Installation guide

ManualsBrandsGE ManualsWall oven/microwave comboOfficial GE microwave/double oven combo

Installation

Instructions

27" Built In Wall Oven/with

Microwave

JKP85

"If you have questions, call 800-GE-CARES orvisit our website at:

www. GEAppliances.com"

Before you begin

Read these instructions carefully and completely

• IMPORTANT-Save these instructions for

local inspector's use.

• IMPORTANT-Observe all governing

codes and ordinances.

• Note to Installer- Be sure to leave these

instructions with the consumer.

• OWNER- Keep these instructions for future

reference.

• ATTENTION INSTALLER!!

All electric wall ovens must be hard wired

(direct wired) into an approved junction

box. A "plug and receptacle" is NOT

permitted on these products

• NOTE- This appliance must be properly

grounded.

Parts Included

8 flat head screws side trim

3 Pan head screws bottom trim

Bottom Trim

Materials Needed

Strain Relief

Clamp

_¢_ WireNu_ts

Junction

Box

36" of String

Tools You Will Need

1/8" Drill Bit & Phillips

Electric or Screwdriver

Hand Drill

Pub. No. 31-10480

229c4053P460 1

Summary of content (12 pages)

PAGE 1
Installation Instructions 27" Built In Wall Oven/with Microwave JKP85 "If you have questions, call 800-GE-CARES or visit our website at: www. GEAppliances.com" Before you begin • ATTENTION INSTALLER!! All electric wall ovens must be hard wired (direct wired) into an approved junction box. A "plug and receptacle" is NOT permitted on these products • NOTE- This appliance must be properly grounded.
PAGE 2
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Electrical For Your Safety Requirements This appliance must be supplied with the proper voltage and frequency, and connected to an individual properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on rating plate. (Rating Plate is located on oven side trim.) We recommend you have the electrical wiring and hookup of your oven connected by a qualified electrician.
PAGE 3
Installation Instructions Pre-Installation Remove packaging materials. Check behind hinges, and under false bottom. Remove labels on the outside of the door, plastic on trims and panel, and all tape around oven. Checklist Door Removal is not a requirement for installation of the product, but is an added convenience. Open the oven door as far as it will go. Push both hinge locks down toward the door frame, to the unlocked position. This may require a flat blade screwdriver. Hinge _.
PAGE 4
Installation Instructions 1_ Place the the ovencutout on a opening. table or platform even with (Platform must support 275 Ibs.) Iq_" Remove the bottom trim from the top of the oven. It will be installed at the end of installation. The trim is wrapped separately and taped to the top of the unit.
PAGE 5
Installation Instructions Cutout for Built-In Oven W/Microwave JUNCTION BOX LOCATION CABINET Cabinet CUTOUT WIDTH 25" MIN. 25 1/4" MAX. Cutout Depth .23 1/2" Cutout Width ..25" .... CUTOUT 2" x 4" or _ equivalentt runners Allow a minimum of 20" for clearance to adjacent corners, drawers, walls, etc. when doors are open HEIGHT 41 1/8" MIN. MAX. _[ ........................ 25 1/4" Max. Cutout Height ........................ 41 1/8" Min. 41 1/4" Max. Overall 41 5/8" Height Overall Width ..
PAGE 6
Installation Instructions Electrical Connections ATTENTION All electric Turn off the circuit breaker to the oven branch circuit. INSTALLER!!! wall ovens must be hard wired or remove fuses With the oven in front of the cabinet (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. opening, on a table or platform, connect the flexible conduit to the electrical junction box as shown below.
PAGE 7
Installation Instructions Electrial Connections NEW CONSTRUCTION AND FOUR-CONDUCTOR BRANCH CIRCUIT CONNECTION cont. OR Three-Conductor Branch Circuit Connection • When installing in a new construction, or • When installing oven in a mobile home, or • When local codes do not permit grounding through neutral: When connecting to a 3-conductor circuit, if local codes permit: branch a.
PAGE 8
Installation Instructions Placing the Oven in the Opening Drilling the Pilot Holes IC-_ Sliding the Oven Into the Opening. a. Loop (do not tie) a 36" string around the conduit before the oven is slid into place. This will keep the conduit from falling behind the oven. Note: Before drilling the pilot holes make sure the oven is pushed as far back into the opening as it will go and centered. Pull out on string loop while pushing the oven into the cabinet a.
PAGE 9
Installation Instructions Replacing the Oven Door Preparing for the bottom Trim Installation a. With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening. b. Using the trim as a template mark the center of each slot (three total) where the mounting holes will be drilled. The oven door is heavy. You may need help lifting the door high enough to slide it into the hinges slots. Do not lift the door by the handle. placing one hand on each side.
PAGE 10
Installation Instructions PRE-TEST CHECK LIST Remove all protective film if present, and any stickers. Check that the bottom trim is installed _ properly (see page 9). Chec to sure that allwi in0 is Check to be sure the mounting screws are installed and flush with the side trim, (see page 9). secure and not pinched or in contact with moving parts. _ Operation Checklist [_ emove all items from the inside of the oven. I_ Checkthat conduit is securely connected to the junction box.
PAGE 11
NOTES 11
PAGE 12
Pub. No.