Installation guide

ManualsBrandsGE Manualswall ovenOfficial GE wall oven

Installation

Instructions

27" Built-In Wall Oven

JKP20, JKP25, JKP28, JKP48, JKP50, JK915,

JK955, JKS06, ZEK938, ZEK958

If you have questions, call 1.800.GE.CARES or visit our website at:

www.GEAppliances.com

Before You Begin

Read these instructions carefully and completely.

• IMPORTANT-save these

instructions for local inspector's use.

• IMPORTANT-observe a,

governing codes and ordinances.

• Note to Installer--Be sure to leave these

instructions with the consumer.

• Note to ConsumermKeep these

instructions for future reference,

• Proper installation is the responsibility

of the installer and product failure due

to improper installation is NOT covered

under warranty.

• NOTE--This appliance must be properly

grounded.

• ATTENTION INSTALLER

All electric wall ovens must be hard wired

(direct wired) into an approved junction

box. A plug and receptacle is NOT permitted

on these products.

Parts Included

Screws for

Installation

Metal

Bottom Trim

Optional

Metal Bottom Trim

Plastic

Bottom Trim

Optional

Metal Bottom

Trim Assembly

(on some models)

Materials Needed

4__ _o WireNu_t S

Strain Relief Clamp Junction

for 1/2" conduit Box _£. _

36" of String

Tools Needed

1/8" Drill Bit and

Electric or Hand Drill

Phillips

Screwdriver

220c4053P504-4

31-10523-4 06-04JR

Summary of content (16 pages)

PAGE 1
Installation Instructions 27" Built-In Wall Oven JKP20, JKP25, JKP28, JKP48, JKP50, JK915, JK955, JKS06, ZEK938, ZEK958 If you have questions, call 1.800.GE.CARES or visit our website at: www.GEAppliances.com Before You Begin Read these instructions carefully and completely. • IMPORTANT-save instructions these for local inspector's use. • IMPORTANT-observe a, governing codes and ordinances. • Note to Installer--Be sure to leave these instructions with the consumer.
PAGE 2
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Electrical Requirements For Your Safety • Be sure your oven is installed properly by a qualified installer or service technician. This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on rating plate. (Rating Plate is located on oven side trim.
PAGE 3
Installation Instructions Pre-lnstallation Checklist ALL INSTALLATION INFORMATION ON THE FOLLOWING PAGES IS TO BE USED FOR SINGLE AND DOUBLE OVEN INSTALLATION! Door removal is not a requirement for installation of the product, but is an added convenience. To remove the door: Open the oven door as far as it will go. Remove packaging materials. Check behind hinges and under false bottom. Remove labels on the outside of the door, plastic on trims and panel and all tape around oven.
PAGE 4
Installation Instructions [_ Pre-lnstallation Checklist cont. [_ Remove the bottom trim from the top of the oven. It will be installed at the end of the installation process. The trim is wrapped separately and taped to the top of the unit. lace the oven on a table or platform even with the cutout opening. (Platform must support 150 Ibs. single, 275 Ibs. double.
PAGE 5
Installation Instructions Cutout for Sin le Built-In Oven Cabinet Width 27" Allow 718" for overlap of oven over side edges of cutout ----..._ Cabinet Junction Box Location Cutout Width - 25" Min. 25 1/4" Max. 2" x 4" or 22" Min. above base rail Cutout equivalent runners level with bottom o1 cutout Height 27 5/8" Min. 28 1/8" Max. I I I Width 27" Recommended Minimum Cutout Location from Floor 32 1/2" Cutout Depth 23 1/2" Min. Cutout Width 25" Min. 25 1/4" Max. 27 5/8" Min.
PAGE 6
Installation Instructions Cutout for Double Built-In Oven Cabinet Junction Box Location Width Cabinet 27" Allow 7/8" for overlap of oven over side edges __ Cutout Width 25" Min. 25 1/4" Max. Width 27" Recommended Minimum Cutout Location from Floor 13 114" Cutout Depth 23 5/8" Min. Cutout Width 25" Min. 25 1/4" Max. _ 44" Above base rail Cutout Height Cutout Height 49 11/16" Min. 50 1/8" Max. 49 11/16" Min. 50 1/8" Max.
PAGE 7
Installation Instructions Cutout for Single Built-In Oven Under Counter Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models. \ 240V / 208V Junction Box Location Top and/or side fillers may be necessary if unit is positioned between existing cabinets. Be sure they are attached securely, since they will anchor the oven in the cabinet.
PAGE 8
Installation Instructions Electrical Connections ATTENTION Turn off the circuit breaker or remove fuses to the oven branch circuit. INSTALLER All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. With the oven supported on a table or platform in front of the cabinet opening, connect the flexible conduit to the electrical junction box as shown below.
PAGE 9
Installation Instructions IBI Electrical Connections New Construction and Four-Conductor Branch Circuit Connection • When installing in new construction, • When installing in a mobile home, or • When installing in a recreational Three-Conductor Branch Circuit Connection When connecting to a three-conductor circuit, if local codes permit: or vehicle, cont branch a.
PAGE 10
Installation Instructions Securing the Oven in the Opening Sliding the Oven Into the Opening Drilling the Pilot Holes and Mounting the Oven a. Loop (do not tie) a 36" string around the conduit before the oven is slid into place. This will keep the conduit from falling behind the oven. NOTE: Before drilling the pilot holes, make sure the oven is pushed as far back into the opening as it will go and centered.
PAGE 11
Installation Instructions To install a single metal bottom trim assembly (on some models), use sections C3 and C4. To install a metal bottom trim with a plastic bottom trim (on some models), use sections C3-C5. Preparing for the Bottom Trim Installation Installing the Plastic Bottom Trim (on some models) a. With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening. b.
PAGE 12
Installation Instructions 151Replacing the Oven Door NOTE: The oven door is heavy. You may need help lifting the door high enough to slide it into the hinge slots. Do not lift the door by the handle. = _'-_ Open the oven door as far as it will open. _"_ Push the hinge locks up against the front frame of the oven cavity, to the locked position. / Hinge in Locked Position Lift the oven door by placing one hand on each side. The door is heavy, so you may need help. Do not lift the door by the handle.
PAGE 13
Installation Instructions Pre-Test Checklist [_ emove all protective and any stickers. [_ Check to be sure that all wiring is secure and not pinched or in contact with moving parts. Check that the bottom trim is installed properly (see page 11). film, if present, [_ Check to be sure the mounting screws are installed and flush with the side trim (see page 10). Operation Checklist Remove all items from the inside of the oven.
PAGE 14
NOTES 14
PAGE 15
NOTES 15
PAGE 16
NOTES 16