Installation Instructions Overthe Range Microwave Oven CVM2072 Questions?Call 800.GE.CARES(800.432.2737)or Visit,,,, x_ebsite;,t:ge.com BEFORE YOU BEGIN Read these instructions completely • IMPORTANT instructions for local • Note codes and to Installer instructions with the carefully. - S_.e_hese inspector's • IMPORTANT goxernin(, and - Obse,,e;,ll Be sure to leaxe these Note to Consumer instructions - Keep for futm'e reterence.
Installation Instructions Redrculating CONTENTS General information hnportant Safety ........................................ Attach Mounting Preparation Instructions .................................. Hood Requirements Exhaust Damage Parts Included. Tools installation Removing Plate tire Mounting Plate Wall Plate ............................... l.oration Exhaust Top Checking Operation Mount Plate of Top to W;fll ....... Cabinet .......... 1or Proper Damper ...................
Installation Instructions iMPORTANT SAFETY iNSTRUCTiONS This product requires a three-prong groronled outlet. The installer must perflmu a ground continuit_ check on the power outlet box befl_re beginning the installation to insm'e that the outlet box is properly grotmded. If not properly grotmded, or if the outlet box does not meet electrical requirements noted (troder E1,E(_TRICAI_ REQLIIREMENTS), a qualified electrician should be employed to correct any deficiencies.
Installation Instructions HOOD EXHAUST NOTE: Read outside. If you these next plan OUTSIDE two pages to recirculate tufty if you the air back TOP EXHAUST The following chart ductwork installation. describes plan to vent into the an example ot one exhaust to the proceed (EXAMPLE to page 6. ONLY) possible EQUIVALENT LENGTH DUCT PIECES 12 Ft.Straight Duct RoofCap (6" Round) x 12 Ft. 24 Ft. TransitionAdaptor* Rectangular-to-Round -_ your room, xx 5 Ft.
Installation NOTE: If wm duct lengti_ round duct Outside the NOTE: direct ensm'es hood that the Maximum total or 6" diameter 140 requires equivalent a HOOD that route clear and venting make is blocking Exhaust exceed note feet. EXHAUST DUCT. the venting with be installed as few elbows of exhaust and dmnpers swing sure as possible. prevent freely and ducts.
Installation Instructions PARTS iNCLUDED DAMAGE - SHIPMENT/ iNSTALLATiON HARDWARE * If the unit unit is damaged to the store in shipment, in which it was return bought the PART QUANTITY fin" repair Wood Screws or replacement, ® If the unit replacement ® If the th;m unit the PACKET 2 (Y4"x 2") is damaged is the by the customer, responsibility is damaged customer), be made by ;uT;mgement and installer.
Installation Instructions TOOLS YOU WILL NEED Ruleror tape measureand # 1 and#2 Phillipsscrewdriver Pencil t edge (optional) Carpentersquare Tin snips(for cutting damper,if required) Scissors (to cut template,if necessary) Electricdrill with ¾_",V/" and%" drill bits Fillerblocksor scrap wood pieces,if needed for top cabinetspacing (usedon recessedbottom cabinet installationsonly) Gloves Saw(saber,hole or keyhole) Studfinder er Safetygoggles MOUNTING Hammer(optional) Ductandmaskingtape Level
Installation I- PLACEMENT N Instructions OF THE MOUNTING REMOVING THE MICROWAVE OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE _ [] Remove the installation tray and the small the Swrofl)am instructions, hardware protecting Fold back all 4 carton sides. Then careflfllv onto the top the Stvrofl)am. side. bag. the filters, Do fl'ont m'he oven should FINDING THE WALL STUDS glass not remove of the oven.
Installation DETERMINING Plate position Instructions WALL PLATE LOCATION - beneath flat bottom UNDER YOUR CABINET Plate position - beneath cabinet bottom framed recessed %*, '', Mounting Plate Tabs the Cabinet Bottom Mounting Plate Tabs Touching the Back Frame / ill III I III 30" to Cooktop III At least 30", up to 36" Plate position - beneath recessed cabinet with front overhang bottom Your with cabinets may the microwave trim to install level.
Installation ALIGNING Instructions THE WALL PLATE ¢ / -'-'- HoleB J , / o-,:)OoOo OoOoyoOoOoOo °o°o°oOo Area E H01eD CAUTION: _,_ar glo_es to a_oid cutting finge_ on sharp edces O " []Draw a vertical line on the wall at the center 30" wide space. _Use _ the moui_ting plate as the template for the rear wall. Place the motmting plate on the wall, making sure that the tabs are touchhag the bottom of the cabinet or the level line drawn in Step C for cabinets with front overhm_g.
Installation I2-] INSTALLATION TYPES This microwave oven is designed for adaptation the tolh)wing three types of ventilation: A. Outside Top Exhaust B. Outside Back Exhaust C. Recirculating _-_ (Vertical (Choose to A, B or C) NOTE: This microwave is shii)ped assembled fl_r Outside Top Exhaust (except ti)r non-vented models). Select the type of ventilation required for vom" installation and proceed to that section.
Installation Instructions OUTSIDE TOP EXHAUST INSTALLATION A1. A2. A3. A4, (Vertical Duct) OVERVIEW Attach Mom_ting Plate to _\'all Prepare Top Cabinet Check Damper Operation Mom_t Microwave Oven AS, A_!just Exhaust Adaptor A6, Connect Ductwork @ I-_ To use toggle ATTACH THE MOUNTING PLATE TO THE WALL bolts: Spacingfor Toggles MoreThanWall ÷l_.-i..
Installation I-_ You hole and Instructions MOUNT OVEN USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET need to drill holes enough for large a cutout large fl)r the the power enough for top SUl)port cord the screws, a to fit throu ,h exhaust THE MICROWAVE adaptor. FOIl EASIER INSTAI,IATION AND PERSONAI, SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle during installation. NOTE: % " Read the instructions TEMPLATE.
Installation I-_ MOUNT Instructions ADJUST THE EXHAUST ADAPTOR THE MICROWAVE OVEN (cont.) CabinetFront Open to CabinetBottomShelf connect tile top cabinet and a(!iust to tile house duct. Filler Block Blower Plate _ tile exhaust Damper , --\__ adaptor Backof Microwave to Depth ofquivalent Cabinet Recess _ Self-AligningScrew [ MicrowaveOvenTop []Attach tile microwave oven " to tile top cabinet.
Installation Instructions OUTSIDE BACK EXHAUST INSTALLATION B1. B2. B3. B4. BS. B6. I-_ &el (Horizontal Duct) OVERVIEW Prepare Rear Wall Remove Exhaust Adaptor Attach Mounting Plate to _'all Prepare Top Cabinet A(!just Blower Mount the Microwave Oven PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST go/I Ileed to tilt outside exhaust. }lll Ol)eniw* in the rear REMOVE EXHAUST ADAPTOR This microwave oven is shii)ped assembled for top exhaust.
Installation L==,=,=,=,=,=,=,=,=_ Instructions ATTACH THE MOUNTING PLATE TO THE WALL i I iiil ' ii | '_ L USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for tile top support screws and a hole large enouoh for tl/e power cord to fit throu ,h Attach the plate to the wall using toggle bolts. At least one wood screw illtlSt be used to attach the plate to a wall stud. []Remove tile toggle wings ti'om tile bolts.
Installation Instructions ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST (cont.
Installation MOUNT OVEN Instructions []Insert a sell=aligning screw through top center cabinet hole. Temporarily secm'e tile oven by turning tile screw at least two full turns after tile threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight.
Installation RECIRCULATING INSTALLATION Instructions INo.-Ve.tedD.c.essl OVERVIEW C1. Attach Mounting Plate to Will C2. Prepare Top Cabinet C3. Check Microwave Assembly C4. A(!just Blower C5, Mount the Microwave C6, Install Charcoal Filter I-_ i i Oven i i _ ATTACH THE MOUNTING PLATE TO THE WALL Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to nlount the plate.
Installation Instructions CHECK MICROWAVE ASSEMBLY Exhaust on Adaptor models (absent shipped recirculation _ for Carefully pull out tile will extend tar enough blower trait. blower unit. Tile wires to allow xou to adjust tile exhaust).\ i__ _ _ack of , EXT- M,cr°wave i " Place tile microwave in its upright top of tile trait facing up. position, with tile " Tile microwave oven may be shipped assembled for top exhaust (adaptor installed) or fin" recirculation exhaust (adaptor absent).
Installation Instructions NOTE: ADAPTING MICROWAVE BLOWER FOR RECIRCULATION {cont.) []Guide tile wire do_n into tile blower rests securel) in front of tile blo_er. o })ening tile mo/mting oven_ thread power cord through hole in bottom of top cabinet, Kee I) it tight throughout Steps 1-3. Do not pinch cord or lilt oxen by• I )ullino & cord._ so it , When illicYowave _I,ifl microwave, tilt it fin'ward, and hook slots at back bottom edge tabs onto t()/li" lower of mounting plate.
Installation MOUNT Instructions iNSTALLiNG THE CHARCOAL FILTER THE MICROWAVE OVEN {cont.) [] []Insert 2 self-alioning screws throuoh_ outer top cabinet holes. each TtlI'n two flfll ttlI'IlS on Remoxe Phillips []Open screw. [] screws on top front screwdrix er. of grille using a #2 the door. Remoxe the grille. Slide the ,grille to the left and pull it ,strai,*ht_ oft. Charcoal j-f Tighten center screw completely: [] Tighten the outer two screws to the top of the microwave oven.
Installation Instructions BEFORE YOU USE YOUR MICROWAVE V_ Make sureaccording the microwa'_e has been installed to inst_ o',en uctions. F_ Remo_e illicrowax, I Install _ Replace [-_ I all )acking e ox,en. turntable house -_ material and fl/se ring or tm'n from the in caxitv. breaker back on. I]1 IIIIIIII -_ lug poweroutlet. cord electrical into a dedicated 15- to 20-amp Ensureproper groundexists/ beforeuse 23 Read the Owner's Mantml.
DE68-03410A 49- 40558 04-07 JR P6nted in Malaysia
