Owner Manual

36 49-60792 Rev. 3
AT-2
LOCATING THE ANTI-TIP
FLOOR BRACKET (cont.)
5HFRPPHQGHG,QVWDOODWLRQ
Wood
5HFRPPHQGHG,QVWDOODWLRQ
Concrete
Minimum Acceptable #1
Wall Plate Stud
Minimum Acceptable #2
±:RRG)ORRU
Minimum Acceptable #3
±&RQFUHWH)ORRU
)LJXUH± $FFHSWDEOH6FUHZ3ODFHPHQW
Locations
&21&5(7(:DOODQG)ORRU&RQVWUXFWLRQ
$QFKRUVUHTXLUHGQRWSURYLGHG
HDFK´PP[´PPODJEROWV
HDFK´PP2'VOHHYHDQFKRUV
'ULOOWKHUHFRPPHQGHGVL]HKROHVIRUWKH
anchors into the concrete at the center of the
holes marked in Step 2.
,QVWDOOWKHVOHHYHDQFKRUVLQWRWKHGULOOHGKROHV
Place the anti-tip floor bracket as indicated in Step
2. Remove the locator template from the floor.
,QVWDOOWKHODJEROWVWKURXJKWKHDQWLWLSIORRU
bracket and tighten appropriately.
:22':DOODQG7,/()ORRU&RQVWUXFWLRQ
)RUWKLVVSHFLDOFDVHORFDWHWKHZDOOKROHV
LGHQWLILHGLQ)LJ'ULOODQDQJOHG´PP
SLORWKROHDSSUR[DVVKRZQLQ)LJLQWKH
center of each hole.
Mount the anti-tip floor bracket using the
0LQLPXP$FFHSWDEOH,QVWDOODWLRQDV
LOOXVWUDWHGLQ)LJ
C
B
AT-3
ANTI-TIP BRACKET
INSTALLATION
:22':DOODQG)ORRU&RQVWUXFWLRQ
'ULOOWKHDSSURSULDWHQXPEHURI´PP
pilot holes in the center of each floor bracket
hole being used (a nail or awl may be used if
DGULOOLVQRWDYDLODEOH$1'UHPRYHWKHORFDWRU
template from the floor.
Mount the anti-tip floor bracket by fastening the
2, or recommended 4, #10-16 hex-head screws
WLJKWO\LQWRSODFHDVLOOXVWUDWHGLQ)LJXUH
A
AT-4
POSITIONING THE
REFRIGERATOR TO ENGAGE
THE ANTI-TIP FLOOR AND
BASE BRACKETS
Before pushing the refrigerator into the opening,
plug the power cord into the receptacle and
FRQQHFWZDWHUOLQHLIHTXLSSHG&KHFNIRUOHDNV
Locate the refrigerator’s RH side and move back
approximately in line with the RH side of the
cabinet opening, W. This should position the
anti-tip floor bracket to engage the anti-tip base
bracket on the refrigerator.
Gently roll the refrigerator back into the cabinet
opening until it comes to a complete stop.
Check to see if the refrigerator front lines up
ZLWKWKHFDELQHWIURQWIDFH,IQRWFDUHIXOO\URFN
the refrigerator forward and backward until
engagement occurs and you notice that the
refrigerator is fully pushed up against the rear wall.
If Applicable:$GMXVWWKHUHDUDQGIURQWZKHHO
height settings to fully engage the rear anti-tip
brackets, while also aligning the refrigerator
front with the cabinet front face.
A
C
B
'
)LJXUH± $WWDFKPHQWWR:DOODQG)ORRU
NOTE:,I\RXSXOOWKHUHIULJHUDWRURXWDQG
away from the wall for any reason, make sure
the anti-tip floor bracket is engaged when the
refrigerator is pushed back against the rear wall.
Rear RH Corner
of the Refrigerator
)ORRU
Wall
Plate
Stud
)ORRU
Bracket
2 Screws
Must Enter
Wood or
Metal Stud
Wall
Installation Instructions
INSTALLING THE REFRIGERATOR (Cont.)
Anti-Tip Floor Bracket Installation
(Models PYE, GYE, GYS, DYE, PWE, and ZWE only)
INSTALLATION INSTRUCTIONS