or Microwave Oven and a Warming Drawer Per Advantium Microwave Oven Requirement Per Advantium Microwave Oven Req Note: Install the oven only with specific models listed on the label located on top of the oven.
Installation Instructions Electrical Connections ATTENTION Turn off the circuit breaker or remove fuses to the oven branch circuit. INSTALLER All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. With the oven supported on a table or platform in front of the cabinet opening, connect the flexible conduit to the electrical junction box as shown below.
Installation Instructions New Construction and Four-Conductor Branch Circuit Connection • When installing in new construction, • When installing in a mobile home, or • When installing in a recreational Three-Conductor Branch Circuit Connection When connecting to a three-conductor circuit, if local codes permit: or vehicle, branch a. Connect the bare oven ground conductor with the crimped neutral (white) lead to the branch circuit neutral (white or gray in color), using a wire nut.
Installation Instructions lcl Securing the Oven in the Opening I_ Sliding the Oven Into the Drilling the Pilot Holes and Mounting the Oven Opening a. Loop (do not tie) a 36" (91 cm) string around the conduit before the oven is slid into place. This will keep the conduit from falling behind the oven. NOTE: Before drilling the pilot holes, make sure the oven is pushed as far back into the opening as it will go and centered.
Installation Instructions Installing the Metal Bottom Trim Preparing for the Bottom Trim Installation a. With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening. b. Using the trim as a template, mark the center of each slot (two total) where the mounting holes will be drilled. c. Remove the trim. d. Drill pilot holes into the center of each template mark. a. For 27" (68.6 cm) Place the bottom metal trim centered over the pre-drilled mounting holes.
Installation Instructions 151Replacing the Oven Door NOTE: The oven door is heavy. You may need help lifting the door high enough to slide it into the hinge slots. Do not lift the door by the handle. I-_ Open the oven door as far as it will open. r-_ Push the hinge locks up against the front frame of the oven cavity, to the locked position. i Hinge in Locked Position Lift the oven door by placing one hand on each side. The door is heavy, so you may need help. Do not lift the door by the handle.
Installation Instructions Pre-Test Checklist I_ emove all protective and any stickers. I_ heck to be sure that all wiring is secure and not pinched or in contact with moving parts. Check that the bottom trim is installed properly (see page 17). film, if present, Check to be sure the mounting screws are installed and flush with the side trim (see page 16). t Operation Checklist Remove all items from the inside of the oven. I&_ Check that conduit is securely connected to the junction box.
Notes 20
