Installation guide

CUTOUT FOR DOUBLE OVENS 12THERMAL OVENS1
NOTE: If the cabinet does not have a front frame and the sides are less than sA" (1.9 cm)
both sides equally to establish the cutout i=ldth.
_AL,I_ "1 Junction _ B """"""'_
, . Box
r ,, l Location
' I (junction
', I / boxmay
! I /beloca/ed
.......... '._ I --in adjacent
cabinet}
E _
J
. - "" Cu{ou/Depth
:--_'-_ 23-i/2"
_(597 crn} Min
t
F
D .=.._ ,,l==
G
t
hick, shim
k--
Dim. Description 27" Double Oven 30" Double Oven with 30" Double Oven
Pedestal without Pedestal
A Cabinet Width 27" (68.6 cm) 30" (76.2 cm) 30" (76.2 cm)
B Cutout Width 25" (63.5 cm) min. 28½" (72.4 cm) min. 28½" (72.4 cm) min.
25½" (64.1 cm) max. 28%" (72.7 cm) max. 28%" (72.7 cm) max.
C Cutout Height 491¼d' (126.2 co) min. 511__d' (131.6 cm) min. 50 l/j, (127.64cm)
50½" (127.3 cm) max. 51_d ' (131.9 cm) max.
D Overlap of Oven 1" (2.5 co) _/' (1.75 cm) _/' (1.75 cm)
Over Side Edges
of Cutout
E Clearance to 23" (50.8 cm) min. 23" (53.3 cm) min. 23" (53.3 cm) min.
Adjacent Corners,
Drawers, Wails, etc.,
When Door Is Open
F Overlap of Oven 1" (2.5 co) min. 1" (2.5 cm) min. 1" (2.5 cm) min.
Top of Cutout (1½" {3.2 co) for PT9550, (1½" {3.2 co) for PT9550,
ZET2S and ZET2P) ZET2S and ZET2P)
G Overlap of Oven 1" (2.5 co) min. 1¼" (3.2 cm) 1¼" (3.2 cm)
Bottom of Cutout
H `junction Box 8¾" (22.2 cm) max. 9½" (24.1 cm) max. 9½" (24.1 cm) max.
Location right side only right side only right side only
,j Height to Bottom 44" (111.8 cm) 47" (119.4 cm) 47" (119.4 cm)
of.Junction Do×
K Recommended 13½" (33.7 cm) 12" (30.5 co) 12" (30.5 cm)
Cutout Locution
from Floor
Continue to Section 3,
CUTOUT FOR INSTALLATION OVER A WARMING DRAWER
NOTE: Install the over] only with specific models listed on the label located on top of the over].
NOTE: Additional clearances between cutouts may be required. Check to be sure the oven supports
above the Warming Drawer location do not obstruct the required interior depth and height.
When installing a Warming Drawer below a single or double oven, a separate 120V, 60 HZ, properly
grounded receptacle must be installed. Refer to installation instructions packed with
the Warming Drawer for specific installation requirements.
Anti-Tip Block Against
Rear Wall Per Warming
Drawer Requirement
T
2" (5.1 era)
Min.
Per Warming
Drawer
Requirement
Continue to Section 3 for DWO with Pedestal. Otherwise, continue to Section 4.
J 31-10979 J 0714 GE