) 466-2061 Rev C June 2004 *( 6HFXULW\ ZZZ *( 6HFXULW\ FRP Part Number: 60-960-95 T e s t S y s te m W e e k ly O ff S ta y A w a y 1 2 3 N o D e la y S ile n t A p re s s b o th 4 5 6 F e a tu re s S y s te m M e n u B p re s s b o th 7 8 9 S ta tu s L ig h ts B y p a s s 0 # C Q u ic k E x it D p re s s b o th * S y s te m is O K A rm e d R e a d y Q u ic k G u id e D is a r m S y s te m / C a n c e l A la r m B y p a ss S e n so rs P ress 1 + C O D E .
Notices FCC Part 15 Information to the User Changes or modifications not expressly approved by GE Security can void the user’s authority to operate the equipment. FCC Part 15 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference in a residential installation.
Contents About This Manual 1 Special Installation Requirements .............................................................................................................. UL Listed Installations............................................................................................................................ SIA System Requirements ...................................................................................................................... Central Station Reporting ...................
SuperBus 2000 8Z Input Module (60-774)........................................................................................... SuperBus 2000 4-Relay Output Module (60-770)................................................................................ SuperBus 2000 Cellular Backup Module ................................................................................................. SuperBus 2000 Automation Module (60-783-02) ..............................................................................
Changing Fixed Display LCD Touchpad Chime and Trouble Beep Tones ............................................. Adjusting Touchpad Display Contrast ..................................................................................................... Testing Audio Verification Module (AVM) Communication .................................................................. Testing Cellular Backup Communication ................................................................................................
About This Manual This manual provides information for planning, installing, programming, and testing this security system. When necessary, this manual refers you to other documentation included with compatible peripherals. Planning sheets are included for you to record hardware layout and software programming settings. About the User’s Guide The User’s Guide (466-2060) contains user worksheets that should be filled out during the installation and programming of the system.
• • • • • • • • • Immediate Beeps set to on UL 98 Options set to on Receiver Failure set to on (if wireless devices are used) Siren Verify set to on RF TX Timeout set to 4 hours (if system includes a built in or SuperBus 2000 RF Receiver and wireless smoke sensors) Sleep Time set to off Siren Timeout set to 4 minutes or more Two Trip Error set to off Disable Trouble Beeps set to off UL 1023 & 985 24-Hour Backup For 24-hour backup, the total current draw for all connected devices is limited to 190 mA (dur
Function Operation Cancel Alarm Enter Code Only (or 1 + CODE) Abort Annunciation Enabled Cancel Report Annunciation Enabled UL 1635 Digital Alarm Communicator System Note For UL 1635 installations, Entry Delay plus Dialer Abort Delay must not exceed 60 seconds. Same as UL 1023 & 985 plus: • • • • • • • • • AC Failure set to on Comm Failure set to on RF Tx Timeout set to 4 hours Low CPU Battery set to on Phone Number must be programmed Next Phone Test set to 1 Phone Test Freq.
• Up to 96 wireless or hardwired zones Standard Panel The following describe the basic panel (out-of-box) hardware capabilities. • • • • • • • • • • • • Power: Input for an AC step-down, plug-in style transformer. Auxiliary Power Output: Output that supplies 8.5 to 13.5 VDC with up 1.35 amps (with panel powered by 50 VA transformer) for bus devices and hardwired detectors, such as smoke and motion detectors. Bus A and B: Input and output that provides communication between bus devices and the panel.
• • 4 Output SnapCard: Provides four form C relay outputs that can be set up to activate other signalling devices, based on system events, schedules, or direct control. 4Z Input/2 Output Combo SnapCard: Provides three hardwire zone inputs, one two wire smoke detector loop, and two outputs that can be set up to activate other signalling devices, based on system events, schedules, or direct control. SuperBus 2000 8Z Input Module (HIM) Provides eight additional hardwire zone inputs.
Note (A) Class 2, Class 3, and power-limited fire alarm circuits must be installed using FPL, FPLR, FPLP, or substitute cable permitted by the National Electrical Code ANSI/NFPA 70. Wire that extends beyond the cable jacket must be separated from all other conductors by a minimum of 1/4-inch or by a nonconductive barrier.
Table 1: Maximum Device Wire Length and Current Draw (Continued) Max. Wire Length to Panel Device Max. mA Draw 8Z Hardwire Zone Expander SnapCard N/A 230 mA* 4 Output SnapCard N/A 130 mA* SuperBus 2000 8Z Input Module 22 ga.—1,800 ft. 18 ga.—4,000 ft. 35 mA SuperBus 2000 4-Relay Output Module 22 ga.—350 ft. 18 ga.—900 ft. 180 mA SuperBus 2000 Energy Saver Module 22 ga.—1,600 ft. 18 ga.—4,000 ft. 20 mA Standard Power: 22 ga.—15 ft. 18 ga.—40 ft. 1600 mA High Power 22 ga.—10 ft. 18 ga.
Table 3: Minimum Device Current Draw Device Min. mA Draw SuperBus 2000 Automation Module 30 mA SuperBus 2000 Transceiver Module 50 mA SuperBus 2000 Wireless Gateway Module 55 mA Interrogator 200 10 mA Interrogator AVM 45 mA After determining panel location, run all necessary wires to that location using the guidelines in Table 4.
Mounting Hole ID : X X X X X X X X SuperBus 2000 Transceiver Panel Circuit Board (under Transceiver) Knockout Knockout Phone Interface/ Voice Module Mounting Holes Figure 2. Mounting the Panel Identify Panel Components Before installing devices and making wiring connections, familiarize yourself with the main panel components. Figure 3 shows the three main panel components: the circuit board, transceiver and phone interface/voice module.
Connect To Inside Terminals ID : X X X X X X X X Transceiver Figure 4. Installing the Antennas Note For best results, it is recommended that you crimp a spade lug on the wire end at the panel and secure the lug under the circuit board screw as shown in Figure 5. Connecting the Panel to Earth Ground For maximum protection from lightning strikes and transients, connect the lower-left circuit board screw to earth ground as shown in Figure 5.
Note The panel comes with factory programmed onboard hardwire zones. Install 2k-ohm, end of line (EOL) resistors on all unused factory programmed onboard hardwire zones. If you don’t want to install EOL resistors, delete any unused zones from memory. See Table 8 for onboard hardwire zone factory programming. Connecting Detection Devices to Panel Zone Inputs Zone inputs 1 through 8 are supervised using included 2k-ohm, end-of-line resistors at the last device on each circuit.
Note The Two-Wire Smoke setting (in program mode) must be off when using 4-wire smoke detectors. See ONBOARD OPTIONS—INPUTS in the section “Programming the Panel” for complete details. 2-Wire 4-Wire +12V Zone Z O N E + 1 2 V 2W 2 W S SMK M K 88 Panel 2 Terminals 222 Panel Terminals 2 23 3 Model 449AT + - - Model 449AT + 2k Ohm EOL Resistor 49-454 (Locate at Last Detector) 2k Ohm EOL Resistor 49-454 (Locate at Last Detector) Figure 8.
Hardwire Interior Speaker (60-528) For interior siren applications. Connect the speaker to the panel as shown in Figure 9. ! Connect only the large speaker to the panel terminals 7 and 8 as shown. The smaller speaker cannot handle to output of terminals 7 and 8. To avoid damaging the speaker, the smaller speaker should not be connected to terminals 7 and 8. Caution Connect two units to the panel terminals with speakers in series (16-ohms), as shown in Figure 10.
(01710) activates the output for status and alarm tones, allowing for a piezo siren connection without changing the output configuration number. It is typically used for interior siren application. For more information on output configuration numbers, see “Onboard Options Menu”. Note Piezo siren connections to terminal 10 require a 2k resistor that can be located at the panel, since it does not supervise the circuit.
Note Regardless of supervised or unsupervised siren installation, you must follow the order of installation as described to avoid learning the wrong (or undesired) House Code and SWS Supervision Code into siren memory. Note When installing Supervised Wireless Sirens for supervised operation, be sure to program sensor text that clearly identifies each siren. For example, HALLWAY SIREN or BASEMENT SIREN. This can help both you and your customer locate a specific siren if a problem occurs.
Connecting Alphanumeric and Fixed Display Touchpads Alphanumeric and Fixed Display touchpads use the same color-coded wire scheme. Connect the touchpads to the panel power output and bus terminals as shown in Figure 14. GND +12V SuperBus 2000 Fixed Display Touchpad or LCD Alphanumeric Touchpads 4 A BUS B 5 6 +12V/Red Bus A/Green Bus B/White GND/Black 3 Figure 14. Wiring Touchpads Installing SuperBus 2000 Modules SuperBus 2000 modules can be installed inside the panel cabinet or away from the panel.
Phone Interface/Voice Module Terminal Strip B 3 4 G N D 5 G N D 8 9 1 0 A U D 1 A U D 2 G N D 1 1 T IP 1 Grn Brn Gry Red 2 4 2 5 2 6 2 7 Green Panel Terminals 6 7 S P K 1 S P K 2 1 2 T IP 2 1 3 R IN G 2 1 4 R IN G 1 Red 2 Gray A Brown 1 + 1 2 V DB-8 Cord Plug Brn Gry Grn Red RJ-31X Jack 6 0 7 3 4 1 0 9 d .d s f Figure 16.
SuperBus 2000 8Z Input Module (60-774) Connect the SuperBus 2000 8Z Input Module to the panel as shown in Figure 19. Connect all necessary input wiring using the Installation Instructions included with module. SuperBus 2000 4-Relay Output Module (60-770) Connect the SuperBus 2000 4-Relay Output Module to the panel as shown in Figure 19. Connect all necessary output wiring using the Installation Instructions included with the module.
Automation Module Circuit Board DB-9 Serial Cable Automation Device 1 2 3 4 5 6 Z C O M Z O N E 1 G N D + 1 2 V 3 4 B U S A 5 B 6 Panel Terminals 6 0 7 3 4 g 3 0 6 d d s f Figure 21. Connecting the SuperBus to the Panel SuperBus 2000 Wireless Gateway Module (60-861) Connect the SuperBus 2000 Wireless Gateway Module to the panel as shown in Figure 22.
• If an analog line is not available, contact a telecommunications specialist and request an analog line off the phone switch (PBX mainframe) or a 1FB (standard business line). ¾ To connect a phone line to the panel using an RJ-31X/CA-38A jack (see Figure 23): 1. Run a 4-conductor cable from the TELCO protector block to the jack location. 2. Connect one end of the cable to the jack (see B in Figure 34). 3.
Powering Up the Panel After connecting and wiring all devices to the panel, you are ready to apply AC and backup battery power to the panel. The panel comes with the backup battery leads already connected to the lugs on the panel. ¾ To power up the panel: 1. Connect the red and black battery leads not already connected to the lugs on the panel to the battery terminals (see Figure 24). 2. Plug the transformer into an outlet that is not controlled by a switch.
Touchpad Button Programming Functions In program mode, touchpad buttons let you navigate to all installer programming menus for configuring the system. Table 6 describes the touchpad button functions in program mode. Table 6: Touchpad Button Functions Button Programming Function # Selects menu item or data entry. * Deselects menu item or data entry (if pressed before #). A&B Scroll through available options at the current menu tier.
Again, arrows pointing right represent pressing B to advance forward through the menus. Pressing A moves through the menus in reverse. Arrows below each menu represent pressing # to advance to those settings that pertain to that menu. Only when a specific menu is displayed can you advance to those settings. For example, from the SENSORS menu pressing # gives you access to learning sensors, programming sensor text, deleting sensors, and viewing/editing sensor programming.
Clear Memory (System Programming) Note Clearing the memory will erase onboard hardwire zone factory programming. Clearing memory deletes all existing programming information (except the Dealer Code). ¾ To Clear Panel Memory: 1. With the system in program mode, press A or B until the display shows CLEAR MEMORY. 2. Press # and the display shows ENTER CODE TO CLEAR MEMORY. 3. Enter the 4-digit installer or dealer code (if programmed) + #.
Security-Global (Default = none) Dealer Code (0002) The 4-digit dealer code is used to prevent unauthorized persons ¾ To program a Dealer Code: from changing the programmed central station phone numbers. 1. With the display showing DEALER CODE ****, enter the When this feature is enabled, central station phone numbers desired 4-digit code. The display flashes the entered cannot be changed (unless you enter the program mode by code. using the dealer code). All other system settings are still acces- 2.
Quick Exit (partition 1: 0012, partition 2: 0022) Security-Partition 1-2 (Default = on) This setting determines whether or not users can open and close a standard entry/exit door without causing an alarm (while the system is armed). ¾ To turn Quick Exit off or on: 1. With the display showing QUICK EXIT OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting.
Keyswitch Sensor (partition 1: 0015, partition 2: 0025) Security-Partition 1-2 (Default = none) This feature lets users arm and disarm the system using either a keyswitch wired to a hardwire zone input or a wireless door/window sensor. ¾ To assign a Keyswitch Sensor: 1. With the display showing KEYSWITCH SENSOR nn (current sensor number), enter the desired sensor number (01–96). The display flashes the entered sensor number. 2. Press # and the display shows the new number.
Phone Number (cs phone 1: 0100, cs phone 2: 0110, cs phone 3: 0120) Phones-CS Phone 1-3 (Default = none) This setting is used for programming the central station receiver phone number. Phone numbers can be 1 to 24 digits long, including pauses or * and # characters. ¾ To program a Central Station Phone To enter pauses, press C. To enter *, press and hold 7 for about two seconds. To enter #, press and hold 9 for about two seconds.
Exception Rpts (cs phone 1: 0103, cs phone 2: 0113, cs phone 3: 0123) When this setting is on, the panel reports to the central station if the system is not armed or disarmed at the specified schedule times. Open/Close Rpts (cs phone 1: 0104, cs phone 2: 0114, cs phone 3: 0124) Phones-CS Phone 1-3 (Default = off) ¾ To turn Exception Reports off or on: 1. With the display showing EXCEPTION RPTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2.
Cellular Backup (cs phone 1: 0107, cs phone 2: 0117, cs phone 3: 0127) This setting determines whether the panel uses cellular communication for reporting if attempts using a landline are unsuccessful. Phones-CS Phone 1-3 (Defaults: CS Phone 1 = on, CS Phone 2&3 = off) ¾ To turn Cellular Backup off or on: 1. With the display showing CELLULAR BACKUP, press 1 (for off) or 2 (for on). The display flashes the entered setting. 2. Press # and the display shows the new setting.
Exception Rpts (pager 1: 0133, pager 2: 0143, pager 3: 0153, pager 4: 0163, pager 5: 0173) Phones-Pager Phone 1-5 (Default = off) This setting determines whether the panel reports to a pager if the system is not armed or disarmed at the specified schedule times, if open/close reports are turned on. ¾ To turn Exception Reports off or on: 1. With the display showing EXCEPTION RPTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2.
Phones-Downloader Phone (Default = none) Phone Number (0180) Use this setting to enter the phone number of an off-site computer that can be used to program the panel through the phone line. Phone numbers can be 1 to 24 digits long, including pauses or * and # characters. Note Call-waiting services should be disabled to prevent interrupting panel communication to the downloader. To program a dialing prefix that disables call-waiting, see the Call Wait Cancel setting under the menu PHONE OPTIONS—GLOBAL.
Phone Options-Global (Default = on) Comm Failure (02003) This setting determines whether the panel activates trouble beeps to alert users on the premises that communication to the central station failed. Failure notification occurs after the third unsuccessful reporting attempt to the central station/pager. If a Phone Supervision Card (60-789) is installed, failure notification can occur immediately if inadequate phone line voltage is detected upon the initial dialing attempt.
Phone Options-Global (Default = 15 sec.) Pager Delay (02008) This setting determines how long a report is delayed to a pager, after the panel dials the pager number. Note The Pager Delay time should not be set below 5 seconds, unless absolutely necessary. ¾ To set the Pager Delay time: 1. With the display showing PAGER DELAY nn SECS (current setting), enter a delay time (0–30). The display flashes the entered setting. 2. Press # and the display shows the new setting.
Ring/Hang/Ring (partition 1: 0212, partition 2: 0222) Phone Options-Partition 1-2 (Default = on) This setting determines how the panel picks up (seizes) the phone line. Select “on” if an answering machine shares the phone line with the panel. Select “off” if there is no answering machine sharing the phone line with the panel. ¾ To turn Ring/Hang/Ring access off or on: 1. With the display showing RING/HANG/ RING OFF/ON (current setting), press 1 (off) or 2 (on).
Phone Access Key (partition 1: 0216, partition 2: 0226) Phone Options-Partition 1-2 (Default = #) ¾ To change the Phone Access Key: 1. With the desired partition selected, press A or B until the display shows PHONE ACCESS KEY If the Local Phone Control feature is enabled, the user can pick up the #/* (current setting). phone and press # (within 5 seconds) to access the security system. The 2. Press 1 (for *) or 2 (for #).
Timers-Global (Default = 7 days) Next Phone Test (0303) This setting is used by the Auto Phone Test feature (see PHONE OPTIONS—GLOBAL) to determine when the next automatic phone test should occur. This setting should be the same as, or less than, the Phone Test Freq. setting. Note For UL 1635 listed installations, this feature must be set to 1. Output Trip Time (0304) ¾ To set the Next Phone Test: 1. With the display showing NEXT PHONE TEST nnn DAYS (current setting), enter the number of days (1–255).
Extended Delay (partition 1: 0312, partition 2: 0322) This setting determines how much time the user has (after arming the system) to enter or exit the premises through a “designated extended delay door” (1–8 minutes). Note For UL Listed installations Extended Delay may not be used. Siren Timeout (partition 1: 0313, partition 2: 0323) This setting determines how long sirens sound (1–30 minutes) if no one is present to disarm the system.
House Code (partition 1: 0401, partition 2: 0411) This setting enables X10 controlled lights to work in a selected partition without interfering with the X10 controlled lights of the other partition. After setting the panel house code for each partition, you must set the X10 controlled lights for that partition to the same house code. The letter that appears automatically after the house code number indicates the necessary HOUSE dial setting for X10 modules in that partition.
Keychain TP Arm (partition 1: 0513, partition 2: 0523) When this setting is on, pressing the lock button on keychain touchpads arms the system directly to AWAY with NO DELAY. When this setting is off, each key-press increments the arming level (i.e., from OFF to STAY, from STAY to AWAY). Star Is No Delay (partition 1: 0514, partition 2: 0524) This setting determines whether the keychain touchpad star button controls an output (off) or the No Delay feature (on).
Low CPU Battery (06004) When this setting is on, the panel reports a low panel battery to the central station before shutting down. Note For UL 1635 listed installations, this feature must be set to on. Battery Restoral (06005) If this setting is on, the panel reports to the central monitoring station when a wireless sensor or touchpad reports a battery replacement to the panel.
Reporting-Global (Default = off) TP Panic RPT FMT (06009) This setting determines how the panel formats touchpad panic alarm reports to the central station. When this feature is turned on, touchpad panic alarms report using the following 3-digit codes: Auxiliary—597, Police—598, Fire—599 ¾ To turn TP Panic RPT FMT off or on: 1. With the display showing TP PANIC RPT FMT OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2.
Reporting-Global (Default = 1) Swinger Limit (06014) This setting determines the maximum number of times (1–2) a sensor or zone can go into alarm (during a single arming period) before the panel automatically bypasses that sensor or zone. This feature only applies to sensors or zones in groups 00–20, 29, 34, or 35. When set to 1, the panel automatically bypasses a sensor or zone after it causes an alarm.
No Activity (partition 1: 06103, partition 2: 06203) Reporting-Partition 1-2 (Default = off) When this setting is on, the panel sends a no activity report to the central ¾ To turn No Activity reports off or on: station when the activity timeout expires (see TIMERS—ACTIVITY TIMEOUT). 1. With the display showing NO ACTIVITY OFF/ ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting.
Freeze Alarm (partition 1: 06107, partition 2: 06207) Reporting-Partition 1-2 (Default = off) This setting determines whether the panel reports a freeze alarm to the central station or pager, when the selected partition’s energy saver module detects a temperature that matches a predetermined setting (see BUS DEVICES—UNIT ID—ENERGY OPTIONS—FREEZE TEMP). ¾ To turn Freeze Alarm reporting off or on: 1.
UL 98 Options (0702) Siren Options-Global (Default = off) This setting determines whether the panel complies with UL 98 requirements (4-hour trouble beep restart, 4-hour backup battery test, 4-hour smoke (group 26) zone supervisory). Note For UL Listed installations, this feature must be on. SWS Supv Code (0703) ¾ To turn UL 98 Options off or on: 1. With the display showing UL 98 OPTIONS OFF/ ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2.
• EDIT SENSORS lets you view and, if desired, change a sensor group or partition assignment. You can also identify whether a zone is wireless or hardwire, whether it is configured as Normally Closed (N/C) or Normally Open (N/O), or if the zone is a touchpad. Table 7: How to Trip Sensors Sensor Steps to Trip Sensor Hardwire Zones Start with the zone in its “normal” state, then trip the zone into its alarm state.
Table 8: Onboard Hardwire Zone Factory Programming Zone Input Group No. & Description 6 13–Instant Perimeter 7 13–Instant Perimeter 8 13–Instant Perimeter Note If the panel memory is cleared, all onboard hardwire zone factory programming will be erased. Sensor Text (081) Sensors (Default = none) ¾ To program Sensor Text: 1. Press A or B until the display shows SENSOR TEXT. Use the item numbers that appear in Appendix B, Table B2 2. Press # and the display shows TEXT FOR SN 01.
Audio Verification Menu The AUDIO VERIFICATION menu lets you set up the audio verification module (AVM) operation in partition 1. If you want audio verification for partition 2, you must install a “stand-alone” audio verification module and a 4-Relay Output Module (HOM) (60-770) output for that partition. The following sections describe the audio verification settings that appear under PARTITION 1.
Audio Verification-Partition 1 (Default = 02 sec.) Beep Delay (0905) This setting determines how long AVM access beeps are delayed (0–300s, in 2-second intervals) at the beginning of a 2-way audio session. ¾ To change the Beep Delay: 1. With the display showing AUDIO VERIFY OFF/ON, press A or B until the display shows BEEP DELAY nn SECS (current setting). 2. Enter the desired time. The display flashes the entered setting. 3. Press # and the display shows the new setting.
Acc. Modules-Bus Devices-Unit ID-Change ID (Default = none) Device ID This menu lets you change the bus device ID number when replacing a defective bus device. ¾ To change a Device ID: 1. With the display showing the desired bus device, press # + #. The display shows DEVICE ID (current ID). 2. Enter the ID of the new bus device. The display flashes the entered selection. Press # and the display shows the new setting. 3. Exit programming mode. 4. Remove AC and battery power from the panel. 5.
Acc. Modules--Bus Device-Unit ID-Keypad Options (Default = on) Key Beeps ¾ To turn Key Beeps on or off: 1. With the display showing the desired touchpad, press # then A or B until the display shows KEYPAD OPTIONS. Next, press # then A or B until the display shows KEY BEEPS OFF/ON (current setting). 2. Press 1 (off) or 2 (on) to select the desired setting. The display flashes the entered selection. 3. Press # and the display shows the new setting.
Output Programming (output 1: 101001, output 2: 101011, output 3: 101021, output 4: 101031) This setting lets you assign a partition and a 5digit configuration number for each SnapCard relay output. This number determines both which system event activates the output and the duration or time the output is activated. 1. 2. Acc.
Onboard Options-Inputs (Default = off) Smoke Verify (1100) This setting controls the number of sensor group 26 (fire) zone trips needed to report a fire alarm. • Hardwire Smokes: will determine whether or not the panel requires two alarm signals within five minutes (on) from 2wire smoke detectors connected to panel zone input 6 and/ or SnapCard zone inputs or any other hardwire zone learned into group 26 (fire) before activating system sirens and reporting to a central station (or pager).
Output Text (Output 1-1120, Output 2-1121) Onboard Options-Output Text-Output 1, 2 (Default = none) ¾ To program Output Text: • Use the item numbers listed in “Appendix B, Table B2” for char- 1. With the display showing ONBOARD OPTIONS, press # then press B twice and the display shows acters and words. OUTPUT TEXT. • If a desired word does not appear in Table B2, create it using the 2. Press # and the display shows OUTPUT 1. characters (custom text). 3.
Time and Date (Default = 00:00) Time (020) This setting lets you adjust the panel clock to the correct time. The panel uses a 24-hour clock. For example, to set the time to 4:17 P.M., enter 1617. ¾ To set the Time: 1. With the display showing TIME AND DATE, press # and the display shows TIME hh:mm (current time). 2. Enter the correct time (0000–2359). The display flashes the entered time. 3. Press # and the display shows the new time. Time and Date (Default = 01/01/00) Date (021) ¾ To set the Date: 1.
Direct Bypassing (030nnn1 where nnn=user number 00-229) User Codes-Reg. User Codes-User NNN (Default = off) This setting determines whether or not a specific user code provides access to the “bypass sensors” feature. Set this feature to “on” for all users who need to be able to bypass sensors. ¾ To turn user code Direct Bypassing off or on: 1. With the display showing USER CODES, press # and the display shows REGULAR USER CODES. 2. Press # and the display shows USER nnn (first available user number). 3.
Latchkey Report (030nnn5 where nnn=user number 00-229) User Codes-Reg. User Codes-User NNN (Defaults: 00-05 = on, 06-229 = off) This setting determines whether or not the user code causes a latchkey report to be sent to a pager when the code is used to change arming levels. ¾ To assign the Latchkey Report attribute to user codes: 1. With the display showing USER CODES, press # and the display shows REGULAR USER CODES. 2. Press # and the display shows USER nnn (first available user number). 3.
Touchpad Brightness (042) Options (Default = 2) This setting lets the user lighten or darken the background on touchpad displays. Each touchpad can be set to compensate for lighting conditions in the touchpad location. ¾ To adjust Touchpad Brightness: 1. Press A or B until the display shows OPTIONS. 2. Press #, then A or B until the display shows TOUCHPAD BRIGHTNESS n (current setting). 3. Enter a setting from 0 (darkest background) to 3 (brightest background). The display flashes the entered selection.
(Default = 00:00) Set Up Schedules (05XXY, where XX=schedule 00 thru 15 and Y=start [0]/stop[1] 0 thru 8-Monday thru Sunday [2-8]) ¾ To set up a Time Schedule: 1. Press A or B until the display shows SET UP SCHEDULES. 2. Press # and the display shows SCHEDULE 00. If you want a different schedNote ule number, press A or B until the desired schedule number appears. If you are programming schedules for your cus3. Press # and the display shows START TIME hh:mm (current setting).
Exception Reports (062nn-Opening, 063nn-Closing, where nn=Schedule number [0 to 15]) This setting lets you attach the Exception Opening report feature and the Exception Closing report feature to time schedules. Lights (064xnn, where nn=Schedule number [0 to 15] and x=light number [1 to 9] minus 1) This setting lets you attach light controls to a time schedule. Outputs (065xnn, where nn=Schedule number [0 to 15] and x=output number [1 to 6] minus 1) This setting lets you attach outputs to a time schedule.
Attach Schedules To Events (Default = off) Arming (0660nn, where nn=Schedule number [0 to 15]) This setting lets you arm according to a time schedule. Note This setting will allow you to arm to AWAY only. There is no disarm schedule. ¾ To Attach Schedules to Arming: 1. Press A or B until the display shows ATTACH SCHEDULES TO EVENTS. 2. Press # then A or B until the display shows ARMING. 3. To select arm to AWAY press #. 4. Press # and the display shows SCHEDULE 00 OFF/ON (current setting).
System Version Menu The SYSTEM VERSION menu lets you view and identify panel hardware and software. This information is primarily used for troubleshooting purposes. (Default = N/A) System Version (010: factory code, 011: system number, 012: system level) This menu lets you view and identify panel hardware and software version. ¾ To view and identify the System Version: 1. Press A or B until the display shows SYSTEM VERSION. 2. Press # and the display shows FACTORY CODE nnn*nnnn. 3.
Table 9: Basic Touchpad Commands (Continued) Command System Response 3 + CODE Arms system to AWAY 2 (quick arm on) Arms system to STAY 3 (quick arm on) Arms system to AWAY 2 or 3 + CODE + 4 or 2 or 3 + 4 Arm system—No Delay (no exit or entry delay) 5 + 2 or 3 + CODE or 5 + 2 or 3 Arms system silently (no arming status beeps) 7+1 Turns chime feature on and off 7+2 Turns Energy Saver on and off 7+6 Identifies alarms in memory 7+7+n (n = output number [1–6]) Turns the output on or off.
For wireless sensors that don’t respond, use an RF Sniffer (60-401) test tool to verify that the sensor is transmitting. Constant beeps from the RF Sniffer indicate a runaway (faulty) sensor. Remove the sensor battery(s) and replace the sensor. Testing Phone Communication Perform a phone test to check the phone communication between the panel and the central monitoring station. ¾ To perform a phone test: 1. Contact the central monitoring station to inform them that you are testing the system. 2.
Table 11: Pager Sensor/Zone Code and Numbers Code Sensor/Zone or User Number 001–096 Sensor/Zone Numbers 1–96 600–829 Regular User Codes 0–229 used 846 System Master Code used 847 Installer Code used 848 Dealer Code used 850 Quick Arm used 851 Keyswitch Sensor used 852 System Armed Itself (during service or power-up) Testing Outputs and Sirens All outputs (onboard and SnapCard) should be tested to verify configuration programming.
Note The system must have highand low-temperature limits set to test the Energy Saver Module. ¾ To test the Energy Saver Module: 1. Press * (status) + * (status) to display the system status, ENERGY SAVER OFF, and the present TEMPERATURE nn°. The temperature displayed (and/or announced) should match the house thermostat. If the temperatures do not match, refer to the ACCESSORY MODULES—BUS DEVICES menu in the “Programming” section.
Testing Cellular Backup Communication Perform this test to check the cellular communication between the panel and the central monitoring station. Note If the current settings do not match the test settings, record the current settings (Table 13), so that they can be restored when this test is complete. ¾ To test Cellular Communication: 1. Contact the central monitoring station to inform them that you are testing the system. 2. Install and activate the SuperBus 2000 Cellular Backup Module. 3.
Feature Problem Action/Solution 1. 2. 3. Check that the backup battery is installed correctly and the AC power transformer is plugged in. Measure the incoming AC voltage at panel terminals 1 and 2. It should read about 24 VAC. Check for 11.75 to 13.5 VDC battery voltage between the backup battery spade lugs. If the battery voltage is not within this range, replace the battery. Note When the panel is running a backup battery test, the reading at the connected battery can range from 11.2 to 13.5 VDC.
Feature Problem Action/Solution System cancels sensor bypass when you try to arm to level 2 or 3. Sensor is being bypassed before arming to 2—STAY or 3—AWAY. Arm to the desired level before bypassing a sensor. Wireless Sensor and Touchpad Batteries System indicates Sensor/Touchpad nn low battery. Replace the indicated device battery. Test the sensor/touchpad after replacing the battery.
Feature Problem Action/Solution 1. 2. 3. Check for correct wiring at speaker and panel terminals; correct where necessary. Speaker output has shut down because panel detected terminal 7 or 8 is shorted to ground. Disconnect panel AC and battery backup power. Locate short and correct. Apply panel AC and backup battery power and retest. Alarm is in partition 2 and speaker is connected to panel terminals 7 and 8, which activate only for partition 1 alarms.
Feature Problem Action/Solution Touchpad indicates [sensor #] supervisory and/or Sensor [sensor #] supervisory is heard. 1. 2. 3. Use an RF Sniffer (60-401) to verify that sensor is transmitting. If sensor is not transmitting, check battery for low or no voltage and replace. Change mounting position of sensor (from horizontal to vertical or vice versa) and test sensor several times for consistency. Sensor signal is not reaching panel/receiver because sensor is too far away.
Feature Problem Action/Solution 1. 2. 3. Check that the module is wired correctly to the panel terminals. Verify the module LED is flashing continuously. If the LED is not flashing, remove power and check wiring. There is a 5-minute delay after the module returns control to the furnace/AC thermostat, before the module overrides the thermostat again. Wait 5-minutes and try again. Module temperature does not match actual room temperature.
Feature Problem Action/Solution Module is not communicating on Bus and indicates a “Bus Failure Unit nn”. Where nn represents the Wireless Gateway unit number. 1. 2. Check that the module is wired correctly to the panel terminals. Verify that the module’s red Bus LED is flashing. If not, remove power and check all the wiring. Module’s status LED’s don’t turn on after initial power-up. 1. 2. 3. Wait 5 - 8 minutes for the module to communicate with alarm.com.
Appendix A: System Planning Worksheets Customer Name _________________________________ Address _______________________________________ City _________________ County ___________ State ___ Zip __________ Phone (____) ___________ Table A1: Wireless Devices Part No. 60-362 Description Qty.
Table A2: Hardwire Devices Part No. Description Qty. mA (Max.
Table A3: Zone and Sensor Assignments (Continued) No.
Table A3: Zone and Sensor Assignments (Continued) No.
Table A4: System Settings Index and Record Setting (reference) default Shortcut No. Setting Installer Programming—8 + Installer/Dealer CODE + 00 24 Hour Tamper Off 06000 AC Failure Off 06010 Access Code Lock (On) 0003 Access Timeout 90 sec 0904 Account No.
Table A4: System Settings Index and Record (Continued) Setting (reference) default Shortcut No.
Table A4: System Settings Index and Record (Continued) Setting (reference) default Shortcut No. Phone Test On 02000 Phone Test Freq. 7 days 0302 Police Panic On 0512, 0522 Program Report Off 06015 Setting 1_____________2_____________ Quick Arm Off 0011, 0021 1_____________2_____________ Quick Exit On 0012.
Appendix B: Reference Tables CS Report √ √ √ √ √ 1, 2, 3 √ √ 1, 2, 3 √ √ 1, 2, 3 Auxiliary Instant √ 1, 2, 3 Portable Auxiliary 24-hour portable auxiliary button. Siren shutoff confirms CS report. Auxiliary Instant √ 1, 2, 3 08 Special Intrusion Special belongings, such as gun cabinets and wall safes. Police Instant √ √ √ 1, 2, 3 09 Special belongings, such as gun cabinets and wall Special Intrusion safes.
Restoral Supervisory CS Report Active Levels Chime (Level 1) Table B1: Sensor Group Characteristics (Continued) 26 Fire 24-hour fire, rate-of-rise heat, and smoke sensors. Fire Instant √ √ √ 27 Output Module Hardwire Output Module (HOM) lamp control or other customer feature. ‡ Silent Instant √ √ 1, 2, 3 28 Output Module HOM, PIR motion sensor, sound sensor, or pressure mat. ‡ Silent Instant √ 1, 2, 3 29 Auxiliary Freeze sensor.
Table B2: Item Numbers and Sensor Text Item # 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 Sensor Text Aborted AC Access Active Activity Alarm All AM Area Arm Armed Arming Attic Auxiliary Away Baby Back Bar Basement Bathroom Battery Bedroom Bottom Breezeway Building Bus Bypass Bypassed Cabinet Canceled Car Carbon Monoxide Central Chime Closed Closet Closing Code Computer Control Concord Ultra
Table B3: System Event Trigger Numbers System Event Trigger No. Description Null Trigger (used for direct control) Activated only by schedule or direct command. 000 Fire Alarm When Fire sirens are started. 001 Police Alarm When Police sirens are started. 002 Auxiliary Alarm When Auxiliary sirens are started. 003 Any Audible Alarm When any of the above sirens are started.
Table B4: Sensor Group Event Trigger Numbers Sensor Group Trigger No. Sensor Group Trigger No.
Table B5: Sensor Number Event Trigger Numbers Sensor Number 87 State Trigger No. State Trigger No.
Table B5: Sensor Number Event Trigger Numbers Sensor Number State Trigger No. State Trigger No.
Table B6: System Feature Event Trigger Numbers Feature State Trigger No. Opening Report occurred 242 Closing Report occurred 243 Latchkey Opening or Closing occurred 244 Duress alarm 245 Force Armed Report occurred 246 Fire in Partition alarm 247 Recent Closing Report occurred 248 entered 249 Sensor Test Table B7: Response Characteristics Response Characteristics Description Momentary trip time The point will remain activated for nn seconds (n is 1-12 seconds).
Notes for Table B8: Response Numbers Note The mechanical lifetime of the relay may be exceeded if an output is set up for a siren tracking response and a pulsing siren (auxiliary or fire) is active for long time periods. A SnapCard relay output’s lifetime expectancy is about 350 total pulsing hours. 1. If an event does not trigger sirens, siren tracking response numbers activate without turning on the output. If sirens are triggered by another event, the output pulses to match the siren.
Appendix C: Settings To Enter Programming Mode: 8 + Installer or Dealer Code + 0 + 0 Tier 1 Menus Tier 2 Menus # System Programming * * ) * Security * # ) * Global Demo Kit On Off * ) # 0 0 0 0 * Account Number 00000 ) * # Account Number 00000 * Dealer Code * ) Phone Number 0 1 2 0 * * ) * * ) High Lvl Rpts On Off 0 1 0 1 0 1 1 1 0 1 2 1 * ) * ) Low Lvl Rpts On Off * ) * ) Low Lvl Rpts On Off Low Lvl Rpts On Off 0 1 1 2 0 1 0 2 * * High Lvl Rpts On Off ) 0
Tier 2 Menus (Continued) B A A B B Pager Phone 1 * # B Pager Phone 2 A Phone Number 0 1 3 0 B A A * # B Pager Phone 3 * # B Pager Phone 4 A A * # B Pager Phone 5 * # Downloader Phone A Phone Number Phone Number Phone Number Phone Number Phone Number 0 1 4 0 B 0 1 5 0 B 0 1 6 0 B 0 1 7 0 B 0 1 8 0 A A A A High Lvl Rpts On Off High Lvl Rpts On Off High Lvl Rpts On Off High Lvl Rpts On Off High Lvl Rpts On Off 0 1 3 1 0 1 4 1 0 1 5 1 0 1 6 1 0 1 7 1 B A B A
Tier 2 Menus (Continued) * * Timers ) * # ) * Partition 1 * ) Partition 2 ) * # Sup vs. Time Rndm 1:00-4:00 Entry Delay 32 secs (32-240) 0 3 0 0 0 3 1 0 * ) # * ) * * ) Exit Delay 64 secs (48-184) Exit Delay 64 secs (48-184) 0 3 0 1 0 3 1 1 0 3 2 1 * ) * ) Extended Delay 4 mins (1-8) 0 3 0 2 0 3 1 2 0 3 2 2 * Next Ph.
Tier 2 Menus (Continued) * * ) Reporting * # Global Partition 1 Partition 2 * 24-Hr Tamper On Off 0 6 0 0 0 ) # Opening Rpts On Off 0 6 2 0 0 * * * ) 0 6 0 0 1 0 6 1 0 1 ) * Back in Service On Off 0 6 0 0 2 * ) ) Low CPU Batt. On Off * Duress On Off 0 6 0 0 4 ) * Batt.
Tier 2 Menus (Continued) * * Audio Verification * # ) Accessory Modules ) * # # * Bus Device Partition 1 * * # Audio Verify On Off SnapCards ) * # Unit - ID 0 9 0 0 1 0 0 n n (n n = 0 0 -1 5 ) * ) * # Audio Mode 1 0 9 0 1 * Fire Shutdown On Off 0 9 0 2 * * Output Programming ) Output Text ) * # * # ) Silent Talkback On Off 0 9 0 3 * * * * ) Access Timeout 90 secs (30-300) 0 9 0 4 Output 1 * Partition Assign 1 2 1 0 1 0 0 0 Partiton Assign 1 2 1 0 1 0 1 0 * * Output
Press B to Return To Security Menu Tier 2 Menus * ) * # ) * # ) * * Output Programming Inputs ) * # Two-Wire Smk On Off 1 1 0 1 * # # ) 1 1 2 1 * * # Output 1 Item n Output 2 Item n 1 1 1 1 0 ) Configuration 01614 1 1 1 0 1 * Partition Assign 12 1 1 1 0 0 * Output 2 1 1 2 0 ) Partition Assign 12 * Output 1 Output 2 Output 1 ) * # 1 1 0 0 * Output Text * # Smoke Verify On Off Appendix C: Software Release Notes * Onboard Options * ) Configuration 01710 1 1 1 1
Exit Delay • The low limit on Exit Delay (0311/0321) has been changed from 48 to 45 seconds, with the default setting changing from 64 to 60 seconds. Existing versions of Toolbox will still show a low limit of 48 seconds and a default setting of 64 seconds. When setting the Exit Delay in installer program mode, entering any number between 45 and 55 will result in an Exit Delay of 45 seconds and entering any number between 60 and 71 will result in an Exit Delay of 60 seconds.
System Wiring Notes Note 1 Class II power transformer must be plugged into an unswitched AC power receptacle. Do not short the transformer terminals together. The transformer contains an internal fuse that permanently disables the output if the terminals are shorted. Note 2 An alphanumeric touchpad is required for on-site programming. Note 3 Speaker terminals 7 and 8 activate only for alarms in partition 1. Use speakers with an 8ohm or higher impedance.
2 1 3 5 3 1 1 3 4 6 Splice Separate Wire Cables B U S B To Furnace 1 Thermostat 3 5 4 6 3 1 8 2 3 4 5 6 1 1 1 0 Note 3: 2 (15-Watt) 8 Ohm Speaker 7 8 9 Not Used 6 3 1 2 3 4 5 6 7 8 9 1 6 1 5 6 1 0 1 1 1 2 1 3 1 4 1 5 1 6 4 3 4 1 H IG H 1 0 2 G N D 3 L O W 1 9 Z O N E 6 L P 4 L N 9 Black 2 0 G N D - 3 G N D 1 + 1 2 V A 2 4 + 1 2 V B 3 5 A 4 G N D B U S 5 G N D B 6 4 4 M M 3 3 M 1 2 1 8 2 4 Grn 2 5 Brn 9 8 1 0 A U D 1 A